BATHOLOGY Spectrum 620 White Light Salt Panel Instruction Manual

: June 9, 2024
: BATHOLOGY

BATHOLOGY Spectrum 620 White Light Salt Panel Instruction Manual

Installation Considerations

Please read this manual in its entirely prior to installation
Carefully review all installation options and instructions before proceeding.
For safety purposes, use safety goggles at all times.
If there is any risk of uninsulated electrical connections in your wall / ceiling area, use insulating gloves.
Prior to installation, consider the placement carefully, taking into account the location of electrical, plumbing, and other fixture.
The Spectrum 620-W and 626-W require a minimum of 4” at both ends to insert or remove center salt block for mounting or removing panel.
Power Supplies and Receivers should be installed outside of the bathing environment. Do not install in Sauna Environment.
It is recommended that all electrical equipment be tested prior to installation.
Each Salt Panel Assembly may weigh up to 55 lbs and require additional framework or support. 3/4” Plywood is recommended to help support the weight of the fixture(s).

Installation – Overview

Note: It is recommended that all electrical equipment be tested prior to installation.
Note: Illustration below showcases Spectrum 620-W Humalayan Salt Panel Assembly which measures 48×12. Spectrum 626-W operates similarly, but measures 16×16. Surface mount shown.

Package Includes

Spectrum 621

Item| Quantity| Description
A| 1| Himalayan Salt Panel Assembly (Salt Pre-Installed)
B| 4| Himalayan Salt Blocks
C| 4| Mounting Screws (10×2-1/2)
Spectrum 627

Note: Control is required to operate this system. Depending on

installation – Himalayan Salt Panel (WIFI (Phase 1))

Determine the desired locations for the following: Power Supply (G), WIFI Receiver (F), and Salt Panel Assembly (A). Note: WIFI Receiver (F) and Power Supply
(G) must be in an accessible, dry location. Provided cord lengths are 50’ maximum. Note:
Himalayan Salt Panel Assembly
(A) can be recessed or surface mounted.
Install electrical boxes for the following: WIFI Receiver (F), Power Supply (G), and Salt
Panel Assembly (A).
Run a 120VAC externally switched GFCI outlet to power electrical box supplying power to Power Supply (G).
Mount WIFI Bracket to wall and place WIFI Receiver (F) into Bracket.
Route Light Extension Cable (E) from WIFI Receiver (F) to Salt Panel Assembly (A).
Connect the following to the WIFI Receiver (F): Main power cable from Power Supply (G) and Light Extension Cable (E). Note: Do not turn power on to WIFI Control yet, this will be done later. See page 12 for more details.

Installation – Himalayan Salt Panel (WIFI (Phase 3))

In the IOS / Android app store download the Smart Life Smart Living
Once installed, you can either create an account or tap “Try Now” to continue without creating an account. Note:
You will need to sign up for an account to be able to use smart home features such as Google or Alexa.
Power on WIFI Receiver (F), light should begin to flash on and off rapidly.
In the app, select the Blue + symbol in the upper right corner to pair control.
Select the “Add Manually” tab at the top, then select “Lighting” tab
Under lighting select “Light Source (Wi-Fi)”. When prompted, enter the WIFI network that you will be using to connect to.
Ensure light is flashing If not, follow on-screen steps to reset control. Confirm light is blinking ten press “Next”. Pairing process will not begin. Note: If pairing is unsuccessful the control may not be picking up the WIFI signal. Try repositioning the control.
Once pairing is successful, you are all set to program your light.

Operation – WIFI

Power Button: Turn on / turn off the
Salt Panel Assembly lights.

Installation – Himalayan Salt Panel (Remote (Phase 3))

Remote should already come paired with receiver. Follow steps below to repair existing remote or new remote.
Pairing option 1 – on receiver press the match key then immediately pretty the On / Off button on the remote. Pairing option 2 – turn power off then on to receiver then immediately press the On / Off button on the remote. Light should blink 3 times indiciating successful pairing.

Operation – Remote

Specifications – Salt Panel Assembly

Salt Block

Composition: Himalayan Salt Dimensions: 3-7/8” x 7-7/8”

Himalayan Salt Panel

Dimensions (620-W): 11-5/8”H x 47-1/4”W x 2-5/8”D
Dimensions (626-W): 15-1/2”H x 15-3/4”W x 2-5/8”D
Composition: Maple Plywood, Aluminum

Mounting Screws

Size: #10 x 2-1/2”

LED Light

Operating Voltage: 24VDC
Power Consumption: 26 Watts per Channel
Lumens: 2,745 per Panel

Specifications – WIFI Control

WIFI Receiver

Operating Voltage: 24VDC Power Consumption: 144 Watts Amperage: 1 Channel, 3 Amps Dimensions: 2.29”H x 1.21”W x .34”D

Power Supply

Operating Voltage: 120VAC Output Voltage: 24VDC Power Composition: 120W
Nominal Amperage: 5A / 120V Dimensions: 2.6” x 6.5” x 1.3” Connector: 24VDC, 50’