PPE 228053200 Heavy-Duty Cast Aluminum Deep Transmission Pan Installation Guide
- June 9, 2024
- PPE
Table of Contents
Heavy-Duty Cast Aluminum
Deep Transmission Pan
Aisin AS69RC
(228053200, 228053210, 228053220)
Installation Guide
Aisin AS69RC
CONTENTS
A: (1) Deep Transmission Pan
B: (1) PPE Aramid Fiber Gasket
C: (1) Drain Plug (installed)
D: (20) M6-1.0 x 25mm socket head cap bolts
E: (20) M6 flat washers
F: (1) 1/8” NPT port plug (installed)
INSTALLATION
Step 1. Vehicle off. Engine cool. Drain fluid.
Step 2. Clean mating surfaces.
Step 3. Tighten PPE Drain Plug and NPT plug if necessary.
Step 4. Install PPE Gasket.
Step 5. Assemble 2 M6 bolts and washers and fit them throught the pan flange
along the centerline (1, 2 in Fig1). Thread the bolt assembly to secure.
Finger tight for now.
Step 6. Assemble and install remaining bolts and washers. Finger tight for
now.
Step 7. Tighten in a crossing pattern as shown in Fig 1. Torque to 8-10 ft
lbs.
Step 8. Fill with recommended fluid. Start engine.
Check for leaks. Top off fluid if necessary
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory
specifications. Additional horsepower creates more stress on the drive-train
components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE
LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR
REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE
products. The installation of this product indicates that the Buyer has read
and understands this agreement and accepts the terms and conditions. PPE
(Pacific Performance Engineering) Inc., its distributors, employees, and
dealers (the “Seller”) shall not be responsible for the product’s proper use
and service. The buyer hereby waives all liability claims. The Buyer hereby
acknowledges no reliance on the Seller’s skill or judgment to select or
furnish goods suitable for any particular purpose and that there are no
liabilities which extend beyond the description on the face hereof, and the
Buyer hereby waives all remedies or liabilities expressed or implied, arising
by law or otherwise (including without any obligation of the Seller with
respect to fitness, merchantability and consequential damages), or whether or
not occasioned by the Seller’s negligence. The Seller disclaims any warranty
and expressly disclaims any liability for personal injury or damages. The
Buyer acknowledges and agrees that the disclaimer of any liability for
personal injury is a material term for this agreement and the Buyer agrees to
indemnify the Seller and to hold the Seller harmless from any claim related to
the item of equipment purchased. Under no circumstances will the Seller be
liable for any damages or expenses by reason of use or sale of any such
equipment. The Seller assumes no liability regarding the improper installation
or misapplication of its products. It is the installer’s responsibility to
check for proper installation and if in doubt, contact the manufacturer. The
Buyer is solely responsible for all warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability,
and fitness for a particular purpose, productiveness, or any other matter of
Seller’s product sold herewith. The Seller shall not be responsible for the
products proper use and service and the Buyer hereby waives all rights other
than those expressly written herein. This warranty shall not be extended,
altered or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE
Transmission Coolers.
Three (3) year limited warranty on PPE Manifolds and Up-Pipes Kits, and OEM-
Length Up-Pipes. One (1) year limited warranty on all other PPE products from
the date of sale to original buyer and limited solely to the parts contained
within the products kit. All products that are in question of Warranty must be
returned prepaid to the Seller and must be accompanied by a dated proof of
purchase receipt. All Warranty claims are subject to approval by Seller. Under
no circumstances will the Seller be liable for any labor charged or travel
time incurred in diagnosis for defects, removal, or re-installation – of this
product or any other contingent expenses. Under no circumstances will the
Seller be liable for any damage or expenses incurred by reason of the use or
sale of any such equipment. In the event that the buyer does not agree with
this agreement: the buyer may promptly return this product, in a new and
unused condition in its original packaging, with a dated proof of purchase to
the place of purchase within ten (10) days from date of purchase for a full
refund. The installation of this product indicates that the buyer has read and
understands this agreement and accepts its terms and conditions.
PACIFIC PERFORMANCE ENGINEERING
PPEpower.com
Documents / Resources
| PPE
228053200 Heavy-Duty Cast Aluminum Deep Transmission
Pan
[pdf] Installation Guide
228053200 Heavy-Duty Cast Aluminum Deep Transmission Pan, 228053200, Heavy-
Duty Cast Aluminum Deep Transmission Pan Aluminum Deep Transmission Pan, Deep
Transmission Pan
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>