Hamaton 77-S253 FSK Sensor Installation Guide
- June 9, 2024
- Hamaton
Table of Contents
Hamaton 77-S253 FSK Sensor
CAP sensor install General
- Product Name: FSK Sensor
- Model Name: 77-S253
- Hardware Version: V1. 1
- Software Version: 020B
- Work temperature: -40℃——85℃
- FCC ID: 2AFH7-77S253
- IC: 23846-77S253
For the Hamaton Cap sensor installed on trailers/ trucks, the cap sensor is best installed onto one check port of hose. And its also could be installed on valve and air tank check port, we recommend to use 3N.m torque to tight the cap sensor onto the check port/ valves. If we installed on hose, we should keep the top of cap sensor towards the outside. orientation.
Recommended tools
- 3N.m standard torque tool.
- open end wrench, No.9 or 10.
Installation Process
- Taking off the valve cap for check port or valves.
- Fit the cap sensor onto check port or valves, and pre-twist 2 or 3 turns.
- Use standard 3N.m torque wrench tight the sensor onto valve check port.
Manufacturer Information
- HAMATON AUTOMOTIVE TECHNOLOGY CO. , LTD
- No. 122,Changda Road, Linping, Yuhang, Hangzhou, China
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions
- This device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The user that changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions
- This device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation of the device.
In additional, this device complies with ICES-003 of the Industry Canada (IC) Rules. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Industry Canada licence-exempt RSS standard(s). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The user that changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment.