YESKAMO W512-US3004-1T WiFi Security Camera System User Guide

W512-US3004-1T WiFi Security Camera System
User Guide

Product Introduction

Wifi Floodlight Security Camera

1. 2pcs Floodlight: will turn on automatically in the darkness when human detected

2. 2pcs IR led: IR leds will automatically switch on at darkness for night vision

3. SdBi Antenna: receives wifi signal from NVR recorder

4. Weatherproof IP66 Housing: working temperature: -20 C/-4 F to 60 C/140 F

5. IR Cut Filter: auto switch day/night

6. Microphone: Pick up audio

7. Speaker: transmit sound

8. 2-Axis Mounting Bracket: adjust installation angle and vandal-proof inside cable 360° all-round swiveling and 90° up-down adjusting

9. RJ45 Ethernet port:
   A: pair / match code camera with NVR when camera lose connection
   B: hard wire camera with NVR or router to get stable signal (DO NOT CUT IT OFF)

10. Power-in Port: connect with provided 12V 1A plug for power supply
    Note: It’s suggested to install the camera under the roof to avoid uncessary wearing and tearing.

Network Video Recorder monitor (Abbreviated as NVR monitor)

1. Screen button: turn on/off screem

2. 3.5 inches internal hard drive should be installed inside based on need

3. Antenna: release strong wireless signal from NVR recorder

4. Power Input: connect the provided 12V 2A/3A adapter for power supply

5. USB port: for USB mouse control, USB flash drive port for video footage backup and system upgrading

6. WAN Port:
   A: connect to router with Ethernet cable for remote viewing
   B: When you add new camera to YESKAMO NVR recorder, or your camera lose connection with NVR recorder, you need this Ethernet port to pair camera with NVR recorder

7. HDMI video output: use HDMI cable to connect your another large screen and syncs the video. (HDMI cable not included)

Connection Instruction (Model No.: \W512-US3004-1T)

1. Plug camera to power socket with provided 12V 1A adapter
2. Plug NVR to power socket with provided 12V 2A/3A adapter
3. Plug mouse to NVR
4. Connect NVR monitor video to additional screen and sycns video with HDMI cable(not included)
5. Use Ethernet cable to connect the WAN port of NVR to LAN port of router, make the system online if you want to remotely view the cameras on phone app (Skip it if you  only want to view local videos on monitor)
   user name: admin Password: No password (Default leave it blank)

Note

1. The NVR monitor has a built in router and the cameras receive the wireless signal from it.
   So it is suggested to place the NVR monitor at the center of monitoring area and avoid any avoidable obstacle between the cameras and the NVR and keep the antenna of  camera parallel with NVR’s antenna

2. Please test well the camera to ensure it works before installation.

How to install hard drive for monitor?

The monitor need a hard drive to save the record. If you bought a monitor without hard drive or you want to replace the pre-install hard drive with larger memory.
Please install it by yourself as the following instruction:

G Remove the screws on the back panel of monitor.| Take the back panel off from monitor.

Holding the hard drive and the monitor panel, gently and line up four  holes on the hard drive with the monitor panel.| Screw the provided screws into the holes between hard drive and back panel by a Philips screw driver.

Connect the SATA power and data cables from the monitor to the corresponding ports on your HDD| Slide the monitor panel back on and fix the panel with Phillips screws as picture.

Remotely view the cameras on the phone

1. Make sure the NVR monitor is ONLINE status:
   Connect the WAN port of NVR monitor to LAN port of router with Ethernet cable, then the NVR monitor will be ONLINE.
   Right click the mouse to enter main menu > Fast Network > Cloud (P2P) > ONLINE

2. Download free app
   Search free APP “YESKAMO” , “EseeCloud” in App store or Google play.The phone app will be updated sometimes, if your phone app menu is different from the menu in user manual, please contact us to get the latest user manual

3. Create an account and log in phone app
   Register an account with your email address /phone number and password. A verification code will be send via text.

4. Add Cloud ID:
   A: Enter App? Enter APP > click “+” in the right top corner or center of the phone > Scan the jou
   B: Enter APP > click “+” in the right top corner or center of the phone > “Other ways to add”> Input “Device Cloud ID”> the default password is no password, click  “Add” and “Complete’to finish—Cloud ID:
   A: Right click the mouse to enter main menu> Fast network> Cloud (P2P)
   B: Right bottom corner of the monitor
   C: The label on the NVR/Monitor
   —Name of device: customize the system name (such as home, office, room…)
   —User Name: default is admin (the same as your NVR monitor)
   —Password: default is no password, leave it blank/empty (same as your NVR monitor system)

5. Remotely view camera via phone:
   Double tap the screen, and you can view camera anywhere anytime.

6. Two way audio communication
   Turn on the “speaker” button at top right corner of phone app and you can hear the audio from camera side.
   Tap “microphone” button to enter chat screen, then press and hold “microphone” button and you can talkback to camera side.
   Tap “hang up” button to return preview screen

Note:
Only one user can use the “microphone” at one time, others can use the microphone when the first person hangs up.

How to enable the Siren Alarm from camera side?

There are 5 types alert for motion detection: Buzzer, E-Mail Notice, phone app notification, Full screen and IPC Alarm.
Buzzer: NVR monitor will beep ‘dididi” when motion is detected E-mail Notice: enable it and then you are able to setup and receive email alerts.
APP Alarm: enable it and system send App notifications when motion happens.
IPC Alarm: enable to allow camera make siren alarm sound.
Full Screen: The monitor auto show full screen when camera detected motion.
Take IPC alarm as an example, it sounds an siren alarm from camera side when motion detected.
Right click mouse to enter main menu> system setup> channel setup> video detection> select channel and click “Enable” > check/enable “IPC Alarm” > Click “Apply” to  save the setting.

Note:

1. If you choose phone app or email alert for this camera, please make sure your camera system is online.
2. If you want to setup the same alerts for all channels, please repeat above steps or click “Copy to all”.

How to manually turn off the floodlight at night?

The floodlight on camera will turns on when detected human motion at night thus offer true color videos.
Floodlight default not turn on during the daytime.But you can customize the IR-Cut mode to setup on/off schedule of light as below steps:
Before customizing the IR-Cut mode for a selected channel, please double click the selected channel to enter full screen mode.
Right click mouse to enter main menu> color adjustment> IR-Cut mode: Infrared, Daylight, Night, Full Color, Smart Mode=

floodlight will never turn on
Night| Black & White| Black & White, floodlight will never turn on
Full Color| Color picture| Color picture, floodlight always turns on at night
Smart| Color picture| Black & white when No one passby, and floodlight switch on to offer color video once someone passby

Note:
A: The light of floodlight camera lasts for about 20 seconds.
B: The time interval for floodlight is about 2 minutes.
C: Only under the “Full color” mode and “Smart” mode, the floodlight will turn on at night.

How to add a new camera to YESKAMO NVR system?

The cameras are paired with NVR Monitor before packed and it will auto pair with NVR after you plug whole camera system to power socket, but if the camera lost  connection with NVR recorder accidentally or you want to add a new camera to this kit, please pair/ match code the camera with NVR as below steps:

1. Take the camera near NVR recorder
2. Plug camera to power outlet via the provided 12V 1A power adapter
3. Use Ethernet cable (RJ45) to connect camera with NVR recorder, the WAN indicator light at back panel of NVR will turn on
4. Right click mouse to enter main menu > video manage The upper box shows information of camera, and lower box shows channel information of NVR
5. If the channel status at lower box shows “IPC disconnect”, “connect fail”, “ different segment” …, select that channel with mouse, then click “delete” and the status of  that channel will be “No video source”
6. Click “Search” in the upper box, new IP address will pop up in minute and then click “match code”
7. The camera will be connecting with NVR and “Wifi add” interface will pop up
8. Click “ Exit” until the camera’s IP address pops up for that channel. (The IP address will be 172.20.14.xx)
9. The picture of camera will be shown on monitor and the status of that channel will be “connect success” on video manage interface
10. Then you can disconnect the Ethernet cable and install the camera at anywhere you want (Camera should be install within the NVR’s wifi range, and Connect the  Ethernet cable back to router with NVR if need remote view )

This is a Quick User Guide, please refer to the full user manual for further more information.

Statement

1. Thanks for purchasing this product. YESKAMO is committed to providing our customers with reliable security solution and protect your property all times.
2. This is the fast setup guide which only helps you familiar with this product quicker, for more information about product, please refer to the full user manual
3. Though we apply all efforts to make the manual complete and accurate, there could still be some discrepancies due to products’ timely update.Detailed information is in accordance with the final products.

Safety Caution

1. Wireless only means no any cables between camera and NVR base, but the whole camera system need to be plugged into power socket for power supply
2. Please use the included power supply with the product to prevent damage to the product
3. Please avoid any avoidable obstacles and electromagnetic product between camera and NVR for better signal
4. All man-made damages are outside the scope of free warranty

Technical Support
Website: www.yeskamo.com
Email: usservice@yeskamo.com (for US)
ukservice@yeskamo.com (for UK)
US Cell: +1 830 745 5888
UK Cell: +44 20 3807 4763

Documents / Resources

| YESKAMO W512-US3004-1T WiFi Security Camera System [pdf] User Guide
W512-US3004-1T WiFi Security Camera System, W512-US3004-1T, WiFi Security Camera System, Security Camera System, Camera System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>