YESKAMO TJ15-10804-2T Wireless Security Camera System User Guide

YESKAMO TJ15-10804-2T Wireless Security Camera System

Statement

1. Thanks for purchasing this product. YESKAMO is committed to providing our customers with reliable security solution and protect your property all times.
2. This is the fast setup guide which only helps you familiar with this product quicker, for more information about product, please refer to the full user manual
3. Though we apply all efforts to make the manual complete and accurate, there could still be some discrepancies due to products’ timely update. Detailed information is in accordance with the final products.

Safety Caution

1. Wireless only means no any cables between camera and monitor base, but the whole camera system need to be plugged into power socket for power supply
2. Please use the included power supply with the product to prevent damage to the product
3. Please avoid any avoidable obstacles and electromagnetic product between camera and monitor for better signal
4. All man-made damages are outside the scope of free warranty

Technical Support

• Website: www.yeskamo.com

• Email: usservice@yeskamo.com (for US)
  ukservice@yeskamo.com (for UK) US

• Cell: +1 830 745 5888 UK

• Cell: +44 20 38074763

Product Introduction

Wifi Floodlight Security Camera

1. Microphone: Pick up audio
2. 4pcs Floodlight: will turn on automatically in the darkness when PIR sensor was triggered
3. 4pcs IR led: IR lads will automatically switch on at darkness for night vision
4. Speaker: transmit sound
5. 3dBi Antenna: receives wifi signal from monitor
6. Weatherproof IP66 Housing: working temperature: -20 °C /-4 1l to 60 °C/1401l
7. IR Cut Filter: auto switch day/night
8. PIR Sensor: detect objects in the monitoring area
9. TF Card Slot: Insert TF Card for video storage. (Max support 128G TF Card, TF card must be FAT32 format. Camera in kit doesn’t support TF card function)
10. Reset button: Press and hold reset button about 5-10 seconds to restore camera to factory setting.
11. 2-Axis Mounting Bracket: adjust installation angle and vandal-proof inside cable 360° all-round swiveling and 90° up-down adjusting
12. Power-in Port: connect with provided 12V lA plug for power supply
13. RJ45 Ethernet port :
14. A: pair/ match code camera with monitor when camera lose connection
15. B: hard wire camera with monitor or router to get stable signal (DO NOT CUT IT OFF)

2 in 1 NVR Recorder with Monitor (Abbreviated as Monitor)

1. Screen Button: press to turn on/ off the screen (Please keep the screen off when you out, make it more durable)
2. Antenna: release strong wireless signal from Monitor
3. 3.5 Internal Hard Disk: save video from NVR system
4. Power Input: connect the provided 12V 3A adapter for power supply
5. USB port: for USB mouse control, USB flash drive port for video footage backup and system upgrading
6. WAN Port:
7. connect to router with Ethernet cable for remote viewing
8. When you add new camera to YESKAMO Monitor, or your camera lose Connect on with monitor, you need this Ethernet port to pair camera with Monitor
9. HDMI video output: connect monitor to HDMI input port of your TV/monitor (HDMI cable not included)
10. Audio-out: insert with the Speaker

Connection Instruction

1. Plug camera to power socket with provided 12V 1A adapter
2. Plug monitor to power socket with provided 12V 3A adapter
3. Plug mouse to Monitor
4. 0ptional: If you want extra TV/monitor ,connect monitor to it with HDMI cable(Not included)
5. Use Ethernet cable to connect the WAN port of Monitor to LAN port of router, make the system online if you want to remotely view the cameras on phone app (Skip it if you only want to view local videos on monitor)

User name: admin
Password: No password (Default password is no password, let it blank and click “Ok” to login the camera system)

Note:

1. The laptop can’t be used as monitor directly, please use your TV or desktop’s monitor for local viewing
2. The monitor has a built in router and the cameras receive the wireless signal from the monitor. So it is suggested to place the monitor at the center of monitoring area and avoid any avoidable obstacle between the cameras and the monitor and keep the antenna of camera parallel with monitor’s antenna

Remotely view the cameras on the phone

1. Make sure the NVR monitor is ONLINE status: Connect the WAN port of NVR monitor to LAN port of router with Ethernet cable, then the NVR monitor will be ONLINE. Right click the mouse to enter main menu > Fast Network > Cloud (P2P) > ONLINE
2. Download free app Search free APP “YESKAMO” be updated sometimes, if your phone app menu is different from the menu in user manual, please contact us to get the latest user manual “Esee Cloud” in App store or Google play. The phone app will
3. Create an account and log in phone app Register an account with your email address /phone number and password. A verification code wil be send via text,
4. Add Cloud ID:
5. Enter APP>Enter APP > click “” in the right top corner or center of the phone > Scan the Could ID
6. Enter APP> click “+” in the right top corner or center of the phone> “Other ways to add”> Input “Device Cloud ID”> the default password is no password, click “Add” and Complete” to finish

  * Cloud ID:
    1. Right click the mouse to enter main menu> Fast network> Cloud (P2P)
    2. Right bottom corner of the monitor
    3. The label on the NVR/Monitor
  * Name of device: customize the system name (such as home, office, room..)
  * User Name: default is admin (the same as your NVR monitor)
  * Password: default is no password, leave it blank/empty (same as your NVR monitor system)![YESKAMO-TJ15-10804-2T-Wireless-Security-Camera-System-07](https://manuals.plus/wp-content/uploads/2023/01/YESKAMO-TJ15-10804-2T-Wireless-Security-Camera-System-07.png)

5. Remotely view camera via phone: Double tap the screen, and you can view camera anywhere anytime.
6. Two way audio communication
   Turn on the “speaker” button at top right corner of phone app and you can hear the audio from camera side.
   Tap “microphone” button to enter chat screen, then press and hold “microphone” button and you can talkback to camera side.
   Tap “hang up” button to return preview screen
   Note: Only one user can use the “microphone” at one time, others can use the microphone when the first person hangs up.

How to enable the Siren Alarm from camera side?

There are 4 types of PIR activated alert available, Buzzer, Email, phone app notification and IPC Alarm.
You can customize the PIR activated alerts based on your requirement.

• Buzzer: Monitor will beep when motion is detected
• Email alert: you will receive an email alert(refer to “full manual user”)
• Phone app notification: you will get a phone app notification push
• IPC Alarm: you will hear siren alarm from camera side

Take IPC alarm as an example, it sounds an siren alarm from camera side when PIR is activated. Right click mouse to enter main menu> system setup> channel setup> video detection> select channel and click “Enable” > check/enable “IPC Alarm”> Click “Apply” to save the setting.

Note:

1. If you choose phone app or email alert for this camera, please make sure your camera system is online.
2. If you want to setup the same alerts for all channels, please repeat above steps or click “Copy to all

How to manually turn off the floodlight at night?

This floodlight camera has a built in PIR sensor and floodlights. The floodlight will automatically switch on at night when detect any suspicious activities and offer true color videos. But you can customize the IR-Cut mode to turn off the floodlight as below steps: Before customizing the IR-Cut mode for a selected channel, please double click the channel you want set, to enter full screen mode. Right click mouse to enter main menu> Color Adjust> IR-Cut mode: Infrared, Daylight, Night, Full Color, Smart Mode

Note:

1. The light of floodlight camera lasts for about 20 seconds.
2. The time interval for floodlight is about 2 minutes.
3. Only under the “Full color” mode and “Smart” mode, the floodlight will turn on at night.

How to add a new camera to YESKAMO NVR with monitor?

The cameras are paired with monitor before packed and it will auto pair with monitor after you plug whole camera system to power socket, but if the camera lost connection with monitor accidentally or you want to add a new camera to this kit, please pair/ match code the camera with monitor as below steps:

1. Take the camera near monitor

2. Plug camera to power outlet via the provided 12V 1A power adapter

3. Use Ethernet cable (RJ45) to connect camera with monitor, the WAN indicator light at back panel of Monitor will turn on
   

4. Right click mouse to enter main menu > Video Manage The upper box shows information of camera, and lower box shows channel information of monitor

5. If the channel status at lower box shows “IPC disconnect”, “connect fail”, ” different segment”. select that channel with mouse, then click “delete” and the status of that channel will be “No video source”

6. Click “Search” in the upper box, new lP address will pop up in minute and then click “match code”

7. The camera will be connecting with monitor and “Wifi add” interface will pop up

8. Click ” Exit” until the camera’s IP address pops up for that channel. (The IP address will be 172.20.14.xx)

9. The picture of camera will be shown on monitor and the status of that channel will be “connect success” on video manage interface 10) Then you can disconnect the Ethernet cable and install the camera at anywhere you want (Camera should be install within the monitor’s wifi range, and Connect the Ethernet cable back to router with monitor if need remote view)

How to install hard drive for monitor?

The monitor need a hard drive to save the record, If you bought a monitor without hard drive or you want to replace the pre-install hard drive with larger memory. Please install it by yourself as the following instruction:

1. Remove the screws on the back panel of monitor.
2. Take the back panel off from monitor.
3. Holding the hard drive and the monitor panel, gently and line up four holes on the hard drive with the monitor panel.
4. Screw the provided screws into the holes between hard drive and back panel by a Philips screw driver.
5. Connect the SATA power and data cables from the monitor to the corresponding ports on your HDD.
6. Slide the monitor panel back on and fix the panel with Phillips Screws as picture.
7. This is a Quick User Guide, please refer to the full user manual for more detailed information

This is a Quick User Guide, please refer to the full user manual for more detailed information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>