WAGO 750-1406 16 Channel Digital Input High Side Switching User Guide

WAGO 750-1406 16 Channel Digital Input High Side Switching

Provisions

This document applies to the following product:

• 750-1406 (16DI 24 VDC 0.2 ms) 16-channel digital input; 24 VDC; 0.2 ms; high-side switching
  • Product detail page www.wago.com/750-1406.

Note applicable documents!

• The complete operating instructions for the product consist of several documents.
• The product must only be installed and operated in accordance with the complete operating instructions.
• Knowledge of the entire operating instructions is required for proper use.
• You can find all the documents and information on the detailed product page.

Applicable document

System Manual I/O System 750/753

• Provisions
• Safety
• Transport and Storage
• Assembly and Disassembly
• Conductor Termination
• Decommissioning

Overview

• The I/O module acquires binary control signals from field devices (e.g., sensors, encoders, switches or proximity switches).
• The I/O module has 16 input channels and directly connects to 1-wire sensors.
• Each input channel has a noise-rejection RC filter with a 0.2 ms time constant.
• The I/O module inputs provide high-side switching. If the 24 V potential for field power is switched to an input connection, the signal status for the corresponding input channel is set to “high.”
• For each channel, a green status LED indicates the signal status.
• The field level and the system level are electrically isolated from one another.
• The I/O module can be operated on all head stations of the WAGO I/O System 750/753.

Properties

Note Read system manual!

• You can find cross-product information on the topic of System Features in the
  • System Manual I/O System 750/753.

View

System Manual I/O System 750/753
6| Push-in CAGE CLAMP® connection| “‘E Wiring Interface [ ► 8] and

W System Manual I/O System 750/753

7| Power jumper contacts (spring)| “‘E Power Jumper Contacts [ ► 9 ] and

W System Manual I/O System 750/753

8| Release tab| W System Manual I/O System 750/753
9| Power jumper contacts (blade)| “‘E Power Jumper Contacts [ ► 9] and

W System Manual I/O System 750/753

Indicators
For each channel, a green status LED indicates the signal status.

Wiring Interface

Figure 3: Push-in CAGE CLAMP® connections

Power Jumper Contacts
The potential for the field supply is fed in via the power jumper contacts and passed on via the spring contacts.

2
3| Power jumper contact
4

Arrangement in the Bus Node

• For the mechanical arrangement of the I/O module, the previous component must have at least 2 open grooves for accommodating the power jumper contacts.
• For electrical compatibility requirements see Section 8 Circuit Diagram [} 10].

Circuit Diagram

For information on the system power supply, please see & System Manual I/O System 750/753

Functions

Signal Processing

• Each input channel has a noise-rejection RC filter with a 0.2 ms time constant.
• The I/O module inputs provide high-side switching.
• If the 24 V potential for field power is switched to an input connection, the signal status for the corresponding input channel is set to “high.”

Process Image

Bit 7| Bit 6| Bit 5| Bit 4| Bit 3| Bit 2| Bit 1| Bit 0
---|---|---|---|---|---|---|---
DI 8| DI 7| DI 6| DI 5| DI 4| DI 3| DI 2| DI 1
DI 1| DI 1 signal status – digital input channel 1
DI 2| DI 2 signal status – digital input channel 2
DI 3| DI 3 signal status – digital input channel 3
DI 4| DI 4 signal status – digital input channel 4
DI 5| DI 5 signal status – digital input channel 5
DI 6| DI 6 signal status – digital input channel 6
DI 7| DI 7 signal status – digital input channel 7
DI 8| DI 8 signal status – digital input channel 8
Bit 15| Bit 14| Bit 13| Bit 12| Bit 11| Bit 10| Bit 9| Bit 8
---|---|---|---|---|---|---|---
DI 16| DI 15| DI 14| DI 13| DI 12| DI 11| DI 10| DI 9
DI 9| DI 9 signal status – digital input channel 9
DI 10| DI 10 signal status – digital input channel 10
DI 11| DI 11 signal status – digital input channel 11
DI 12| DI 12 signal status – digital input channel 12
DI 13| DI 13 signal status – digital input channel 13
DI 14| DI 14 signal status – digital input channel 14
DI 15| DI 15 signal status – digital input channel 15
DI 16| DI 16 signal status – digital input channel 16

Planning

Note Read system manual!

• You can find cross-product information on the topic of Planning in the & System Manual I/O System 750/753.

Compatibility

• The I/O module can be operated on all head stations of the WAGO I/O System 750/753.

Requirements for Wiring and Accessories

• If applicable, use appropriate potential multiplication modules (e.g., item no. ü 750-1605,
• 750-1606 or ü 750-1607) for the power supply to the sensors.
• The I/O module has no power jumper contacts for receiving and forwarding the ground potential. Use a potential distribution module (e.g., Item No.: ü 750-601, ü 750-602,
• 750-610 or ü 750-612) if the subsequent I/O modules require ground potential supply.
• An operating tool with a 2.5 mm blade (e.g., item no. ü 210-719) is required for opening the Push-in CAGE CLAMP® connections.

Connection Example

Appendix

Technical Data, Approvals, Guidelines and Standards See also

• 2 Data sheet 750-1406 [} 14]

Note Subject to changes!

• Please also observe the further product documentation! You can generate the current datasheet at any time at:
  • www.wago.com/<item. number>.
• This digital input module features 16 channels in a width of just 12 mm (0.47 inches).
• The module features Push-in CAGE CLAMP® connections enabling solid conductors to be connected by simply pushing them in.
• Each input channel has a noise-rejection RC filter with a 0.2 ms time constant.
• A green LED indicates the signal state of each channel.
• Field and system levels are electrically isolated.
• An operating tool with a 2.5 mm blade (210-719) is required to open the Push-in CAGE CLAMP® connections.

Technical data

• Number of digital inputs 16
• Total number of channels (module) 16
• Signal type Voltage
• Signal type (voltage) 24 VDC
• Sensor connection 16 x (1-wire)
• Input characteristic high-side switching
• Input filter (digital) 0.2 ms
• Input current per channel for signal (0) typ. 0.6 mA
• Input current per channel for signal (1) typ. 2.3 mA
• Input current per channel for signal (1) min. 2.1 mA
• Input current per channel for signal (1) max. 2.4 mA
• Voltage range for signal (0) −3 … +5 VDC
• Voltage range for signal (1) 15 … 30 VDC
• Input data width (internal) max. 16 bits
• Supply voltage (system) 5 VDC; via data contacts
• Current consumption (5 V system supply) 25 mA
• Supply voltage (field) 24 VDC (-25 … +30 %); via power jumper contacts (power supply via blade contact;
• transmission via spring contact)
• Isolation 500 V system/field
• Indicators LED (1-16) green: Status DI 1 … DI 16
• Number of incoming power jumper contacts 2
• Number of outgoing power jumper contacts 2
• Current carrying capacity (power jumper contacts) 10 A

Connection data

• Connection technology: inputs/outputs 16 x Push-in CAGE CLAMP®
• Connection type 1 Inputs/outputs
• Solid conductor 0.08 … 1.5 mm² / 28 … 16 AWG
• Fine-stranded conductor 0.25 … 1.5 mm² / 22 … 16 AWG
• Strip length 8 … 9 mm / 0.31 … 0.35 inches
• Conductor type (1) f-st
• Conductor type (2) s
• Conductor type 1 fine-stranded
• Conductor type 2 solid

Physical data

• Width 12 mm / 0.472 inches
• Height 100 mm / 3.937 inches
• Depth 69 mm / 2.717 inches
• Depth from upper-edge of DIN-rail 61.8 mm / 2.433 inches

Mechanical data

• Mounting type DIN-35 rail
• Pluggable connector fixed

Material data

• Housing material Polycarbonate; polyamide 6.6
• Fire load 0.824 MJ
• Weight 47.5 g
• Conformity marking CE

Environmental requirements

• Ambient temperature (operation) 0 … +55 °C
• Surrounding air temperature (storage) -25 … +85 °C
• Protection type IP20
• Pollution degree (5) 2 per IEC 61131-2
• Operating altitude 0 … 2000 m / 0 … 6562 ft
• Mounting position horizontal (standing/lying); vertical
• Relative humidity (without condensation) 95 %
• Vibration resistance 4g per IEC 60068-2-6
• Shock resistance 15g per IEC 60068-2-27
• EMC immunity to interference per EN 61000-6-2, marine applications
• EMC emission of interference per EN 61000-6-3, marine applications
• Exposure to pollutants per IEC 60068-2-42 and IEC 60068-2-43
• Permissible H2S contaminant concentration at a relative humidity of 75 % 10 ppm
• Permissible SO2 contaminant concentration at a relative humidity of 75 % 25 ppm

CONTACT

• WAGO GmbH & Co. KG
• Postfach 2880 · D – 32385 Minden
• Hansastraße 27 · D – 32423 Minden
• info@wago.com.
• www.wago.com.
• Headquarters + 49 571/887 – 0
• Sales + 49 (0) 571/887 – 44 222
• Order Service + 49 (0) 571/887 – 44 333
• Fax + 49 571/887 – 844169

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Copyright – WAGO GmbH & Co. KG – All rights reserved. The content and structure of the WAGO websites, catalogs, videos and other WAGO media are subject to copyright. Distribution or modification of the contents of these pages and videos is prohibited. Furthermore, the content may neither be copied nor made available to third parties for commercial purposes. Also subject to copyright are the images and videos that were made available to WAGO GmbH & Co. KG by third parties.

WAGO I/O System 750/753

• 16-channel digital input:  24 VDC; 0.2 ms; high-side switching 750-1406
• Version 2.0.0

© 2022 WAGO GmbH & Co. KG
All rights reserved.

WAGO GmbH & Co. KG

• Hansastraße 27
• D – 32423 Minden
• Phone: +49 571/887 – 0
• Fax: +49 571/887 – 844169
• E-Mail: info@wago.com.
• Internet: www.wago.com.

Technical Support

• Phone: +49 571/887 – 44555
• Fax: +49 571/887 – 844555
• E-Mail: support@wago.com.

Every conceivable measure has been taken to ensure the accuracy and completeness of this documentation. However, as errors can never be fully excluded, we always appreciate any information or suggestions for improving the documentation.

• E-Mail: documentation@wago.com.
• We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent.
• WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
• Version: 2.0.0
• 16DI 24V DC 0.2ms

References

• Operating tool (210-719) | WAGO USA
• 16-channel digital input (750-1406) | WAGO USA
• Potential Distribution (750-1605) | WAGO USA
• Potential Distribution (750-1606) | WAGO USA
• Potential Distribution (750-1607) | WAGO USA
• Power Supply (750-601) | WAGO USA
• Power Supply (750-602) | WAGO USA
• Power Supply (750-610) | WAGO USA
• Power Supply (750-612) | WAGO USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>