STIHL Bluetooth Labor Protection Headset Instruction Manual
- June 9, 2024
- STIHL
Table of Contents
STIHL Bluetooth Labor Protection Headset
Thank you for choosing our company’s labor protection earphone products. Read the following instructions in detail to help you quickly understand and correctly use this product
Schematic diagram
Wearing a method
- Distinguish between the left and right earphones (Bluetooth pickup is on the left), and pull both earphones with appropriate force.
- The headband of the earphone is placed on the top of the head, and the two ears are respectively completely placed in the earphone cover; ,
- adjust the length of the headband until comfortable to wear!
Bluetooth function
method of application
- Turn on/off Long press “on/Off” button for 3 seconds, Bluetooth function will be turned on, and the indicator light will be blue (on for 1 second); Similarly, hold down the “On/Off” button for 3 seconds to turn off Bluetooth.
- Pairing status and clearing the pairing list Press the “On/Off” button for 6 seconds in the power off state, or press the “Play” button for 3 seconds in the connected state to disconnect the connection, that is, to enter the pairing state. At this time, the Bluetooth indicator flashes red and blue rapidly. When the headset is in the pairing state, it can be found and paired by other devices such as mobile phones. The device name of this product is “J&Y01”. The matched devices are saved in the list. In the pairing state, hold down “volume -” and “volume +” for 5 seconds at the same time to clear the paired list, and the indicator turns blue for 2 seconds.
- Disconnected status and Connected status When the earphone is disconnected (the indicator blinks red every 5 seconds), the earphone will actively connect the device if there is a device in the pairing list. When the headset is connected to the device or is working, the indicator will flash blue every 10 seconds.
- Call function and control When the headset is connected, double-click Play to redial the last dialed number. When the earphone is dialing out, click Play to cancel dialing out. When the headset is ringing, click Play to answer the call, and long press Play to reject the call. If the headset is in an ongoing conversation, click Play to cancel the current call. Double-click Play to switch between Call with Mobile phone and Call with Headset, and click Volume +/- to increase or decrease the volume. When the headset is talking with 1#, 2# comes in. Click “Play” to hold the call and answer the call. Long press “Play” to refuse to answer the call. When the headset is in a three-way conversation, hold down the “Play” key to switch the conversation between 1# and 2#, and click the “Play” key to cancel the current conversation.
- Music playback and control When the headset is connected, click Play to play the music. During the music playing, click Play to pause the music playing. When the headset is playing music, press Volume + to increase the volume, hold down Volume + to play the next song, click Volume – to reduce the volume, and hold down Volume -to play the previous song. Bluetooth undervoltage prompt function with automatic shutdown When the bluetooth function is enabled, when the battery is running low, the indicator will flash red every 10 seconds and emit a “beep” sound every 2 minutes. When the battery is running out or the pairing time exceeds 5 minutes, the Bluetooth will automatically shut down
LINE-IN
The LINE IN function
method of application :
Use the attached 3.5mm audio cable to connect the earphone with your player
device, and you can enter the line-in working state. (Automatic detection of
connection line insertion and start to work, should be unplugged after use to
avoid running out of power)
Note:
- Adjust the line-in volume knob to adjust the volume;
- When an audio cable is inserted into the line-in interface, the Bluetooth function cannot be turned on, and the enabled one will be automatically turned off.
- after use, the audio cable plug on the earphone must be pulled out, otherwise the battery may be exhausted!
FCC warning
Any Changes or modifications not expressly approved by the party responsible
for complain nice could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B dig ital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reaso nable protection against harmful
interference in a residential installation. This equipment g enervates uses
and can radiate radio frequency energy and, if not installed and used in acco
dance with the instructions, may cause harmful interference to radio
communications. Ho wever, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct t
he interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following tw o conditions:
- This device may not cause harmful interference, and
- this device must a ccept any interference received, including interference that may cause undesired operation. This device complies with FCC radiation exposure limits set forth for an uncontrolled enviro moment and it also complies with Part 15 of the FCC RF Rules. This equipment must not be c o- located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and consider removing the no-collocation statement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>