Barebones XH510G Shuttle XPC Slim User Manual
- June 9, 2024
- Barebones
Table of Contents
User Manual
For the : XH510G Series
XPC Installation Guide
Copyright
©2022 by Shuttle ® Inc.
All Rights Reserved. No part of this publication may be reproduced,
transcribed, stored in a retrieval system, translated into any language, or
transmitted in any form or by any means such as electronic, mechanical,
magnetic, optical, chemical, photocopy, manual, or otherwise, without prior
written permission from Shuttle ® Inc. Other brands and product names used
herein are for identification purposes only and may be trademarks of their
respective owners.
Disclaimer
Shuttle® Inc. shall not be liable for any incidental or consequential damages
resulting from the performance or use of this product.
Shuttle®Inc. makes no representation or warranty regarding the contents of
this ma-nual. Information in this manual had been carefully checked for
accuracy;however, no guarantee is given as to the correctness of the contents.
For continuing product improvement, Shuttle® Inc. reserves the right to revise
the manual or make changes to the specifications of this product at any time
without notice and obligation to any person or entity regarding such change.
The information contained in this manual is provided
for general use by customers. This device complies to Part 15 of the FCC
Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must withstand any background interference including those that may cause undesired operation.
Trademarks
Shuttle is a registered trademark of Shuttle Inc.
Intel and Pentium are registered trademarks of Intel Corporation.
PS/2 is a registered trademark of IBM Corporation.
AWARD is a registered trademark of Award Software Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
General Notice
Other brand and product names used herein are for identification purposes only
and may be trademarks of their respective owners.
Safety Information
Read the following precautions before setting up.
CAUTION
Incorrectly replacing the battery may damage this co-mputer. Replace only with
the same or equivalent type recommended by the manufacturer. Disposal of used
batteries according to the manufacturer’s instructions.
Installation Notices
Do not place this device underneath heavy loads or in an unstable position.
Do not expose this device to high levels of direct sunlight, high-humidity or
wet conditions.
Do not use or expose this device around magnetic fields as magnetic
interference may affect the performance of the device.
Do not block the air vents to this device or impede the airflow in any way.
Driver and Software Installation
Motherboard Driver DVD
The DVD contents attached in XH510G Series motherboard are subject to change
without notice.
!The Motherboard Driver DVD contains all the motherboard drivers necessary to
optimize the performance of this Shuttle Xvision in a Windows OS. Install
these
drivers after installing Microsoft ®
Insert the attached DVD into your DVD-ROM drive. The DVD AutoRun screen should
appear. If the AutoRun screen does not appear, double click on Autorun icon in
My Computer to bring up Shuttle Mainboard Software Setup screen.
Navigation Bar Description :
- Auto Install Driver
- Install Intel Rapid Storage Tech. Driver
- User Manuals – Motherboard Manual, Quick Guide.
- Link To Shuttle Website – Link to shuttle website homepage.
- Browse This DVD – Allows you to see contents of this DVD.
User Manuals
- Install Adobe Reader 9.5
- Motherboard Manual
- Quick Guide
Appendix
Starting BIOS
AMIBIOS has been integrated into many motherboards for over a decade. In the
past, people often referred to the AMIBIOS setup menu as BIOS, BIOS setup, or
CMOS setup.
American Megatrends refers to this setup as BIOS. Specifically, it is the name
of the AMIBIOS BIOS setup utility. This chapter describes the basic navigation
of the BIOS setup screens.
Enter the BIOS
To enter the BIOS setup screens, follow the steps below:
Step1. Power on the motherboard.
Step2. Press the
Step3. After you press the
This manual describes the standard look of the BIOS setup screen. The
motherboard manufacturer has the ability to change any and all of the settings
described in this manual. This means that some of the options described in
this manual do not exist in your motherboard’s AMIBIOS.
In most cases, the
BIOS Setup Menu
The main BIOS setup menu is the first screen that you can navigate. Each main
BIOS setup menu option is described in this user’s guide.
The Main BIOS setup menu screen has two main frames. The left frame displays
all the options that can be configured. “Grayed-out” options cannot be
configured.
Options is blue can be.
The right frame displays the key legend. Above the key legend is an area
reserved for a text message. When an option is selected in the left frame, it
is highlighted in white.
Often a text message will accompany it.
AMIBIOS8 has default text messages built into it. The motherboard manufacture
retains the option to include, leave out, or change any of these text
messages. They can also add their own text messages. Because of this, many
screen shots in this manual are different from your BIOS setup screen.
The BIOS setup/utility uses a key-based navigation system called hot keys.
Most of the BIOS setup utility hot keys can be used at any time during the
setup navigation process. These keys include
Hot Key | Description |
---|---|
→ Left ← Right | The Left and Right |
setup screen. For example: Main screen, Advanced screen, Chipset screen, and
so on.
↑ Up
↓ Down| The Up and Down
+- Plus/Minus| The Plus and Minus
Tab| The
F1| The
F4| The
ESC| The
Enter| The
Main Setup
When you first enter the BIOS Setup Utility, you will enter the Main setup
screen. You can always return to the Main setup screen by selecting the Main
tab. There are two Main Setup options. They are described in this section. The
Main BIOS Setup screen is shown below.
System Time/System Date
Use this option to change the system time and date. Highlight System Time or
System Date using the
The time is in 24-hour format. For example, 5:30 A.M. appears as 05:30:00, and
5:30 P.M. as 17:30:00.
** Advanced**
Select the Advanced tab from the BIOS setup screen to enter the Advanced BIOS
Setup screen. You can select any of the items in the left frame of the screen,
such as CPU Configuration, to go to the sub menu for that item.
You can display an Advanced BIOS Setup option by highlighting it using the
TPM Configuration
Security Device Support
This item allows user to enable/disable firmware TPM funciton.
- The choice: Enabled, Disabled.
- Power Management Configuration
Wake Up by USB (S3)
This item allows you to enable or disable system wake up by USB (S3).
The choice: Enabled , Disabled.
EuP Function
This item allows you to enable or disable system EuP function in S4/S5.
The choice: Enabled , Disabled.
Power-On after Power-Fail
This item allows you to set system power on automatically after AC power
restored.
The choice: Power On, Former-sts, Power Off, Power On by LAN, Power On by
RTC.
PowerOn by RTC Alarm
When enabled, System will wake on the hr::min::sec specified.
The choice: Enabled , Disabled.
Wake Up by i219
This item allows you to enable or disable system wake on by onboard i219 chip.
The choice: Enabled , Disabled.
- CPU Configuration
You can use this screen to select options for the CPU Configuration Settings. Use the up and downkeys to select an item. Use the and keys to change the value of the selected option. A description of the selected item appears on the right side of the screen. The settings are described on the following pages. An example of the CPU Configuration screen is shown below.
The CPU Configuration setup screen varies depending on the installed processor.
Intel(R) V. T.
When enable, a VMM can utilize the additional hardware capabilities provided
by vanderpool Technology.
The choice: Enabled , Disabled.
CPU support, item appear.
Active Processor Cores
This item allows you to determine how many cores to be enabled.
Intel® HT Technology
This item allows you to enable or disable Intel(R) HT Technology.
The choice: Enabled , Disabled.
C State Support
This item allows you to enable or disable CPU C State.
The choice: Enabled , Disabled.
EIST
This item allows you to enable or disable Enhanced lntel SpeedStep
Technology.
The choice: Enabled , Disabled.
Intel(R) Speed Shift Technology
This item allows you to enable or disable Intel(R) Speed Shift
Technology(ISST).
The choice: Enabled , Disabled.
Turbo Mode
This item allows you to enable or disable lntel®Turbo Boost Technology.
The choice: Enabled , Disabled.
The CPU Configuration setup screen varies depending on the installed
processor.
SATA Configuration
Onboard Device Configuration
High Definition Audio
This item allows you to enable or disable system High Definition Audio.
The choice: Enabled , Disabled.
Onboard i219 Function
This item allows you to enable or disable i219 Function.
The choice: Enabled , Disabled.
Onboard LAN Boot ROM
This item allows you to enable or disable Onboard LAN Boot ROM.
The choice: Enabled , Disabled.
PCIeX16,X1 Speed
This item allows user to select PCIe Speed.
The choice: Auto, Gen1, Gen2, Gen3, Gen4.
PCIeX16 Gen4 is only for 11th Core i CPU family.
Initiate Graphic Adapter
Select which graphics controller to use as the primary boot device. Set
Initiate Graphic Adapter to “HG” and enable Multi-Monitor feature.
The choice: PCIE, onboard, HG.
IGD Memory Size Select
Allows you to select the size of system memory used by the internal graphics
device.
The choice: 32MB, 64MB, 128MB, 256MB, 512MB.
Intel(R) VT-d
This item allows you to enable or disable VT-d.
The choice: Enabled , Disabled.
Serial Port Configuration
Option are in its sub-menu.
Press
Serial Port 1
This item allows you to enable or disable Serial Port.
- The choice: Enabled, Disabled.
- Hardware Health Configuration
FAN1 Speed Control
This item allows you to set CPU Fan Speed.
- The choice: Smart Fan Mode, Ultra-Low Speed, Low Speed, Mid Speed, Full Speed.
Security
Select the Security tab from the BIOS setup screen to enter the Security BIOS
Setup screen. You can display an Security BIOS Setup option by highlighting it
using the
Supervisor Password
Indicates whether a supervisor password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.
User Password
Indicates whether a user password has been set. If the password has been
installed, Installed displays. If not, Not Installed displays.
Change Supervisor Password
Select Change Supervisor Password from the Security Setup menu and press
Enter New Password:
Type the password and press
Password Login control
This item allows user to adjust Password Login control.
- The choice: Setup, Boot, Both.
Flash Write Protection
Choose [Enabled] to avoid virus destroy BIOS. If you want to flash BIOS, you
must set it [Disabled].
The choice: Enabled or Disabled.
Secure Boot control
This item allows you to enable or disable Secure Boot.
- The choice: Enabled or Disabled.
Boot
Select the Boot tab from the BIOS setup screen to enter the Boot BIOS Setup
screenYou can select any of the items in the left frame of the screen, such as
Boot Settings
Configuration, to go to the sub menu for that item.
You can display an Boot BIOS Setup option by highlighting it using the
All Boot BIOS Setup options are described in this section.
The Boot BIOS Setup screen is shown below. The sub menus are described on the
following pages.
Bootup Num-Lock
This item allows you to enable or disable keyboard Num-Lock state.
- The choice: Enabled, Disabled.
Boot from USB device
This item allows you to enable or disable boot from USB device.
- The choice: Enabled , Disabled.
Fast Boot Function
This item allows you to enable or disable Fast Boot Function.
- The choice: Enabled , Disabled.
Boot Device Priority (Boot Option #1/2/3/….)
Specifies the boot sequence from the available devices. A device enclosed in
parenthesis has been disabled in the corresponding type menu.
Save & Exit
Select the Exit tab from the BIOS setup screen to enter the Exit BIOS Setup
screen.
You can display an Exit BIOS Setup option by highlighting it using the
All Exit BIOS Setup options are described in this section.
The Exit BIOS Setup screen is shown below.
Save Changes and Exit
When you have completed the system configuration changes, select this option
to leave BIOS Setup and reboot the computer so the new system configuration
parameters can take effect.
Select “Save Changes and Exit” from the Exit menu and press
Save Configuration Changes and Exit Now?
[Ok] [Cancel] appears in the window. Select Ok to save changes and exit.
Exit Without Saving Changes
Select “Exit without Saving Changes” from the Exit menu and press
Load Defaults Settings
BIOS automatically sets all BIOS Setup options to a complete set of default
settings when you Select this option. The Optimal settings are designed for
maximum system performance, but may not work best for all computer
applications. In particular, do not use the Optimal BIOS Setup options if your
computer is experiencing system configuration problems. Select Load Optimal
Defaults from the Exit menu and press
Select Ok to load optimal defaults.
H510G
|
(Pb)| (Hg)| (Cd)| (Cr(VI))| (PBB)| (PBDE)
| X| O| O| O| O| O
| O| O| O| O| O| O
| X| O| O| O| O| O
| X| O| O| O| O| O
| O| O| O| O| O| O
| X| O| O| O| O| O
SJ/T 11364
OT 26572
X:T 26572
T 26572
Address : 5F, NO.30, Lane 76, Rui Guang Rd., Nei-Hu Dist., Taipei, Taiwan.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>