BIXOLON SRP-330/332III Network Connection Instructions

LAN Setting Values

Network

| Inactivity Time| TCP connection hold time| 0~3600 integer
IP Assignment

Method

| IP Assignment Method| DHCP/Manual
IP Address| Printer IP| IP Address
Subnet Mask| Subnet mask| IP Address
Gateway| Default Gateway| IP Address

For changing network setting values using Net configuration tool, Refer to ‘Net configuration tool manual’.

Ethernet Test by using Windows Test Page

You can use the Windows printer driver as shown below when there is no test program. Operating systems that allow you to use the Windows printer driver are Windows, XP, Server 2003, VISTA, 2008 Server, 7, 8, 10. You can download the latest version of Windows driver from our home page. (www.bixolon.com)

1. Double-click the Windows Driver installation file.

2. Click Install.

3. Select Installation and click Next.

4. Select Model Name and click Next.

5. Select Ethernet and click Add TCP/IP Port.

6. Enter the IP address and port number, and then click Next.

7. Click Next.

8. Click Next.

9. Click Next.

10. Click Finish.

11. Open the printer properties window in the Windows OS. Installing on Windows VISTA / Server 2008 / 7 / 8 / Server 2012 / 10
    ※ Control Panel – Hardware and Sound – Device and Printers.

12. In the Ports tab, click Configure Port.

13. 통신조건이 프린터와 일치되었는지 확인하십시오.

14. Click Print Test Page and check printing status. Proper installation of the driver is indicated if the test page is printed normally.

Factory Reset

Initializing LAN Setting

• This function changes the LAN settings of the printer to the initial factory settings.
• After the printer has finished booting, open the printer cover and press and hold the FEED Button for 5 seconds. This will cause the interface setting confirmation mode. Then add the paper, close the cover, and check that the following message is printed.

Checking Interface Setting

• 0: Exit
• 1: LAN Information Print
• 2: LAN Factory Reset and Reboot Printer
• 3 or more: None

Select Modes by Feed button control as below.

• Step 1. Short-press as many times as The mode number to choose.
• Step 2. Long-press over 1 second.

e.g. To choose Mode 2, press Feed Button 3 times(short-short-long)

If the above message is printed, select Mode 2, and you will see the following LAN data. (To select Mode 2, press the Feed button twice quickly/ once long.) After the above message is printed, the printer will automatically reboot.

LAN FACTORY RESET OK! Reboot Printer.

Factory Reset Values

LAN

| ****

Network

| Inactivity time| 0
---|---|---|---
IP Assignment

Method

| Automatic(DHCP)
Local Port| 9100

Troubleshooting

Check network

| of the printer and the AP (or wireless terminals) are the same.

The first three digits of the four digit value of the IP address

setting

(Refer to

| must be the same.
Configuration for| [Subnet Mask]
checking/changing| Check whether the subnet mask of the printer matches the
the printer

settings)

| one in AP (or wireless terminal).
 | [Port]

Check whether the port configured in the printer and the host

(PC, PDA) are the same.

PING Check

| [Checking IP collision]

When entering IP address manually without using DHCP, you must check whether the corresponding IP address is used by other equipment. The printer may not work normally when there is a collision in the IP address.

When the printer is turned off, carry out the Ping Test to the printer IP.

[Ping TEST]

1)   Turn off the printer.

2)   Select “Run” from the Windows Start menu, and then enter “cmd”.

3)   Enter “ARP –d” and delete ARP table.

4)   Enter “ping {printer IP}”.

5)   ARP –d, ping {IP address}

Network Connection Manual

 |

When you see “Request timed out.” as shown below, it means that there is no collision. The corresponding IP can be used.

On the other hand, if there is a reply as shown below, then the corresponding IP is used by another network terminal and it cannot be used for the printer IP.

---|---

Inactivity Time

| If multiple host devices are used with one printer, “Inactivity Time” is Recommended.

(Other host devices are restricted to use a printer if

one host device keep connecting to a printer.) ex) 5sec

Copyright

© BIXOLON Co., Ltd. All rights reserved.
This user manual and all property of the product are protected under copyright law. It is strictly prohibited to copy, store, and transmit the whole or any part of the manual and any property of the product without the prior written approval of BIXOLON Co., Ltd. The information contained herein is designed only for use with this BIXOLON product. BIXOLON is not responsible for any direct or indirect damages, arising from or related to use of this information.

• The BIXOLON logo is the registered trademark of BIXOLON Co., Ltd.
• All other brand or product names are trademarks of their respective companies or organizations.

BIXOLON maintains ongoing efforts to enhance and upgrade the functions and quality of all our products. In the following, product specifications and/or user manual content may be changed without prior notice.

http://www.bixolon.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>