ergotron 47-093-800 100 Series Flat Panel Monitor Pivots User Guide
- June 4, 2024
- ERGOTRON
Table of Contents
100 Series Flat Panel Monitor Pivots
Vertical Surface, Direct Mount
User Guide
47-093-800 100 Series Flat Panel Monitor Pivots
Tools Needed
Learn more about ergonomic computer use at:
www.ergotron.com/ergonomics
Mounting Height for Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that
accommodates user heights of 5’5″ (162cm) when set up for standing and user
heights of 5’4” (165 cm) when set up for sitting. If user heights are
different than this, you should change the mounting height to accommodate user
heights.
(Change mounting height one inch for every one-inch difference in user
heights). Mounting height assumes there is a 6” (152 mm) distance between the
center of your monitor mounting holes and the top of the screen. If your
distance is smaller, you should increase the mounting height accordingly, if
your distance is larger, you should decrease your mounting height accordingly.
Determine Mounting Configuration
NOTE: Fasteners may unwind due to vibration caused by the movement of the mounting solution over time. Inspect mounting solutions for loose fasteners on a routine basis. If desired, apply a light-duty thread locking adhesive to fasteners before installation to prevent back-out.
Mount Pivot
Attach Monitor
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a diff erence. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Tilt — Forward and Backward
|
Increase Friction
If this product moves too easily, then you’ll need to increase friction:|
Decrease Friction
If this product is too diffi cult to move, then you’ll need to decrease
friction:
Pan — Side-to-side
|
Increase Friction
If this product moves too easily, then you’ll need to increase friction:|
Decrease Friction
If this product is too diffi cult to move, then you’ll need to decrease
friction:
Rotate — Portrait/Landscape
|
Increase Friction
If this product moves too easily, then you’ll need to increase friction:|
Decrease Friction
If this product is too diffi cult to move, then you’ll need to decrease
friction:
Safety
Warning: Because mounting surface materials can vary widely, it is imperative that you make sure the mounting surface is strong enough to handle mounted products and equipment.
Caution: Leave enough slack in the cable to allow a full range of motion.
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury.
Weight Capacity:
CAUTION: DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY OCCUR!
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE: When contacting customer service, reference the serial number.
www.ergotron.com
© 2010 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete information on the installation and use of its products, it will not be held liable for any editorial errors or omissions (including those made in the process of translation from English to another language), or for incidental, special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction. Ergotron, Inc. reserves the right to make changes in the product design and/or product documentation without notification to its users. For the most current product information, or to know if this document is available in languages other than those herein, please contact Ergotron. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan, Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc.
14 of 14 888-47-019-02 rev. T + 02/22
Documents / Resources
|
ergotron 47-093-800 100 Series Flat Panel Monitor
Pivots
[pdf] User Guide
47-093-800, 100 Series, Flat Panel Monitor Pivots, 47-093-800 100 Series Flat
Panel Monitor Pivots, Panel Monitor Pivots, Monitor Pivots, Pivots
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>