ANGELES HOME 8CK-65HW716WH 41 Inch L White Rectangle Wood Lift Top Coffee Table Instructions
- June 9, 2024
- ANGELES HOME
Table of Contents
ANGELES HOME
8CK-65HW716WH 41 Inch L White Rectangle Wood Lift Top Coffee Table
Instructions
Before You Start
Read each step carefully before starting. It is very important to ensure each
step followed in correct order, otherwise assembly difficulties may occur.
Most of board parts are labeled or stamped on the raw edges. Have a check to
make sure all parts are included.
Work in a spacious area, preferably on a carpet close to where the unit will
be used.
Keep the handtools close at hand. Do not use power tools to assemble your
furniture. They may scratch or damage the parts.
Board Identification
Not actual size
STEP 1
Install 4 pcs dowels (A) and 4 pcs cam pins (B) to End panel (2)
Part A x 4 Part B x 4 Part 2 x 1| STEP 2
Install 4 pcs dowels (A) and 4 pcs cam pins (B) to End panel (3)
Part A x 4 Part B x 4 Part 3 x 1
---|---
|
STEP 3
Install 8 pcs dowels (A) to Between panel (4)
Part A x 8 Part 4 x 2| STEP 4
Install 4 pcs cam pins (B) to 2 Brace panels (5)
Part B x 4 Part 5 x 2
|
STEP 5
Install 8 pcs dowels (A) and 4 pcs cam pins (B) to Middle panel (6)
Part A x 8 Part B x 4 Part 6 x 1| STEP 6
Install 4 pcs dowels (A) and 4 pcs cam pins (B) to Bottom panel (7)
Part A x 4 Part B x 4 Part 7 x 1
|
STEP 7
Install 4 pcs dowels (A) to 2 Solid Panels (8)
Part A x 4 Part 8 x 2| STEP 8
Install 10 pcs cam pins (B) to 2 Legs (9)
Part B x 10 Part 9 x 2
|
STEP 9
Install 8 pcs cam pins (B) to 2 Legs (10)
Part B x 10 Part 10 x 2| STEP 10
Install one Front Leg (9) and one Rear Leg (10) to End panel (2)
and lock with 4 pcs Cam locks (C)
Part C x 4
|
STEP 11
Install one Front Leg (9) and one Rear Leg (10) to End panel (3)
and lock with 4 pcs Cam locks (C)
Part C x 4| STEP 12
Install lever (11) to End panel (2) with 8 pcs Screws (E4)
Part E4 x 8
Part 11 x 1
|
STEP 13
Install lever (12) to End panel (3) with 8 pcs Screws (E4)
Part E4 x 8 Part 1 2 x 1| STEP 14
Attach 2 Brace panels (5) to Middle panel (6) and lock with
4 pcs Cam locks (C)
Part C x 4
|
STEP 15
Install 2 Support panels (8) to Bottom panel (7) with 16 pcs Screws (E4)
and reinforce with 4 sets of Corner brackets (S1) (S1 has equipped with self-
tapping screws with no drilling holes)
Part E4 x 16 Part S1 x 4| STEP 16
Install 2 Between panels (4) to the middle of Solid panel (6) and Solid panel
(7), then lock with 8 pcs Cam locks (C)
Part C x 8
|
STEP 17
Integrate End panel (2), (3) and the table legs with the main body, then
secure with 20 pcs Cam locks (C)
Part C x 20| STEP 18
Stick 40 pcs Cam covers (P) on Cam locks (C) and stick 6 pcs (M1) to the
corresponding places shown in the figure.
Part M1 x 6
Part P x 40
|
STEP 19
Install the Top panel (1) to the lifters (11), (12) with 12 pcs Screws (E4)
Part 1x 1 Part E4 x 12|
TIPS
Installation of cam pin and cam lock
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting. Use of
furniture polish is not necessary. Should you choose to use polish, test first
in an inconspicuous area. Using solvents of any kind on your furniture may
damage the finish. Never use water to clean your furniture as it may cause
damage to the finish. Liquid spills should be removed immediately. Using a
soft clean cloth, blot the spill gently. Avoid rubbing. Check bolts/screws
periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme
temperature and humidity changes can cause fading, warping, shrinking and
splitting of wood. It is advised to keep furniture away from direct sunlight
as sun may damage the finish. Proper care and cleaning at home will extend the
life of your purchase. Following these important and helpful tips will enhance
your furniture as it ages.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>