ekomia Levi Electric Height Adjustable Desk User Manual
- June 9, 2024
- ekomia
Table of Contents
ekomia Levi Electric Height Adjustable Desk
PARTS
TOOLS
Safety Information
-
Assembly and operation of the Levi must be in accordance with these assembly instructions otherwise there is a risk of injury!
-
The table support is solely intended to serve the purpose of ergonomic adjustments for your desk in accordance with the weights and measurements given in these instructions.
Any usage other than that mentioned above is inappropriate; the manufacturer disclaims liability for any resulting damages. In such cases all risk is carried by the user. -
Please also take into account the general legal and other regulations and legal provisions that are applicable including those that apply in the operator‘s country as well as the applicable environmental protection regulations. The regulations of trade associations or other supervisory authorities that are in force locally must always be observed!
-
The manufacturer cannot be held responsible for any losses or damage resulting from unauthorized modifications of the Levi. The power supply is to be used exclusively for Kesseböhmer guide columns!
-
Store the Assembly and Operation Instructions close to the device.
-
This appliance can be used by children aged from 14 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision. Do not leave children unattended with the table support. Children cannot estimate the danger of the force that the table support has. -
To avoid any danger of jamming or crushing it is necessary to keep a minimum distance of 25mm to the moving parts.
-
The assembly site should be dry, dust-free and without direct sunlight. Make sure that no liquid enters the column unit or power supply as this could cause electrical shock or short circuit!
-
The duty cycle of the system is set to 2 minutes “ON” and 18 minutes “OFF” or 0.5 minutes “ON” and 9 minutes “OFF”.
Power cables must not be pinched, bent, stretched or mechanically stressed! -
The socket for connection with the mains must be installed by a licensed electrician in order to avoid any hazard to persons or objects.
-
Load limits must not be exceeded.
-
Never open the housing of the power supply! Danger to the user can arise and the guarantee claim will expire as a result of unauthorized opening of the housing and improper repairs. Only the manufacturer’s service technicians are authorized to open or repair the electrical equipment!
-
In the event of a malfunction for example smoke, odors, unusual noises, or visible external damage switch off the system. Disconnect at the mains!
INSTRUCTION
Base Reset: Crushing and shearing hazard!
When restoring the control system to the factory settings and when resetting,
the collision protection ISP [Intelligent System Protection] is inactive
Make sure that no objects or persons are in the danger zone (safety distance >
25 mm) and that they do not reach into the danger zone.
Controller Functions
-
Save to memory: Press and hold M for 1 to 3 sec. Then press 1, 2, 3 or 4 within 3 sec.
Confirmation of the saved position by a double-clicking sound. -
Start from memory: Press 1, 2, 3 or 4 and hold until the desired position is reached (see height display).
-
Button lock on/off: Press and hold M for up to 10 sec.
-
Perform system reset: Repeat step 12 from initial assembly.
-
Change displayed height: Hold M for 5 sec until M is displayed on the screen. Then navigate the menu with up and down arrows until OFS is displayed. Press M to select and height display will flash. Adjust with arrows and confirm with M.
Error messages on the control display
The display reads HOT
| Cause | Remedy |
|---|
The control unit is fitted with overheating protection. Overheating has caused it to stop the control unit.| The control unit is fitted with overheating protection. Overheating has caused it to stop the control unit.
The display reads E + an error code
| Code / Description | Remedy |
|---|
00 Internal Error Channel 1
01 Internal Error Channel 2
02 Internal Error Channel 3
| Unplug the power cord and contact customer service
12 Defect Channel 1
13 Defect Channel 2
| Unplug the control unit. Fix the external short circuit.
OR
Plug in the correct motor to the motor socket that shows the error. Start the control unit again.
24 Overcurrent Motor M1
25 Overcurrent Motor M2
48 Overcurrent Motor Group 1
60 Collision protection
62 Overcurrent Control Unit
| Remove jammed objects from the driving area. Desk might be overloaded – Remove load from desk.
Contact customer service.
36 Plug detection in Motor socket M1
37 Plug detection in Motor socket M2
61 Actuator changed
| Plug in the correct motor to the motor socket that shows the error.
Reset all motors.
55 Synchronization lost motor group 1| Remove load from desktop. Reset
all motors. If error occurs after reset again, contact customer service.
67 High voltage| Unplug the power cord and contact customer service.
81 Internal error| Make a manual reset. Unplug the power cord and plug
in again after a few seconds.
If this error occurs frequently, unplug the power cord and contact customer service.
Additional Information
- The Levi adjustable base is designed to carry up to 130 kg in weight. The weight of the top used needs to be included in this.
- Intelligent System Protection (ISP) is an electronic state-of-the-art protection system. It also substantially reduces the risk of fingers being trapped or pinched. In spite of ISP being in place, there may still be a risk of pinching in exceptional cases, as it is not only the control unit, but also the interaction between the mechanical and electronic systems that is responsible for cutting out the motor. In addition, the mechanical components, motor and ambient conditions all affect cut-out sensitivity.
Disposal
Information on the disposal of electrical and electronic equipment in the European Union:
Within the European Union, the disposal of electrically operated equipment is governed by national regulations based on the EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). In accordance with this, the device must no longer be disposed of with municipal waste or household waste. The device is accepted free of charge at municipal collection points or recycling centers. Product packing consists largely of recyclable materials. Dispose of it in an environmentally friendly manner and bring it in for recycling.
+49 (0) 30 41 76 19 72
[email protected]