BATHOLOGY 511 Sauna Color Bathing Experience Installation Guide

: August 30, 2024
: BATHOLOGY

Table of Contents

BATHOLOGY 511 Sauna Color Bathing Experience
Product Specifications
Product Usage Instructions
Frequently Asked Questions (FAQ)
SAFETY & WARNINGS
PACKAGE CONTENTS
SPECIFICATIONS
CONNECTION OVERVIEW
INSTALLATION
OUTPUT BOX SETTINGS
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)
2 Phillips Head Screwdriver

BATHOLOGY 511 Sauna Color Bathing Experience

Product Specifications

DMX Driver:
- Operating Voltage: 24V DC
- Power Consumption: 4.2 – 12.6 watts per channel
- Output Voltage: 12-36V DC
- Output Current: 350mA Constant Current
- Lumens: 88
- Zones: 1 Zone RGB
- Trim Finish : Stainless Steel
- Trim Dimensions: 2 Diameter, 18 Profile
- IP Rating : IP20
- Certifications: UL, CE, FCC, CRUus
Led Light:
- Operating Voltage: 24V DC
- Power Consumption: 3 Watts
- Led Type : RGB
- Lens Composition: Tempered Glass
- Beam Angle: 1 Zone RGB
- IP Rating: IP20
- Certifications: UL, CE, FCC, CRUus
RGB Control:
- Output Signal: DMX 24VDC
- Operating Voltage: 24VDC
- Power Consumption: 500mA
- IP Rating : IP67
- Certifications: CE
Power Supply:
- Input Voltage : AC
- Output Voltage : DC
- Rated Power : 2 – 4 Watts
- AC Current: 1-3/16
- DC Current: 1-15/35
- IP Rating: IP67
- Certifications: CE

Product Usage Instructions

Safety & Warnings:
Before installation, read the manual thoroughly and adhere to safety guidelines.

Electrical Requirements:
Always turn off the power at the breaker box before starting any electrical work.

Package Contents:
The package includes various components like DMX Driver, RGB Control, Led Light, Power Supply, and necessary cables and tools for installation.

Installation:

Ensure all wiring is done by a certified electrician following national electric code.
Place electrical components in a moisture-free location protected from weather conditions.
Avoid exceeding maximum temperature ratings of components to prevent warranty void.
Avoid direct heat exposure to LED lights and carefully plan their placement to avoid eye contact.
Install the Spectrum 511 control exterior to the sauna room.
Test all system components before final installation.
Always disconnect power before making or disconnecting connections.

Required Tools for Installation:

2 Phillips Head Screwdriver
Power Drill
Flat Head Screwdriver
1-5/8 Hole Saw

Frequently Asked Questions (FAQ)

Can the Led lights be installed inside the sauna room?
No, the Spectrum 511 control is specifically designed for exterior installation only.
What is the maximum light cable distance from Driver to the farthest light?
The maximum distance is 100 feet.

SAFETY & WARNINGS

PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO INSTALLATION!

All wiring must be done in accordance with national electric code and local building codes by a cer-tified electrician.
All electrical components such as driver, power supply, and control must be installed in a location protected from moisture, rain, and or inclement weather.
Please note the maximum temperature ratings of all components on page 4 Specifications. Compo-nents should not be installed where maximum temperature of component will be exceeded, doing so will void warranty.
Do not install Led lights directly above or within 20” of heat source.
Consider light placement carefully. Each Led light should be placed to avoid direct contact with the bathers eyes.
Prior to installation, consider the placement of the Light Control carefully, taking into account the location of electrical, plumbing, and other fixtures.
The Spectrum 511 control is designed for installation exterior of the Sauna Room, control is not rat-ed for installation inside Sauna Room.
The maximum light cable distance from Driver to farthest light is 100’.
All system components should be tested prior to final installation.
Always fully disconnect power from the system prior to making or disconnecting any connections.

Electrical Requirements
Always turn off the power at the breaker box before starting any electrical work.

A 120V AC electrical outlet is needed to power the lighting system.
Your electrician will determine the type of electrical outlet, box, and pip-ing to be used.
Improper voltage or connections will damage the components and void warranty.

PACKAGE CONTENTS

Required Tools for Installation

SPECIFICATIONS

DMX Driver
- Operating Voltage: 24V DC
- Power Consumption: 4.2 – 12.6 watts per channel
- Output Voltage: 12-36V DC
- Output Current: 350mA Constant Current
- Connections: Power In – DC Female Barrel
- DMX
- In/Out – RJ45 Cat6
- Led Out – RJ45 Cat6
- Zones : 1 Zone RGB
- Operating Temp: -4°F – 122°F
- Dimensions: 7”L x 1.81”W x .82”H
- Light Capacity: 6 (per Driver)
- IP Rating : IP20
- Certifications: UL, CE. FCC, CRUus
RGB Control
- Output Signal : DMX
- Operating Voltage : 24VDC
- Power Consumption : 500mA
- Material: Aluminum Housing / Glass Face
- Connections:
- Power In – DC Female Barrel
- DMX In – RJ45 Cat6
- Mounting: Double Sided Adhesive/Silicone
- Dimensions: 4.72”L x 3”W x .59”H
- Operating Temp: 32°F – 122°F
- Zones: 1 Zone RGB
- IP Rating : IP67
- Certifications: CE
Power Supply
- Input Voltage : 120VA C
- Output Voltage : 24V DC
- Rated Power : 90W
- AC Current : 1.3A
- DC Current : 3.75A
- Operating Temp : -22°F – 158°F
- IP Rating : IP20
- Certifications: UL, CE, FCC
Led Light
- Operating Voltage: 24V DC
- Power Consumption: 3 Watts
- Led Type : RGB
- Lumens: 88
- Trim Finish : Stainless Steel
- Housing: Aluminum
- Beam Angle : 120° – Frosted Lens
- Lens Composition : Tempered Glass
- Connection: RJ45 Cat6
- Rough-In Cutout: 1-5/8”
- Trim Dimensions : 2” Diameter, 18” Profile
- Body Dimensions :
- 1-15/35” Diameter
- 1-7/8” Deep
- Operating Temp: 0°F – 230°F
- IP Rating: IP68
- Certifications: CE, ROHS
**Dimension

**

CONNECTION OVERVIEW

1 – 6 Lights Setup

7 – 12 Lights Setup
Requires purchase of second driver –

INSTALLATION

STEP 1 – DMX DRIVER

1. At determined location mount DMX driver.

Note: DMX driver must be installed in a dry accessible location or inside a waterproof electrical enclosure.

2. Take Output box and mount next to DMX driver. See Figure 1
3. Route 50’ dc power cable from DMX driver location to control location.

Note: Male end of dc cable connects to control.

4. Route 25’ CAT6 cable from DMX driver location to control location
5. At DMX driver take 25’ CAT6 cable ran to control and plug into DMX in lead on DMX driver.
6. Route 25’ CAT6 cable from Output box to light location. Repeat this step for each additional light.

Note: Refer to pages 9-12 for Output Box connections.

7. Take 4 port DC splitter and connect one male end to power in on DMX driver. Connect second male end to 50’ dc power cable for control.
8. Take 1’ Cat6 cable and connect one end to light out lead on DMX driver and other end to in port A of Output box.

Note: Each lead/driver handles 6 lights max. For more than 6 lights a separate driver kit must be purchased.

9. After checking and verifying all connections at driver and output box proceed to Led light installation.

STEP 2 – BRILLIANCE LED LIGHTS

1. Locate mounting plate and install at each light loca-tion by fastening plate to ceiling joist or wall stud. See figure 3
2. After finished material is installed use the 1-5/8” hole saw and power drill, drill a hole for each light.
3. After drilling hole ensure any installation is pushed to the side to maintain at least 2” clearance from top and sides of light.
4. Take female RJ45 connector from light and plug into RJ45 cable from DMX driver.
5. Run a 1/8” bead of silicone around edge of light for wet applications. See figure 3
6. Take light and push up into opening until trim is flush with surface.
7. Back at DMX driver plug Cat 6 cables from each light into 12 port splitter box.

Note: Repeat above steps for each additional light.
Note: Refer to pages 9-12 for output box connec-tions and setup.

STEP 3 – CONTROL

1. At determined control location cut a 1-1/2” x 2-13/32 square hole to mount control.
2. Take the 25’ CAT6 cable run from DMX driver and plug into RJ45 pigtail on control.
3. Take 50’ DC Power Cable and plug into DC pigtail on control.
4. Remove backing off double sided adhesive.
5. Run a continuous bead of silicone on back side of control.
6. Press control onto wall ensuring level and secure. Wipe away any access silicone.

STEP 4 – STARTUP & TESTING

1. After completing all installation steps take 4 port DC splitter and plug Female end into Male end from power supply.
2. Plug power supply into 120VAC outlet.
3. Verify DMX driver lights up and screen displays 001

Note: If driver is not displaying 001 or any other number upon applying power proceed to troubleshooting steps on page #13.

4. At control press power button to turn on lights. Verify all lights in room come on and cycle through colors.

OUTPUT BOX SETTINGS

Note: Input A will handle up to 6 lights.

Note: Input B will handle up to 6 lights.

TROUBLESHOOTING

No Power
- Verify electrical outlet has proper voltage.
- Check that connections on DC splitter secure and connected.
Power but lights not turning on
- Check DMX CAT6 cable from driver to control is secure and connected.
- Check DC power cable from driver to control is secure and connected.
- Check 1’ CAT6 cable to output box is secure and connected on both ends.
- Check all 25’ CAT6 cables to lights are secure and connected.
- Verify correct setup on output box for the amount of lights. See pages 9-12
- Verify each light functions by testing directly to driver independently.
  Note: If one light goes bad with multiple lights all lights will shut off as lights are in series.
Lights on no function from Control
- Check DMX CAT6 connections at control and driver are secure and connected.
- Check DC power cable from driver to control is secure and connected.

DMX Driver Menu Settings
To access menus to verify or troubleshoot follow steps bellow, see figure 5 for reference.

Channel Menu

1. Press and hold buttons #2 and #3 at the same time for 3-5 seconds, screen will flash.
2. Press button #1 until 1ch displays.
3. Press and hold any button for 3-5 seconds to exit and save setting.

Mode Menu

1. Press and hold buttons #1 and #2 at the same time for 3-5 seconds, screen will flash.
2. Press button #3 until ru2 displays.
3. Press and hold any button for 3-5 seconds to exit and save setting.

DMX Address Menu

1. Press and hold button #1 for 3-5 seconds, screen will flash.
2. Press button #1, #2, and #3 until 001 displays.
3. Press and hold any button for 3-5 seconds to exit and save setting.

PWM Frequency Menu

1. Press and hold button #1 and #3 for 3-5 seconds, screen will flash and display P – c.
2. Press button #1, until 2 displays. Press button #3 until 2 displays. Screen should display 2 – 2
3. Press and hold any button for 3-5 seconds to exit and save setting.

REPLACEMENT PARTS