BATHOLOGY 441 Sauna White Light System Instruction Manual

BATHOLOGY 441 Sauna White Light System

Product Information

Specifications

• Product Name: Spectrum 441 Sauna White Light System
• Power Source: 120V AC Grounded
• Installation Requirements: Accessible, dry location
• Control: Light switch provided by others
• Warranty: Void if electrical components are hot swapped

Product Usage Instructions

Installation Considerations

Before proceeding with installation, carefully review all installation options and instructions. Follow these guidelines:

• Do not hot swap any electrical components to avoid voiding the warranty and product failure.
• Use safety goggles at all times for safety purposes.
• Disconnect the system from its power source before swapping any electrical components.
• All wiring must comply with the National Electric Code and local building codes.
• Installation should be done by a licensed, qualified electrician.
• Check for piping/electrical before cutting or drilling.
• Ensure light placement avoids direct contact with bather’s eyes.

Installation Steps

1. Install a standard single gang electrical box in an accessible, dry location.
2. Run a grounded 120VAC from the power supply to the electrical box.
3. For 2-6 lights Output Box installation:
   • Plug 1′ Cat6 cable into E and into A of Output Box.
   • Follow DIP switch settings for proper output configuration.

Package Contents

The package includes various items necessary for installation:

• Driver, Enclosure, Ground Connector, Screws/Anchors, Wire Nuts, Strain Relief Bushings, Male NEMA Cable, Light Cable, Mounting Template, Cat6 Cables, Brilliance Light Fixture, Wire Fit Cap, Silicone Sealant, etc.

Safety Precautions

• Avoid uninsulated electrical connections in the wall/ceiling area by using insulating gloves.
• Avoid placing the switch within reach of a tub or shower to prevent accidents.
• Ensure the fixture(s) are positioned to avoid direct contact with the bather’s eyes.

FAQ

Q: Can I install the Spectrum 441 Sauna White Light System myself?

A: It is recommended to have the system installed by a licensed, qualified electrician to ensure proper installation and safety compliance.

Q: What should I do if I encounter uninsulated electrical connections during installation?

A: Use insulating gloves to handle any risk of uninsulated electrical connections in your wall or ceiling area to prevent accidents or electric shocks.

Installation Considerations

Please read this manual in its entirely prior to installation

IMPORTANT: DO NOT HOT SWAP ANY ELECTRICAL COMPONENTS. This will void the warranty, and likely cause the product to fail.

CAUTION
Carefully review all installation options and instructions before proceeding.
For safety purposes, use safety goggles at all times.

WARNING
Do not hot swap any electrical components. This will void the warranty, and likely cause the product to fail. Fully disconnect the system from its power source before swapping any electrical components.

WARNING
Check for piping / electrical before cutting or drilling.

WARNING
Some electrical components are not waterproof.

WARNING
If there is any risk of uninsulated electrical connections in your wall/ceiling area, use insulating gloves.

WARNING
The Spectrum 441 Sauna White Light System can be controlled by the use of a light switch provided by others. NEVER place a switch where it can be reached from a tub or shower.

IMPORTANT
All wiring must be done in accordance with National Electric Code and local building code.

IMPORTANT

The Spectrum 441 White Light System should be installed by a licensed, qualified electrician.

IMPORTANT
Consider light placement carefully. The fixture(s) for this system should be placed to avoid direct contact with the bather’s eyes.

Installation

NOTE: Quantity with an * increases by one per each additional light purchased. Quantities shown assume no additional lights purchased with Spectrum 441 system.

1. Install a standard single gang electrical box in an accessible, dry location.

2. Run a grounded 120VAC from the power supply to the accessible, dry location ’s electrical box.
3. Secure enclosure (B) to wall in an accessible, dry location using provided screws/anchors.

4. Determine number of lights per input. Limit 6 lights per input.
5. Determine desired brilliance light fixture (J) location. Note: Fixture should be placed to avoid direct contact with the bather’s eyes. Allow for 2” clearance from insulation above and around the fixture.
6. Optional: Mount 16” location template (I) to ceiling / wall framework. Use notches to quickly align desired location to other fixtures in the room.

7. Make a 1-5/8” hole in desired location.
8. Mount brilliance light fixture (J) to ceiling through 1-5/8” cut – out. Allow for 2” clearance from insulation above and around the fixture.
9. Repeat steps 6 – 8 for each light.

Product Care

For routine cleaning, simply use a soft damp cloth and common household soap. Use a damp cloth to wipe clean, then dry. Clean product frequently to avoid calcium deposits on surfaces. Use only mild soap. Never use abrasive or cleaning containing alcohol, ammonia, hydrochloric or phosphoric acids as they may damage the product’s finish. T o clean electrical components, gently wipe down using a dry cloth or duster. Never use a wet duster , water, or any other liquid to clean the device.

Specifications

Driver

• Operating Voltage: 120 V AC Output

• Voltage: 700mA

• Power Consumption: 35W

• Nominal Amperage: 1.1 Amps

• Dimensions: 5-7/8” W x 1-1/8” H x 1-5/8” D
  Brilliance Fixture

• Type: LED White 3500K

• Operating Voltage: 12VDC

• Maximum Input Current: 700mA LED: 1 x 3 Watt

• Beam Angle: 35°

• Trim Finish: Polished Stainless Steel

• Housing Composition: First Grade Aluminum

• Lens: Frosted, 1-7/32” Diameter

• Lens Composition: Tempered Glass

• Rough-in Cutout: 1-5/8” to 1-11/16”

• Trim Dimension: 2-3/64” Diameter, 1/8” Profile

• Body Dimensions: 1-15/32” Diameter x 1-7/8” Deep

• Rating: IP68

• Certifications: CE / RoHS / WEEE
  Max Operating Temperature:
  220°F when installed per instructions
  Enclosure

• Housing Composition: Steel, black powder coated finish

• Dimensions: 7-3/4” W x 1-7/8” H x 4-7/8” D

• Standards: NEMA 1

• Listing: ETL, UL
  Construction Template

• Composition: Steel, Galvanized, Gauge 22

• Dimensions: 15-1/8” L x 1/32” H x 3” D

Replacement Parts

Contact your Bathology representative for Spectrum 441 Sauna White Light System replacement parts. 800-957-2862 www.Bathology.com

www.Bathology.com 800-957-2862
A division of Bathing Brands,Inc.

References

• Bathology

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>