AcuityBrands CPXC 2X2 TUWH 120 Smart CPX LED Instruction Manual

: June 9, 2024
: AcuityBrands

Table of Contents

AcuityBrands CPXC 2X2 TUWH 120 Smart CPX LED
INSTALLATION INSTRUCTIONS
LED IMPORTANT SAFETY INSTRUCTIONs
FCC Supplier’s Declaration of Conformity
Motion Sensor Precaution
T-BAR CEILING GRID INSTALLATION INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AcuityBrands CPXC 2X2 TUWH 120 Smart CPX LED

Acuity-Brands-CPX-2X2-TUWH-120-Smart-CPX-LED-PRODUCT

INSTALLATION INSTRUCTIONS

inteligenteSmart CPX LED Flat Luminaire with motion sensor

3-YEAR LIMITED PRODUCT WARRANTY
Visit www.acuitybrands.com to view the terms and conditions of your Acuity Brands Lighting, Inc. limited warranty.

Model Number

CPXC 2X2 TUWH 120
CPXC 2X4 TUWH 120

SAVE THESE INSTRUCTIONS

Protect yourself. Before installing, read these instructions carefully and save them for future reference.

Date Installed:

TOOLS REQUIRED FOR INSTALLATION

Safety glasses
Protective Gloves
Phillips screwdriver
Pencil
Hammer
Pliers
Ruler
Wire Strippers
Flat blade screwdriver
Smartphone

LED IMPORTANT SAFETY INSTRUCTIONs

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
Installation and service of luminaires should be performed by a qualified licensed electrician.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards involved. Regular fixture maintenance programs are recommended.
It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.
DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov
These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

Disconnect or turn off power before installation or servicing.
Verify that supply voltage is correct by comparing it with the luminaire label information.
Make all electrical and grounded connections in accordance with the National
Electrical Code (NEC) and any applicable local code requirements.
All wiring connections should be capped with UL approved recognized wire connectors.

CAUTION
RISK OF INJURY

Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

WARNING
RISK OF BURN

Allow lamp/fixture to cool before handling.
Do not touch enclosure or light source.
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling

CAUTION
RISK OF FIRE

Keep combustible and other materials that can burn, away from lamp/lens.
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

CAUTION: RISK OF PRODUCT DAMAGE

Never connect components under load.
Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation.
Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-wired to the luminaire must be checked for compatibility with the luminaire prior to installation. LED fixtures must be powered directly off a switched circuit.
Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient temperature.
Only use fixture in its intended location.
LED products are Polarity Sensitive. Ensure proper Polarity before installation.
Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or servicing of the unit.
Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
Some components inside the fixture may not be serviceable. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative for assistance.
Always read the fixtures complete installation instructions prior to installation for any additional fixture specific warnings.
Always ensure that the electrical distribution system is up to NEC (and any applicable local code) requirements.
Verify that power distribution system has proper grounding. Lack of proper earth ground can lead to fixture failure and may void warranty.

Choose either Part 15 OR Part 18 and move to Page 3 Installation Instructions under Delivery. Lithonia Outdoor will always use Part 15. All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation

This device complies with Part 18 of the FCC Rules but may cause interference with cordless and cell phones, radios, televisions, and other electronic devices. To correct the problem, move the device away from the luminaire or plug into a different outlet. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communications equipment operating between 0.45-30MHz.

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and Conditions, please visit www.acuitybrands.com.

Indoor/Outdoor

Lithonia Lighting
Carandini
Holophane
RELOC
Light Concepts

Indoor Lighting

Aculux
Gotham
Indy
Juno
Mark Architectural Lighting
Peerless
Renaissance Lighting
Winona Lighting

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

FCC Supplier’s Declaration of Conformity

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, (2) this device must accept any
interference received, including interference that may cause undesired operation, (3) any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Suppliers Name: Acuity Brands Lighting, Inc.
Suppliers Address (USA): One Lithonia Way | Conyers, GA 30010
Suppliers phone number: 800.323.5068
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.

Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. This device complies with Innovation, Science, and Economic Development Canada license-excempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference; and
This device must accept any interference, including interference that may cause undesired operation of the devic

This equipment complies with ISED radiation exposure limits set fourth for an uncontrolled environment. This equipment should be installed and operated with minimum 20cm between the radiator & your body.

Only for 5G Devices
The devices for the band 5150-5350 MHz are only for indoor use, to avoid interference from WIFI signal.

Motion Sensor Precaution

This luminaire is equipped with a radio based motion sensor. To prevent false triggering of fixture:

The installation distance between fixtures should be least 2ft from each other.
Keep Wi-Fi router at least 3.5ft from fixture.
Avoid installing fixture near metal, glass, or concrete walls (least 2ft).
Keep moving objects such as fans at least 3.5ft from fixture.

T-BAR CEILING GRID INSTALLATION INSTRUCTIONS

Note: Turn off power at circuit breaker box!

Install fixture in T-bar ceiling opening.
From above the ceiling, secure the luminaire to T-bar grid by bending the built-in T-bar clips in all 4 corners of luminaire.
Following local codes, attach the luminaire to the building structure using proper hanger wire to support the luminaire in at least two opposite corners. Use the holes provided in the T-bar clips.
From above the ceiling, take out the screw and remove the junction box cover and locate the driver supply wires (1 black, 1 white, 1 green/ground).
Remove one knockout in the access plate and attach the building supply conduit.
With the power turned off, make electrical connections according to local codes. Secure the junction box covers back into the luminaire with screw. Turn ON the power at circuit breaker and test successful installation.
Load the Samsung SmartThingsLoad SmartThings® App to your Android or iOS mobile device. Go to quick start guide for for pairing instructions.