HPS 57-1585 Performance Silicone Air Intake Tube Instruction Manual
- June 9, 2024
- HPS
Table of Contents
57-1585 Performance Silicone Air Intake Tube
Performance Silicone Air Intake Tube
Part Number: 57-1585
2018-2022 Lexus IS300 2.0L Turbo
2016-2017 Lexus IS200t 2.0L Turbo
2018-2019 Lexus GS300 2.0L Turbo
2016-2017 Lexus GS200t 2.0L Turbo
2016-2017 Lexus RC200t 2.0L Turbo
2018-2022 Lexus RC300 2.0L Turbo
Installation Instructions
For technical inquiries please email us at
tech@hpsperformanceproducts.com
In the email, please include the following information for faster response:
- Year / Make / Model / Engine of your vehicle.
- If it is a fitment issue, please include pictures showing the fitment problem.
- If there are missing parts, please list the part number(s) from the bill of materials on the 2nd page.
- Optional but recommended – Your contact phone number and preferred call back time.
You can also give us a call
via626-747-9200 for tech support
Monday-Friday, 9:00am-5:00pm
Pacific Time.
Last revision 10262021
Bill of Materials
Part Number: 57-1585
| Description | Prep | Part Number | Qty | Check |
|---|---|---|---|---|
| Silicone Tube | 1 | 57-1585 | 1 | |
| Worm Gear Clamp for Air Box | 2 | EMSC-70-90 | 1 | |
| Worm Gear Clamp for Throttle body | 2 | EMSC-50-70 | 1 | |
| Worm Gear Clamp for Breather Hose | 2 | EMSC-25-40 | 1 |
- Before installing any parts of this intake system, please read the instructions thoroughly.
- Verify the contents of this intake kit before disassembling your vehicle.
- DO NOT INSTALL IF ANY PARTS ARE MISSING OR DAMAGED. CONTACT tech@hpsperformanceproducts.com IMMEDIATELY. WE ARE NOT RESPONSIBLE FOR ANY DAMAGE CAUSED DUE TO IMPROPER INSTALLATION.
- Installation requires moderate mechanical skills. A qualified mechanic is highly recommended.
- Do not attempt to install the intake system while the engine is hot.
- This installation may require removal of coolant lines that may be hot.
- For technical inquiries, please e-mail us at tech@hpsperformanceproducts.com
PLEASE READ CAREFULLY BEFORE INSTALLATION!
This installation is not for the novice customer. Install this system with
EXTREME caution! Misuse of this product can destroy your engine! If you are
not well versed in the installation of intakes and if you are not mechanically
inclined, please have a tuner shop install this kit.
NOTE: HPS holds no responsibility for any engine damage that results from
misuse of this product.
GETTING STARTED
- Turn the ignition OFF and disconnect the vehicle’s negative battery cable. If the engine has run within the past two hours let it cool down.
NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code. We also highly recommend NOT discarding any stock parts after the installation.
Final Steps
Once the intake has been positioned, tighten all of the clamps and secure all
of the parts.
Upon completion of the installation, reconnect the negative battery terminal
before you start the engine. Double check to make sure everything is tight and
properly positioned before starting the vehicle.
Start the engine. Let the car idle for 3 minutes. Perform a final inspection
before driving the vehicle. Listen carefully for any odd noises, rattles
and/or air leaks prior to taking it for a test drive. If any problems arise go
back and check the vacuum lines, hoses and clamps that may be causing leaks or
rattles and correct the problem.
Periodically, recheck the alignment of the intake system and make sure there
is proper clearance around and along the length of the intake. Failure to
follow proper maintenance procedures may cause damage to the intake and will
void the warranty.