BATHOLOGY Spectrum 511 Steam Sauna Bath Instruction Manual

Spectrum 511
Color Bathing Experience Installation and Operation Manual

Installation Considerations

Please read this manual in its entirely prior to installation
CAUTION
Carefully review all installation options and instructions before proceeding.
CAUTION
For safety purposes, use safety goggles at all times.
WARNING
Before wiring to power supply, turn off electricity at the fuse or circuit breaker box.
WARNING
Check for piping /electrical before cutting or drilling.
WARNING
Some electrical components are not waterproof.
WARNING
If there is any risk of uninsulated electrical connections in your wall / ceiling area, use insulating gloves.
!IMPORTANT
All wiring must be done in accordance with National Electric Code and local building code.
!IMPORTANT
Prior to installation, consider the placement carefully, taking into account the location of electrical, plumbing, and other fixtures.
!IMPORTANT
Touch Interface can be installed outside of a wet environment, on a vertical wall, convenient for user operation. It can be installed a dry bathing environment 36” above the floor maximum. Do not install inside wet environment

Installation – Overview

Desired Light Locations

NOTE: Do not hot swap any electrical components. Fully disconnect system from power source before swapping electrical components.
NOTE: It is recommended that all electrical equipment be tested prior to installation.

Package Includes

Installation – DMX Driver / Power Supply

Installation for 1-24 Lights

1. Determine best location for DMX Driver (A) and DMX Power Supply (K), making note of cord lengths.
2. Using a screwdriver fully loosen the 48VDC Output + and – on power supply (K) and 48VDC Input + and – on the DMX driver (A).
3. Connect the Red wire to the + Output on the power supply (K) and the other end to the + Input on the DMX driver (A).
4. Connect the Black wire to the – Output on the power supply (K) and the other end to the – Input on the DMX driver (A).

Dip Switches
Brilliance lights run on 350mA. Ensure that Dip switch 1 and 2 are both in the down position at 350mA.

Additional Power Supply for 25 – 48 Lights

1. Follow and complete installation for 1-24 lights.
2. Mount power supply (K) next to first power supply (K).
3. Using a screwdriver fully loosen the 48VDC Output + and – on power supply (K) and 48VDC Input + and – on the DMX driver (A).
4. Connect the Red wire to the + Output on the power supply (K) and the other end to the + Input on the DMX driver (A).
5. Connect the Black wire to the – Output (K) on the power supply and the other end to the – Input on the DMX driver (A).

Installation – Touch Interface

1. Determine the desierd location for the Touch Interface (B), making note of the cord lenghts.
2. Cut a 1-1/2”W x 2-13/32” H hole in desired location for the Touch Interface (B).
3. Install a standard single gang electrical box in an accessible dry location.
4. Run a grounded 120VAC from the power supply to the accessible dry location’s electrical box.
5. Run the DMX IN Cable (E) wires and the Power Supply Connector (D) wires to the Touch Interface’s (B) hole cutout.
6. Remove orange 4 screw terminal block and 7 screw terminal block from respective pin terminals.
7. Using a screwdriver, fully loosen the “GND”, “D-”, and “D+” sections of the orange 4 screw terminal, and “GND”, and “V in +” of the 7 screw terminal.
8. Connect the DMX IN Cable (E) GND to the “GND” orange 4 screw terminal block.
9. Connect the DMX IN Cable (E) Red D- to the “D-” orange 4 screw terminal block.
10. Connect the DMX IN Cable (E) Black + to the “D+” orange 4 screw terminal block.
11. Connect the Power Supply Connector (D) White – to the “GND” 7 screw terminal block.
12. Connect the Power Supply Connector (D) Black + to the “V in +” 7 screw terminal block.
13. Using a screw driver, tighten the “GND”, “DMX -”, “DMX +”, sections of the 4 screw terminal, and “GND”, and “V in +” of the 7 screw terminal.
14. Insert orange 4 screw terminal block and 7 screw terminal block into their respective pin terminals.
15. Remove DMX Driver’s (A) DMX IN screw terminal block from pin terminal.
16. Connect the DMX IN Cable (E) Ground to the DMX Driver’s (A) DMX IN screw terminal block’s “GND”.
17. Connect the DMX IN Cable (E) Red to the DMX Driver’s (A) DMX IN screw terminal block’s “D-”.
18. Connect the DMX IN Cable (E) Black to the DMX Driver’s (A) DMX IN screw terminal block’s “D+”.
19. Using a screwdriver, tighten the “GND”, “D-”, and “D+” sections of the DMX IN screw terminal block.
20. Insert DMX IN screw terminal block into its pin terminal.
21. Test light system prior to mounting Touch Interface (B) to wall. Verify connections are secure and working properly.
22. Secure Touch Interface (B) to electrical box (see figure 3).

Installation – Brilliance Light Fixtures

Warning: The Output Box(G) should be kept in an accessible location when installed. Only use the Output Box (G) when assembling the Brilliance Light Fixtures (I) and components of this kit.
Important: Driver has 4 ports. Each port operates 12 lights max. Take this into consideration when planning light installation.
Note: If only running 1 light Output Box does not need to be used. Light cable will plug directly into DMX driver port. This will apply for the 7th light as well.

1. Determine number of lights per input. Limit 6 lights per input.
2. Construct light assembly using the diagrams on the next page.
3. Determine desired Brilliance Light Fixture (I) location.
4. FOR REMODELS: Skip to 6. FOR NEW ROOMS: Mount 16” Location Template (J) to ceiling joist to indicate desired Brilliance Light Fixture (I) location. Use notches to quickly align desired location to other fixtures in the room.
5. Make a 1-5/8” hole in desired location.
6. Install light assemblies.
7. Mount Brillinace Light Fixture (I) to ceiling through 1-5/8” cutout.
8. Repeat steps 4 – 8 for each light.

Operation

On / Off
Power Off – Press and hold for 2 seconds. Turns on Touch Interface. Restores most recent settings.
Power On – Press and hold for 2 seconds. Turns off touch Interface.
ColorColor
“C” Button – Press and Hold for 2 seconds. Enables color mode.
“1” Button – Red.
“2” Button – Green.
“3” Button – Blue.
“4” Button – White.
Touch Toggle – Press and drag in a clockwise or counter-clockwise motion to cycle through all colors.
Brightness
“B” Button – Press and hold for 2 seconds. Enables brightness mode.
“1”, “2”, “3”, Uses color mode or pre-programmed scene mode “1”, “2”, “3”, “4” Button – “4” functionality, based on which mode was used prior to brightness mode.
Touch Toggle – Press and drag in a clockwise motion to increase brightness. Counterclockwise decreases brightness.

Pre-Programmed Scene
“P” Button – Press and hold for 2 seconds. Enables Pre-Programmed Scene mode.
“1” Button – Red – Magenta – White – Turquoise – Green – Yellow – White – Magenta – Blue – Turquoise – White – Yellow.
“2” Button – Red – Yellow – Green – Turquoise – Blue – Magenta
“3” Button – Yellow – Turquoise – Magenta
“4” Button – Red – Magenta – White – Turquoise – Green – Yellow – White – Magenta – Blue – Turquoise – White – Yellow (Faster version of “1”)
Touch Toggle – Press and drag in a clockwise or counter-clockwise motion to cycle through 10 pre-programmed scenes.

Product Care

For routine cleaning, simply use a soft damp cloth and common household soap. Use a damp cloth to wipe clean, then dry. Clean product frequently to avoid calcium deposits on surfaces. Use only mild soap. Never use abrasive cleaners, bleach, disinfectants or cleaning products containing alcohol, ammonia, hydrochloric or phosphoric acids as they may damage the product’s finish. To clean electrical components, gently wipe down using a dry cloth or duster. Never use a wet duster, water, or any other liquid to clean the device.

Replacement Parts

Contact your Bathology representative for Spectrum 511 Color Bathing Experience replacement parts.
800-957-2862
www.Bathology.com

Specifications

DMX Driver
Operating Voltage: 48VDC
Power Consumption: 192W
Nominal Amperage: .35 x 12 Amps
Power Output: 4-47VDC, 1050mA /Port (3x350mA)
Dimensions: 5.47”L x 2.87”H x 2.60”D
DNX IN Cable: 3-Pin, 24Gauge, 50’
Listing: UL / CE / RoHS
Power Supply DMX Driver
Operating Voltage: 120VAC
Output voltage: 48VDC
Power Consumption: 96W
Nominal Amperage: 2 Amps
Dimensions: 5.47”W x 2.87”H x 2.60”D
Listing: UL / CE / RoHS
Touch Interface
Trim: Steel, Polished Chrome Finish
Housing: Aluminum Housing, Glass Panel
Dimensions: 3-3/16”W x 4-15/16”H x 11/16”D
Loading: 2A per Channel, 6A in Total
Power Supply Touch Pad
Operating Voltage: 120VAC
Output voltage: 12VDC
Power Consumption: 48W
Nominal Amperage: 1.8 Amps
Dimensions: 2”W x 7”L x 1-1/4”H
Connector: 12V – 50’ Long
Brilliance Fixture
Type: LED RGB
Operating Voltage: 12VDC
Maximum Input Current: 350mA
LED: 1 x 3 Watt RGB in One
Beam Angle: 40°
Lumen: 88
Trim Finish: Polished Chrome
Housing Composition: First Grade Stainless Steel
Lens: Clear or Frosted, 7/8” Diameter
Lens Composition: Otpical Grade PMMA
Rough-in Cutout: 1-5/8”
Rating: IP68
Certifications: CE / RoHS / WEEE
Max Operating Temperature: 220°F when installed per instructions
Construction Template
Composition: Steel, Galvanized, Gauge 22
Dimensions: 15-1/8” L x 1/32” H x 3” D

Troubleshooting

The DMX driver will turn on automatically when supplied with power. The screen is always on. The screen will default back to A.001 after 15 of inactivity.
Warning: Do not change out lights with DMX driver power on.
Default Settings
Press enter then Up or Down to change if not showing default setting listed below then press back to save. If already showing default proceed to next step.

1. Press the Up button until A.001 displays. Press enter then Up or Down to change if not showing A.001 then press back to save. If already showing A.001 proceed to step 2
2. Press the Up button, CH12 should display.
3. Press the Up button, PF01 should display.
4. Press the Up button, BT16 should display.
5. Press the Up button, 9A1.0 should display.
6. Press the Up button, DP1.1 should display.
7. Press the Up button, Run1should display.

Enter Testing Mode

1. Press Down on the DMX driver until RUN1 displays then press Enter
2. Press up until RUN2 displays then press Back button.
3. Power Cycle DMX driver for at least 10 seconds. If you have 2 power supplies both will have to be unplugged at the same time.
4. Display should now read RUN2.

Zone 1
Red Zone 1 Channel 1

1. Press UP button until 01.00 displays then press Enter
2. Press Down until 01.FL displays.
3. Go to room and verify Red is working on all Zone 1 lights
4. Press Up then Enter then Up until 01.00 displays then press Back

Green Zone 1 Channel 2

1. Press UP button until 02.00 displays then press Enter
2. Press Down until 02.FL displays.
3. Go to room and verify Green is working on all Zone 1 lights
4. Press Up then Enter then Up until 02.00 displays then press Back

Blue Zone 1 Channel 3

1. Press UP button until 03.00 displays then press Enter
2. Press Down until 03.FL displays.
3. Go to room and verify Blue is working on all Zone 1 lights
4. Press Up then Enter then Up until 03.00 displays then press Back

Zone 2
Red Zone 2 Channel 4

1. Press UP button until 04.00 displays then press Enter
2. Press Down until 04.FL displays.
3. Go to room and verify Red is working on all Zone 2 lights
4. Press Up then Enter then Up until 04.00 displays then press Back

Green Zone 2 Channel 5

1. Press UP button until 05.00 displays then press Enter
2. Press Down until 05.FL displays.
3. Go to room and verify Green is working on all Zone 2 lights
4. Press Up then Enter then Up until 05.00 displays then press Back

Blue Zone 2 Channel 6

1. Press UP button until 06.00 displays then press Enter
2. Press Down until 06.FL displays.
3. Go to room and verify Blue is working on all Zone 2 lights
4. Press Up then Enter then Up until 06.00 displays then press Back

Zone 3
Red Zone 3 Channel 7

1. Press UP button until 07.00 displays then press Enter
2. Press Down until 07.FL displays.
3. Go to room and verify Red is working on all Zone 3 lights
4. Press Up then Enter then Up until 07.00 displays then press Back

Green Zone 3 Channel 8

1. Press UP button until 08.00 displays then press Enter
2. Press Down until 08.FL displays.
3. Go to room and verify Green is working on all Zone 3 lights
4. Press Up then Enter then Up until 08.00 displays then press Back

Blue Zone 3 Channel 9

1. Press UP button until 09.00 displays then press Enter.
2. Press Down until 09.FL displays.
3. Go to room and verify Blue is working on all Zone 3 lights.
4. Press Up then Enter then Up until 09.00 displays then press Back.

Zone 4
Red Zone 4 Channel 10

1. Press UP button until 10.00 displays then press Enter.
2. Press Down until 10.FL displays.
3. Go to room and verify Red is working on all Zone 4 lights.
4. Press Up then Enter then Up until 10.00 displays then press Back.

Green Zone 4 Channel 11

1. Press UP button until 11.00 displays then press Enter.
2. Press Down until 11.FL displays.
3. Go to room and verify Green is working on all Zone 4 lights.
4. Press Up then Enter then Up until 11.00 displays then press Back.

Blue Zone 4 Channel 12

1. Press UP button until 12.00 displays then press Enter.
2. Press Down until 12.FL displays.
3. Go to room and verify Blue is working on all Zone 4 lights.
4. Press Up then Enter then Up until 12.00 displays then press Back.

Returning to Run 1

1. Press Enter then press up until Run 1 displays.
2. Press Back
3. Power Cycle DMX driver for at least 10 seconds. If you have 2 power supplies both will have to be unplugged at the same time.
4. Display should now read 001

Notes
………………

www.Bathology.com
800-957-2862
A division of Bathing Brands,Inc.
Rev-06
12/23
Spectrum 511
900-0115-0415

References

• Bathology

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>