guard RFID ST-4-WIFI Wi-Fi Staff Tag User Manual

: June 9, 2024
: guard RFID

Table of Contents

guard RFID ST-4-WIFI Wi-Fi Staff Tag
FEATURES
DESCRIPTION
SPECIFICATIONS
REQUIRED WI-FI RTLS LICENSES
TAG ACTIVATOR
WI-FI TAG CHARGER
FCC STATEMENT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

guard RFID ST-4-WIFI Wi-Fi Staff Tag

FEATURES

Leverages Wi-Fi networks to provide real-time location information.
2 x configurable buttons
Built-in pull-duress alarm
Audio/visual indicators for motion and battery charging status
Includes wireless rechargeable battery
Over-the-air upgrades
Uses WPA2 to encrypt communication with system

DESCRIPTION

The ST-4-WIFI is a tag that is designed for locating, communicating and providing security to personnel. These tags leverage existing Wi-Fi networks to work with GuardRFID® exciters and AllGuard® software to determine the tag location in real-time. Each Wi-Fi Staff Tag has two configurable buttons and a built-in pull duress function that allows users to send alerts to the AllGuard system to help manage potentially hazardous situations.The tag can also receive alerts or acknowledgements from the AllGuard system and shows the notification through the indicator lights and/or sound on the tag.The Wi-Fi Staff Tag is powered by an internal, wireless rechargeable battery. To help extend battery life, the tag includes an internal motion detector to automatically adjust the beacon rate and manage power consumption. When you receive the tags, a tag activator may be needed to prompt each new tag to requestconfiguration settings from the AllGuard server. Subsequent configurations and firmware updates occur over-the-air using the Wi-Fi network.

SPECIFICATIONS

Product	ST-4- WIFI
Part Number	61-10402
Software Compatibility	AllGuard Server 6.5.0+
User Interfaces	2 x buttons (configurable), 2 x visual indicators, audio

transducer, pull duress alarm trigger
Sensors| Motion Detection, LF Receiver, Accelerometer

Operating Modes

| SAP : Standalone Access Point mode works with most Wi-Fi access points.

*contact GuardRFID for a list of compatible access points

CC X : Cisco Compatible Extension mode requires Cisco access points and supplementary equipment.

Wi-Fi Security| WPA2-PSK
Range| 30 m (100 ft) max. in a typical indoor healthcare environment
Transmit Frequency| 2.4GHz (802.11 b compliant)
Receive Frequency| 2.4GHz (802.11 b compliant), 125kHz

Battery Life

| Wireless recharging (6 hours for full charge)

(Battery life is dependent on use case and configuration.

The estimates below are based on typical usage for a Staff Duress solution.)

• SAP mode — typical 1 month before recharge

• CCX mode — typical 3 months before recharge

Beacon Interval

| Active / inside exciter field: 12 seconds, configurable

Static: configurable.

REQUIRED WI-FI RTLS LICENSES

Part Number: 62-50033

1-year Wi-Fi integration license for AllGuard software (annual)

Part Number: 62-40054

1-year Wi-Fi tag support license per tag (annual)

TAG ACTIVATOR

guard-RFID-ST-4-WIFI-Wi-Fi-Staff-Tag-
FIG2

Part Number: 61-20028

For configuring the Wi-Fi tags
Required for activating new Wi-Fi tags in a system

WI-FI TAG CHARGER

Part Number: 61-14024

For ST-4-WIFI tags
Can charge up to 10 tags at a time
Charge all tags within 6 hours
190.5 mm x 295.91 mm x 25 mm (7.50” x 11.65” x 0.98”)

FCC STATEMENT

This device complies with part 15 of the FCC Rules and with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Guard RFID Solutions Inc. sales@guardRFID.com • 866.785.7343