SelectBlinds Cordless Roller Shades with Cassette Instructions

June 9, 2024
SelectBlinds

selectblinds logo

Select Blinds Cordless Roller Shades with Cassette

INSTALLATION

Fitting the bracketsSelectBlinds Cordless Roller Shades with Cassette
1

Fitting the blind

Holding the shade at an angle, hook the lip at the front of the headrail over the front hook of the bracket. Then, pushing back against the front of the headrail, raise the back of the headrail and push upwards until it snaps into place.SelectBlinds Cordless Roller Shades with Cassette
2To remove the shade from the brackets, push back against the front of the headrail and twist the back of the headrail downwards until it disengages from the brackets.

Operation and spring tension

The shade’s spring mechanism is locked with a locking pin to prevent it unrolling during transit. Before you operate the shade for the first time, locate the locking pin and simply pull it out to remove it.

If you find that over time the spring mechanism is weakening (in that the shade does not easily retract when you raise it) then the tension can be increased very easily. Take the shade down from the brackets and locate the tension screw at one end. Using a screwdriver, turn the screw in the direction of the front of the shade. This will increase the tension in the spring and allow the shade to retract more easily. Make small adjustments (around 2 turns at a time) to avoid over-tensioning the spring mechanism. Attach clear handle(s) to the bottom rail by carefully sliding on.

Fitting the brackets

The brackets offer 2 methods of installation:SelectBlinds Cordless
Roller Shades with Cassette 6

Fitting the blind

Holding the shade at an angle, hook the lip at the front of the headrail over the front hook of the bracket. Then, pushing back against the front of the headrail, raise the back of the headrail and push upwards until it snaps into place.SelectBlinds Cordless Roller Shades with Cassette
7

To remove the shade from the brackets, push back against the front of the headrail and twist the back of the headrail downwards until it disengages from the brackets.SelectBlinds Cordless Roller Shades with Cassette
8

Operation and spring tension

The shade’s spring mechanism is locked with a locking pin to prevent it unrolling during transit. Before you operate the shade for the first time, locate the locking pin and simply pull it out to remove it.

If you find that over time the spring mechanism is weakening (in that the shade does not easily retract when you raise it) then the tension can be increased very easily. Take the shade down from the brackets and locate the tension screw at one end. Using a screwdriver, turn the screw in the direction of the front of the blind. This will increase the tension in the spring and allow the blind to retract more easily. Make small adjustments (around 2 turns at a time) to avoid over-tensioning the spring mechanism. Attach clear handle(s) to the bottom rail by carefully sliding on.

Motorized Roller Shades with Cassette

The brackets offer two methods of installation:SelectBlinds Cordless Roller
Shades with Cassette 11

Note that the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.SelectBlinds Cordless Roller Shades with Cassette
12

FITTING THE SHADE:SelectBlinds Cordless Roller Shades with Cassette
13

Before you begin

SelectBlinds Cordless Roller Shades with Cassette 14

We will have positioned the controls where you requested during the ordering process. However if you decide to swap the side that they are on, direction of the roll or need to trim the blind further, the controls can be removed by simply unplugging them from the tube. This should be done prior to fixing the brackets.

Fitting the brackets

The brackets offer three methods of installation:SelectBlinds Cordless
Roller Shades with Cassette 15

Top Tip
Top-fixing or face-fixing are recommended for most installations, whereas side-fixing is only recommended if the width you gave us was taken right at the top of the recess.

Fitting the blinds

Locate the depression end (the opposite end to the controls) of the blind into the cross-shaped hole in the corresponding bracket.SelectBlinds Cordless
Roller Shades with Cassette 16Lift the control end of the blind and slot the rectangular ‘lugs’ into the corresponding slots on the bracket.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SelectBlinds User Manuals

Related Manuals