LASENCHOO 8 Lights Modern Chandelier Light Fixture Instruction Manual
- June 9, 2024
- LASENCHOO
Table of Contents
LASENCHOO 8 Lights Modern Chandelier Light Fixture
TIPS
Dear customer: Thank you for choosing our products. Please read this manual
carefully before installation. If there is any problem during installation,
please contact us as soon as possible.
Installation
- Please read this manual carefully before installation.
- Only a professional electrician should install this fixture.
- Please make sure that the electricity is powered off before installation.
- If there are any questions or problems during installation, please don’t hesitate to contact us to get professional suggestions or video.
- Please check the fixture after installation finished, if the light is very weak or flickers, it might be wrong connection of live wire and neutral wire, please make sure the connection is correct to avoid damage of the fixture.
Working Environment
- Please install this fixture only dry location.
- Allowed maximum wattage for single bulb is 60W, please do not use bulb more than this wattage.
- Please do not turn on / turn off the fixture frequently, which is very easy to destroy the fixture.
Maintenance
- Please use only dry & dust-free fabric to clean the fixture.
- Take a picture before remove out the parts for memory reminder, it will really help you to assemble the fixture correctly after cleaning.
- Do not modify or exchange the parts of the fixture to avoid damage.
- Do not use any liquid such as water or detergent to do cleaning, which will damage the finishing of the fixture.
- If there any abnormal of the fixture, please cut off the power immediately and ask help to a professional technician.
Specification
| Name | D0070-6 / D0070-8 |
|---|---|
| Material | Iron |
| Finishing | Painting |
| Dimension | Diameter: 26.2inch(66cm) Height:27.6inch(70cm) |
| Height | Height adjustable from 27.6 to 66.9 inch(70 to 170cm) |
| Weight | D0070-6:5.73pound(2.6kg) / D0070-8:6.39pound(2.9kg) |
| Bulb Base | E12 |
| Wattage | Maximum 60W per bulb |
| Voltage | 110V |
| Bulb | LED / Edison / CFL / Incandescent / Halogen |
| Dimmable | Working with dimmer |
| Roof | Flat / Sloping / Vaulted Ceiling |
| Working Space | Indoor 20-50m² |
| Suitable Area | Living Room / Dinning Room / Kitchen / Bedroom / Reading Room / |
Entryway / Foyer / Hallway
Package List
Installation Steps
- Install the arms 2 on the top plate 1 by lock nut and teeth lock washer 3.
- Connect all the wires by parallel with connectors 4 (all live line-L use one connector, and neutral Line-N use another connector).
How to use the splicing connector:
- Cut into the wire’s insulation 10mm without cutting the wire, and then pull toward end of wire to remove the insulation.
- Pull the orange operating handle A to open the inlet hole 90°, insert the wire B into end of the hole, press the operating handle A and check the wire can not pull out any more, then wiring finish.(Note one inlet hole accepts 0.08-2.5mm² wire, so can insert 2-3 wires into one inlet hole)
note:
- The operating handle A must keep 90°when is open, and carefully your finger that to avoid hurting when close the handle A.
- The splicing connector is working by parallel wire connection, so one connector only can connected all live wire or all neutral wire, can not mix live wire and neutral wire in one connector.
How to use the cap connector
- Prepare the bare ends of the wires and tidy them up, twining the bare ends together.
- Place the plastic wire cap onto the ends of the wires, rotate the wire cap clockwise to make the wires can not pull out then finishing wiring, after that use lock tie to make the wires fixed.
note:
- The cap connector is working by parallel wire connection, so one connector only can connected all live wire or all neutral wire, can not mix live wire and neutral wire in one connector.
- Suggestion : when finish wiring, use electrical tape for each connector cap onto its respective wire.
- Install the metal box 5 to the plate 1 with end cap 6.
- Let the wire go through the tube 7 and tube 8 rotate to fasten the tubes on the fixture.
- Let the wire go through the ring 10 of hanging chain 9, rotate the ring 10 to fixed the chain 9 on the fixture, connect the chain 9 with canopy 11 by carabiner hook screw connection 12, let the wire go through the chain 9 and canopy 12.
- Install the bracket 13 to the ceiling junction box with screw.
- Connect the wire with connector 14 to your home line.
- Install the fixture to the bracket with cap nuts 15.
- Put the cylinder tube 16 on the bulb holder and after that install the bulbs 17.
Thank you again for your support and trust. Best wishes for you！
Read User Manual Online (PDF format)
Loading......