WAGO 787-1014 Primary Switched-Mode Power Supply Instruction Manual

June 9, 2024
WAGO


Instruction Manual

787-1014

Primary switched-mode power supply

005-0191 / Rev. a 09.02.2022

Connection

WAGO Primary Switched-Mode Power Supply A03

Installation

Safety measures before installation
This equipment is to be protected against improper use. Components are not to be bent or isolation spacing changed, especially through handling and transport. The contact with electrical components and terminals is to be avoided. Always disconnect the equipment from the mains supply, before commencing installation or wiring. The product description, technical information in our main catalogue and the marking on the equipment ratings plate are to be observed.

Installation
Installation must be carried out according to the prevailing local conditions and safety regulations (e.g. VDE 0100) national accident prevention regulations (e.g. UVV-VBG4 or BGV A3) and the generally accepted rules of technology. This equipment is a component designed for installation into electrical systems and machines, and fulfils the requirements of the low voltage guidelines (2014/35/EU).

The required minimum spacing to neighbouring components must be observed to guarantee the required cooling. When installed into machinery, the normal operation is forbidden until it is determined that the machine fulfils the requirements of the machinery guidelines (2006/42/EG). EN 60204 must be observed. The EMC requirements (2014/30/EU) must be fulfilled before operation is commenced. The observance of the required limitations for the EMC legislation is the responsibility of the manufacturer of the installation or machinery.

Terminals handling

1 LED: The green LED lights as soon as the output voltage is present.
2 Input
3 Output
4 Mounting: Place the device with the DIN rail guide on the upper edge of the DIN rail, and snap it in with a downward motion.
5 Removing: Pull the snap lever open with the aid of a screwdriver and slide the device out at the lower edge of the DIN rail.

Output Characteristic (U/I Charakteristic)

Technical data

| 787-1014
---|---
Input|
Rated input voltage| 110 Vdc
Operating input voltage range| 77 – 140 Vdc
Derating input voltage| —
Rated frequency range| 0 Hz
Rated input current at nominal load (77 / 110 Vdc)| 0.77 / 0.42 A
In-rush current limiter| < 30 A, NTC
internal fuse| 4 AT
Mains drop compensation at nominal load (77 / 110 Vdc)| 8 / 25 ms
Output|
Rated output voltage| 24 Vdc ± 2 %,  ± 10 % in scope of EN 50121-3-2
Rated output current| 2 A
Overloadbehaviour| Constant current (U/I Line)
Efficiency| typ. 85 %
Residual ripple (nominal load)| typ. 100 mVss
Signaling|
Power indicator| LED green
Environment|
Storage Temperature| -40 °C … +85 °C
Ambient termperature|

-40 °C … +70 °C
Derating: -1,5 % / K (> +55 °C)
Device start at -40 °C type-tested

Mounting position| horizontal for Rail TH 35
Allowable humidity| 5 to 96 % relative humidity with no dew, coated PCB
Current rating at any mounting position| max. 1.6 A
Cooling (spacing to vicinal components)| No minimum spacing right/left required, 50 mm over/under
Shock and vibration| Category 1, Class B (acc. EN 61373:2010)
Safety and protection|
Protection index| IP 20
HV test voltage| 4242 Vdc
Safety class| II ( in the closed Cabinet)
Conductors| Use Copper Conductors only, rated 75 °C. Conductor length (output) max. 3m.
Installation| Degree of Pollution 2, Over-voltage Category II
Feedback voltage| max. 35 Vdc
Output serial connection| yes
Output parallel connection| yes
MTBF (acc. IEC 61709)| > 500 000 h
Fire load| < 7 MJ
Safety standards|
Safety| EN 61010-1, EN 61010-2-201, EN 61558-2-16 EN 61140 (SELV) EN 50125
EMC| EN 61204-3, EN 50121-3-2, EN 50121-3-2:2017, EMV 06
Order numbers| 787-1014
Mechanical Data|
weight| 0.24 kg
Dimensions width x height x depth*| 72 x 89 x 55 mm
Terminals input (+, -) / output (+, +, -, -)| WAGO series 740 max. 2.5 mm²

  • Depth from upper edge of DIN rail.
Functional diagram

WAGO Primary Switched-Mode Power Supply A05

WAGO GmbH & Co. KG
Hansastr. 27
32423 Minden
Germany
Phone: +49 571-887-0
Fax: +49 571-887-169
info@wago.com
www.wago.com

Subject to change.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals