Yorkville PS12S Parasource Series Powered Subwoofer Owner’s Manual

Yorkville PS12S Parasource Series Powered Subwoofer

IMPORTANT SAFETY INSTRUCTIONS

This lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The DO NOT STACK symbol is intended to alert the user that the product shall not be vertically stacked because of the nature of the product.

FOLLOW ALL INSTRUCTIONS

Instructions pertaining to a risk of fire, electric shock, or injury to a person

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THIS DEVICE IS FOR INDOOR USE ONLY!
INSTALLED BATTERY PACKS SHALL NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE, FIRE OR THE LIKE.

Read Instructions: The Owner’s Manual should be read and understood before operation of your unit. Please, save these instructions for future reference and heed all warnings.

Cleaning: Clean only with dry cloth.

Packaging: Keep the box and packaging materials, in case the unit needs to be returned for service.

Warning: To reduce the risk or fire or electric shock, do not expose this apparatus to rain or moisture. Do not use this apparatus near water!

Warning: When using electric products, basic precautions should always be followed, including the following:

Power Sources
Your unit should be connected to a power source only of the voltage specified in the owners manual or as marked on the unit. This unit has a polarized plug. Do not use with an extension cord or receptacle unless the plug can be fully inserted. Precautions should be taken so that the grounding scheme on the unit is not defeated. An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective earthing connection. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

Hazards
Do not place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious personal injury and serious damage to the product. Use only with cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. Only use attachments/accessories specified by the manufacturer.

Equipment that is suspended overhead must use a secondary safeguard to prevent personal injury in the event the primary mounting mechanism fails. Safety eyebolts attached to the equipment and galvanized steel wire can be used together to implement a failsafe mounting thus ensuring the safety of the equipment and anyone positioned below the equipment.
Improper installation can result in bodily injury or death. If you are not qualified to attempt the installation get help from a professional structural rigger.

Note: Prolonged use of headphones at a high volume may cause health damage to your ears.
The apparatus should not be exposed to dripping or splashing water; no objects filled with liquids should be placed on the apparatus.
Terminals marked with the “lightning bolt” are hazardous live; the external wiring connected to these terminals require installation by an instructed person or the use of ready made leads or cords.

Ensure that proper ventilation is provided around the appliance. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

Power Cord
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. The AC supply cord should be routed so that it is unlikely that it will be damaged. Protect the power cord from being walked on or pinched particularly at plugs. If the AC supply cord is damaged DO NOT OPERATE THE UNIT. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. The mains plug of the power supply cord shall remain readily operable.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Service
The unit should be serviced only by qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, requires battery pack replacement or has been dropped. Disconnect power before servicing!

The Lightning Flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prongs are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING:

• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
• To completely disconnect this apparatus from the ac mains, disconnect the power supply cord plug from the ac receptacle.
• The mains plug of the power supply cord or appliance coupler shall remain readily accessible.

CAUTION
TO PREVENT ELECTRIC SHOCK HAZARD, DO NOT CONNECT TO MAINS POWER SUPPLY WHILE GRILLE IS REMOVED.
PS12s, PS15s and PS18s
Congratulations on your purchase of a Parasource Series subwoofer, the best option when adding a subwoofer to Yorkville Sound’s Parasource Series powered speaker enclosures. The PS12s, PS15s and PS18s are premium-quality subwoofers with integrated power amplifiers.

Input Mode Switch

The line-level position is used when the PS12s, PS15s and PS18s are fed a signal from a processor, electronic crossover, the output of an un-powered mixer or the loop-through of a powered speaker cabinet. When in line-level mode, using balanced ¼-inch (Tip, Ring, Sleeve) and/or XLR cables will reduce the unit’s sensitivity to hum and buzz.

For speaker level operation, connect the PS12s, PS15s and PS18s just like an ordinary speaker (in parallel using the loop-through jacks) along with the passive full-range loudspeakers. The speaker level position should be used when the PS12s, PS15s and PS18s are fed with a ¼-inch speaker cable directly from the output of an
amplifier or a powered-mixer. You can also use a speaker level signal from the parallel connection on an un-
powered speaker cabinet.

WARNING:

• Do not plug in two speaker level sources to a single ES Series Powered Subwoofer!
• Increasing the Level control while in limiting will not increase the loudness and may lead to feedback when the operating level is reduced.

The PS12s, PS15s and PS18s’ Level Control

The Level control adjusts the amount of bass added to the sound system by the Parasource subwoofer. This control adjusts for the relative sensitivity of the companion full-range loudspeakers and the desired system frequency response. This control should be set by listening with a medium-level input signal (such that the limiter is not firing).

Note: It’s not recommended to set this control at high levels since the limiter will then greatly affect the output level.

Note: Setting the PS12s, PS15s and PS18s Level control at the center detent is the correct starting point when setting up a sound system. From there, adjustments can be made for the best sound. The detent is the setting that will give full power when the line input is used and the input signal is at a level of +3 dBv.

Input (Link) Jacks

The inputs are designed to make it easy to hook up your PS12s, PS15s and PS18s to almost any audio system with minimal hassle. An external crossover is not necessary and connections can be made using the ¼-inch and/or the XLR inputs and Thru connections.
The PS12s, PS15s and PS18s may be plugged in before or after the full-range loudspeakers, they do not alter the signal to the daisy-chained (thru) loudspeakers and will not draw any power from the host amplifier/ processor driving them.

Note: As well as accommodating full-range loudspeakers, the Thru jacks allow many PS12s, PS15s and PS18s subwoofers to be connected in a string (parallel). There is no practical limit to the number of PS12s, PS15s and PS18s subwoofers that may be connected together.

Protection

The PS12s, PS15s and PS18s are protected against excess driver excursion and against voice coil overheating. Please ensure that the line/speaker switch is in the correct position to prevent clipping of the input circuitry. The PS Series Powered Subwoofers have a DSP-based circuit to prevent clipping, over power and over excursion. For the best results, set the system so that the limiter LED occasionally lights up Red and is NOT Yellow all the time. Limiter LED lights Red when the excess driver excursion is active, this keeps the dynamics of the music. When the limiter LED is Yellow the voice coil overheating protection is active, this will compress the dynamics of the music. At high levels the limiter will limit the gain of the PS Series Powered Subwoofer and hence if the user attempts to set the subwoofer level control at a high level, the resulting setting will be overridden by the internal protection. The level control should be set while operating at low levels (under 10 watts). This is accomplished by turning the master volume of the signal going to the subwoofer down to allow the balancing and setting of the bass along with the full range speaker top in use. If the level control is set too high due to setting it at high operating levels the input circuit will clip and the dynamics of the bass will be lost. The Red Clip indicator will signify when this occurs. This can happen without audible distortion since the filters and limiters will suppress the distortion.

Note: At high power levels, when the limiter is operating, increasing the Subwoofer’s Level Control will NOT increase the output. Do NOT continue to increase this setting while operating at high levels.

Stand Mounting Adapter
The PS Series Powered Subwoofers come equipped with a built-in stand mounting adapter that can be used with Yorkville SW Teletube accessory to support powered top cabinets.

WARNING: PS Series Powered Subwoofers MUST be on a flat, level surface to support the cabinet safely. Do not use larger than the recommended top cabinets!

PS12S| Specifications
PS15S| PS18S
---|---|---
Active or Passive| Active| Active| Active
Program Power (watts)| 900 watts Program (1800 watts Peak)| 1000 watts Program (2000 watts Peak)| 1200 watts Program (2400 watts Peak)
Max SPL (dB)| 129dB Peak (123dB Continuous)| 132dB Peak (126dB Continuous)| 135dB Peak (129dB Continuous)
Frequency Response (Hz +/- 3dB)| 45Hz – 100Hz| 45Hz-100Hz| 45Hz-100Hz
Crossover Frequency (Hz)| fixed @ 100Hz| fixed @ 100Hz| fixed @ 100Hz
Driver Configuration| 1×12-inch (Bass Reflex Cabinet)| 1×15-inch (Bass Reflex Cabinet)| 1×18-inch
LF Driver(s)| 1×12-inch Long Throw Ceramic w/ 3-inch Voice Coil| 1×15-inch Long Throw Ceramic w/ 3-inch Voice Coil| 1×18-inch Ceramic w/ 4-inch Voice Coil
Inputs| XLR Balanced Line Level Input| XLR Balanced Line Level Input| XLR Balanced Line Level Input
| ¼-inch Line or Speaker Level Input| ¼-inch Line or Speaker Level Input| ¼-inch Line or Speaker Level Input
Outputs| XLR Balanced Link Output| XLR Balanced Link Output| XLR Balanced Link Output
| ¼-inch Link Output| ¼-inch Link Output| ¼-inch Link Output
Controls| Output Level, Line/Speaker Level Switch| Output Level, Line/Speaker Level Switch| Output Level, Line/Speaker Level Switch
| Power/Limit/Clip LED’s| Power/Limit/Clip LED’s| Power/Limit/Clip LED’s
Enclosure Materials| 15mm Birch| 15mm Birch| 15mm Birch
Baffle Material| 15mm Birch| 15mm Birch| 15mm Birch
Covering / Finish| Paint| Paint| Paint
Power Consumption (typical)| 230V~ 50 Hz 1.5A / 120V~ 60 Hz 3.0A| 230V~ 50 Hz 1.6A / 120V~ 60 Hz 3.2A| 230V~ 50 Hz 1.8A / 120V~ 60 Hz 3.6A
Dimensions (DWH xbackW, inches)| 22.8 x 14.7 x 16.85| 24 x 17.4 x 20| 22.25 x 21.25 x 32.25
Dimensions (DWH xbackW, cm)| 57.9 x 37.4 x 42.8| 61 x 44.2 x 50.8| 56.5 x 54.0 x 81.9
Weight (lbs/kg)| 65 / 29.6| 82 / 37.3| 111/50.5

EYEBOLT INSTALLATION

DESCRIPTION

Many of the popular models in the Yorkville speaker cabinet line are now equipped with flying hardware for overhead suspension applications. Depending on the model, two or more internal braces have been provided for rigging purposes. Each brace contains two bolt holes and provides center-of-gravity fly-points for use with in-line or angular loads. Many of the models will support additional suspended cabinets according to their specified working load limits.

IMPORTANT!!
THE RIGGING OF LOUDSPEAKER SYSTEMS IS AN EXTREMELY SERIOUS MATTER. OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING (BUT NOT LIMITED TO) CALCULATING WORKING LOAD LIMITS, HARDWARE INSTALLATION, AND
PERIODIC SAFETY INSPECTION OF ALL HARDWARE AND CABINETRY. IF YOU LACK THESE QUALIFICATIONS, DO NOT ATTEMPT THE INSTALLATION YOURSELF, BUT INSTEAD USE A PROFESSIONAL STRUCTURAL RIGGER. IMPROPER INSTALLATION CAN
RESULT IN BODILY INJURY OR DEATH. CONSULT A STRUCTURAL ENGINEER TO CALCULATE ADDED LOADS FOR A BUILDING. STRUCTURAL REINFORCEMENT MAY BE NECESSARY TO INSURE A SAFE INSTALLATION.

REQUIRED TOOLS

• 4.5mm (7/32”) Hex Wrench
• Thread lock adhesive (Removable Type)

EYEBOLT INSTALLATION

• Using a 4.5mm (7/32”) hex wrench, remove the flat head bolts from the top or bottom of the speaker enclosure to expose the tapped holes (on TX models, the flat head bolts are located within the track rails), as shown below. Be sure to keep these handy as they will be needed to seal the cabinet after the eyebolts are removed.
  IMPORTANT!!
  USE ONLY LOAD RATED FORGED EYEBOLTS. THESE MAY BE PURCHASED THROUGH YORKVILLE SOUND OR ATM FLY-WARE™. TO INSURE CABINET-BRACING STRENGTH, MAKE SURE ALL FLY- POINTS ARE SECURED WITH EITHER AN EYEBOLT OR FLAT HEAD HEX BOLT.

• Place a drop of thread-lock adhesive on the threads of the eyebolt and insert one into exposed hole. Tighten each eyebolt by hand until its fits snugly against the cabinet. Further tighten each eyebolt by rotating it another half turn. Be sure to insert eyebolts in the threaded hole directly in-line with the suspension cable. Always follow the eyebolt manufacturers installation and use instructions.

• Suspend each cabinet according to working load calculations and practices recommended by the rigging hardware manufacturer.

WORKING LOAD LIMITS

Specified working load limits have been determined for the enclosure as follows:

IMPORTANT!! READ ALL ENCLOSED INSTRUCTIONS ABOUT PROPER USE OF HARDWARE. TO INSURE PROPER INSTALLATION, FOR TECHNICAL INFORMATION ON SUSPENSION TECHNIQUES AND EXTERIOR ACCESSORY INFORMATION WE SUGGEST CALLING ATM FLY-WARES TECHNICAL SERVICES IN THE UNITED STATES AT (310)639-8282 MONDAY THROUGH FRIDAY FROM 9 AM TO 6 PM (PST) OR FAX AT (310)639-8284. YORKVILLE SOUND MAKES NO CLAIMS AS TO THE SAFETY OF THE ENCLOSURES IF RECOMMENDED LOAD LIMITS AND HARDWARE ARE NOT STRICTLY ADHERED TO. NOR DOES IT MAKE ANY SAFETY CLAIMS TO THE RESULTANT INSTALLATION.
IMPORTANT!! TRACK RAILINGS: UNITS THAT INCORPORATE THE TRACK RAILING SYSTEM HAVE THE SAME WORKING LOAD LIMITS AS THEY DO WHEN THEY ARE USED WITH EYEBOLTS. THESE RATINGS MAY BE LIMITED AND BASED ON THE RATINGS OF THE TRACK FITTINGS THEMSELVES. PLEASE ENSURE THAT THE RATING OF THE CERTIFIED TRACK FITTINGS EXCEEDS NECESSARY WORKING LOAD LIMITS.

Block Diagram for PS12s, PS15s & PS18s

DESIGNED & MANUFA CTURED BY YORKVILLE SOUND

Two & Ten Year Warranty

Unlimited Warranty
Yorkville’s two and ten-year unlimited warranty on this product is transferable and does not require registration with Yorkville Sound or your dealer. If this product should fail for any reason within two years of the original purchase date (ten years for the wooden enclosure), simply return it to your Yorkville dealer with original proof of purchase and it will be repaired free of charge. This includes all Yorkville products, except for the YSM Series studio monitors, Coliseum Mini Series and TX Series Loudspeakers.

Freight charges, consequential damages, weather damage, damage as a result of improper installation, damages due to exposure to extreme humidity, accident or natural disaster are excluded under the terms of this warranty. Warranty does not cover consumables such as vacuum tubes or par bulbs. See your Yorkville dealer for more details. Warranty valid only in Canada and the United States.

Canada
Voice: 905-837-8481
Fax: 905-837-8746
Voice: 716-297-2920
Fax: 716-297-3689

www.yorkville.com

Yorkville Sound
550 Granite Court
Pickering, Ontario
L1W-3Y8 CANADA

Yorkville Sound Inc.
4625 Witmer Industrial Estate
Niagara Falls, New York
14305 USA
U.S.A.
Voice: 716-297-2920
Fax: (716) 297-368

WORLD HEADQUARTERS

CANADA
Yorkville Sound Limited
550 Granite Court
Pickering, Ontario
L1W 3Y8 CANADA
Voice: 905-837-8481
Fax: 905-837-8746

U.S.A.
Yorkville Sound Inc.
4625 Witmer Industrial Estate Niagara Falls, New York 14305, USA
Voice: 716-297-2920
Fax: 716-297-3689

Manual-Owners-PS12S-PS15S-PS18S-00-2v8 • August 26, 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>