BRASSELER 7001800CM3000 Weather Station Wall Clock MyTime Jumbo Instruction Manual
- June 9, 2024
- BRASSELER
Table of Contents
- BRASSELER 7001800CM3000 Weather Station Wall Clock MyTime Jumbo
- About this Instruction Manual
- General Warnings
- Cleaning and Maintenance
- General information
- Scope of delivery (Fig. 1)
- Parts overview (Fig. 2 and 3)
- Getting started/Power supply
- Time setting
- Temperature and humidity display
- Troubleshooting
- Warranty & Service
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BRASSELER 7001800CM3000 Weather Station Wall Clock MyTime Jumbo
About this Instruction Manual
Please read the safety instructions and the operating instructions carefully
before use. Keep these instructions for renewed use at a later date. When the
device is sold or given to someone else, the instruction manual must be
provided to the new owner/user of the product.
Intended Use
This product is intended only for private use. The device is intended only for
indoor use.
General Warnings
DANGER!
-
Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.
-
This device contains electronic components that operate via a power source (batteries).
Children should only use the device under adult supervision. Only use the device as described in the manual; otherwise, you run the risk of an electric shock. -
Do not expose the device to high temperatures.
Use only the recommended batteries.
Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.
ATTENTION!
-
Do not immerse the unit in water.
-
Do not subject the unit to excessive force, shock, dust, extreme temperature or high humidity, which may result in malfunction, shorter electronic life span, damaged batteries and distorted parts.
RISK of property damage! -
Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
-
Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. Remove the batteries from the unit if it has not been used for a long time.
-
The manufacturer is not liable for damage related to improperly installed batteries!
EC Declaration of Conformity
Bresser GmbH has issued a “Declaration of Conformity” for this device (Wall
Clock / Art.No.: 7001800) in accordance with applicable guidelines and
corresponding standards of Directive 2014/53/EU.
This declaration is available under
http://www.bresser.de/download/7001800/CE/7001800_CE.pdf
UKCA Declaration of Conformity
Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with
applicable guidelines and corresponding standards. The full text of the UKCA
declaration of conformity is available at the following internet address:
www.bresser.de/download/7001800/UKCA/7001800_UKCA.pdf
Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8
6HF, Great Britain
Cleaning and Maintenance
- Before cleaning the device, disconnect it from the power supply (Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
- Protect the device from dust and moisture. The batteries should be removed from the unit if it has not been used for a long time.
Disposal
Dispose of the packaging materials properly, according to their type, such as
paper or cardboard. Contact your local waste-disposal service or environmental
authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per Directive 2012/19/EC of the European Parliament on waste electrical and
electronic equipment and its adaptation into German law, used electronic
devices must be collected separately and recycled in an environmentally
friendly manner.
In accordance with the regulations concerning batteries and rechargeable
batteries, disposing of them in normal household waste is explicitly
forbidden. Please make sure to dispose of your used batteries as required by
law — at a local collection point or in the retail market. Disposal in
domestic waste violates the Battery Directive.
General information
This item is available in the following variants. The functions and technical data are the same for all models. They only differ in its design/in its colour.
- Model 7001800CM3000: black
- Model 7001800GYE000: white
- Model 7001800QT5000: gray
Scope of delivery (Fig. 1)
Wall clock (A), Remote sensor (B), Instruction manual
Required batteries: 4 x 1.5V battery (Size AA/LR6) and 2 x 1.5V battery (Size
AAA/LR03) Batteries are not included.
Parts overview (Fig. 2 and 3)
Wall clock (Fig. 2)
-
Current time
-
Symbol for active alarm
-
Symbol for active snooze
-
Symbol for RCC signal reception
-
Humidity indoors (%)
-
Battery status indoors
-
Temperature indoors (°C or °F)
-
Humidity outdoors (%)
-
Temperature outdoors (°C or °F)
-
MEMORY button
-
SNOOZE button
-
SET button
-
Current date
-
Weekday
-
Wall mount
-
UP button
-
DOWN button
-
RESET button
-
Battery compartment
-
Stand (fold-out)
Remote sensor (Fig. 3) -
Indicator light
-
Wall mount
-
Battery compartment
Getting started/Power supply
NOTE!
Before operating the device or when replacing the batteries, make sure to
place the batteries strictly according to the right polarities (+/-) as shown
in the battery compartment.
- Remove the cover from the wall clock battery compartment (19).
- Insert the batteries (4x 1.5V, AA/LR6) into battery compartment (19).
- Wait until the indoor temperature will be displayed.
- Remove the the cover of the remote sensor’s battery compartment (23) .
- After the indoor temperature has been displayed, insert the batteries into the remote sensor and replace the cover.
- During the installation process, place the remote sensor next to the base unit. Only position the remote sensor and the base unit at the desired place after a successful installation process and position it within the effective transmission range.
Time setting
NOTE!
After the clock received the DCF time signal the time will be set according to
the Central European time (CET). Summer and winter time change (and reverse)
is also set automatically. Other deviating times can be set manually only.
Automatic time setting via DCF time signal After inserting the batteries the
time will be set automatically via DCF signal. This process may take a few
minutes.
Initiate to receive the DCF time signal manually
NOTE!
Use this function when e.g. automatic summer/ winter time change does not work
or the wall clock temporarely receives no time signal.
- Press and hold the DOWN button (17) for 3 seconds to start manual search for the DCF signal.
- Wait approx. 2-5 minutes until the current time will be displayed.
- If the signal for daylight saving time is received ‘DST’ will be displayed.
Manual time setting
NOTE!
It is necessary to set the time manually in places where no radio signal is
received.
If automatic radio signal reception is enabled, the functions of all buttons,
except SNOOZE and DOWN, are disabled. In this case press and hold the DOWN
button (17) for approx. 5 seconds until the LED km/h symbol disappears.
Automatic signal reception is now disabled
- Press and hold the SET button (12) in normal time display mode for approx. 3 seconds to change to time setting mode. Year figure flashes.
- Press the UP (16) or DOWN button (17) to change the value.
- Press the SET button (12) again to switch to the next setting.
- Repeat steps 2 and 3 to set other values in the following sequence: Year > Month > Day > 12/24 hour mode > time zone (+/- 12 hours) > Hours > Minutes > Weekday language
- After setting the value for the minutes press SET button (12) again to save and exit time setting.
Alarm time setting
- Press SET button (12) once switch to alarm time display. The currently selected alarm time will be displayed with AL.
- In alarm time display mode press and hold the SET button (12) for approx. 3 seconds to switch to alarm time setting mode. Hour figure flashes.
- Press the UP (16) or DOWN button (17) to change the value.
- Press the SET button (12) again to switch to the next setting.
- Repeat steps 2 and 3 to set other values in the following sequence: Minutes > Snooze interval (1 to 20 minutes)
- After setting the value for the snooze interval press SET button (12) again to save and exit alarm time setting.
- Press the UP button in alarm time display mode to enable or disable the alarm. Once the alarm has been activated, the symbol will be displayed.
NOTE!
Press the SNOOZE button when the alarm sounds to interrupt the alarm for the
desired snooze interval.
Press any button, except SNOOZE, to stop the alarm.
Temperature and humidity display
After inserting the batteries indoor humidity (5) and indoor temperature (7)
will be displayed. After first data transmission from the remote sensor the
outdoor temperature (9) will be displayed.
This process may take a few minutes.
- You can switch the temperature display from degree Celsius to degree Fahrenheit by pushing the DOWN button (17) at the backside of the wall clock.
- Press the MEMORY button (10) several times to display one after another the saved maximum, minimum and current values for temperature and humidity.
- Press and hold the MEMORY button (10) for approx. 3 seconds during maximum value display to delete all saved values.
Mounting/Positioning
NOTE!
Make sure you have mounted or placed the device in a safe way. Otherwise the
device may fall down and heavy damages can occur for which the manufacturer is
not liable.
The wall clock and the remote sensor can be mounted on walls with the wall
mount (9/16). Moreover they can be placed on plane surfaces with the fold-out
table stand (14/18).
Troubleshooting
Signal disconnection
If without obvious reasons the display of the outdoor temperature goes blank,
please check the following:
-
The remote unit is still in place.
-
The batteries of both the remote unit and main unit are not empty. Replace batteries with new ones if necessary.
NOTE!
When the temperature falls below freezing point, the batteries of outdoor units will freeze, lowering their voltage supply, effective range, and life span. -
All units required are within range and the path is clear of obstacles and interference. Shorten the distance if necessary.
Transmission collision
Signals from other household devices, such as door bells, home security
systems and entry controls, may interfere with those of this product and cause
temporarily reception failure. This is normal and does not affect the general
performance of the product. The transmission and reception of temperature
readings will resume once the interference recedes.
Other malfunctions
If there is no response from the wall clock by keystrokes or if any other
malfunctions occur perform the following steps.
NOTE!
With this procedure all received data will be deleted.
- Press RESET button (18) with a pointed instrument (e.g. pen).
- Wait approx. 2-5 minutes until the current time will be displayed.
Warranty & Service
The regular guarantee period is 5 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms.
References
- art.no
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- index · powered by h5ai 0.26.1 (http://larsjung.de/h5ai/)
- Bresser | BRESSER MyTime Jumbo LCD Wetter-Wanduhr | Expand Your Horizon
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>