allgood FI2450EL Modric Electronic Soap Sanitiser Dispenser Instruction Manual

Fixing Instructions – 2450EL, EF & ES FI2450EL Issue 02-08/22

Specifications

Foam type : 0.7-1.0 ml
Spray type : 0.8-1.1 ml
Applicable Viscosity Range| Liquid: 1-3000 cps (mPa.$)
Foam: 1-5 cps (mPa.$), Foaming soap only Spray: Ethanol solution only
Cover Type| Stainless Steel #316

Recommended Installation

DISTANCE (MINIMUM TYPICAL) NON-REFLECTIVE COUNTERTOP/SURFACE AREA At least 200 mm (7.87″)
REFLECTIVE/METAL COUNTERTOP/SURFACE AREA At least 300 mm (11.81′)

Installation

A. Tile or Dry Wall:

1. Tape the installation template at the appropriate location on the mounting surface.
2. Drill four (4) holes at marked locations 8 mm.
3. Insert four (4) plastic anchors (supplied) into drilled holes; remove template (fig. 1).
4. Insert two (2) screws (supplied) into top plastic anchors and leave 3 mm space from the wall under head (fig. 2 and fig. 3) for hanging dispenser.
5. Hang the dispenser on the two (2) screws through the keyhole slots at backplate top.
6. Use modric key to unlock and pull forward the housing cover (fig. 4 ).
7. Remove soap reservoir and lock dispenser to wall with remaining two (2) screws (supplied) through the holes at backplate bottom. Tighten all screws (fig. 5).

B. Adhesive on Mirror:

1. Clean mounting surface in area to be installed with isopropyl alcohol.
2. Mark outline of dispenser on mirror with masking tape.
3. Remove paper liners from self-adhesive pads on dispenser backplate.
4. Place unit on mounting surface with even steady pressure and hold for 1 minute.
5. Let tape cure for 10 hours prior to filling dispenser with soap for use.

BEFORE INSTALLATION:

1. Provide vertical, clean and smooth mounting surface.
2. Make sure there is enough room above dispenser to access cover lock key.
3. Ensure there are no obstructions below unit in sensor zone.
4. Check operation of unit while holding in place by hand BEFORE permanent installation.

After Installation Steps Check

1. Check to ensure that dispenser is firmly attached to mounting surface.
2. Check to ensure that correct viscosity soap is filled into reservoir.
3. Check to ensure that soap container cover is closed and air vent hole is not blocked.
4. Check to ensure that soap container is clean (no spill-over} and not leaking.
5. Check to ensure that cradle gate is latched on pump (lift, push and press down to engage pins to latch or unlatch in reverse operation).
6. Check to ensure that four (4) new Alkaline Type AA batteries are installed with correct polarity (note the +/- indication, fig. 6, and below, typical).
7. Check to ensure that the battery box plug is properly engaged with the cable and the compartment door is closed.
8. Check to ensure that the LED is lit blue and then flashes four (4) times by pushing up the cover safety interlock switch (blue stem) on bottom to click and hold it.
9. Check to ensure that the housing is properly locked and the security key is retained.

User’s Instructions

1. Place hand below the dispenser spout within the sensing range. The dispenser will automatically release the preset amount of liquid soap I foam soap / Spray soap from the nozzle spout.
2. Obtain additional soap by withdrawing hand and then again placing hand below the dispenser spout within the sensing range.

Sensing Range

Sensing is automatically controlled to set the appropriate distance for the triggering zone. This is based upon mounting height above the counter or floor and the ambient and reflected lighting conditions. There are no user adjustable controls for this feature. It is important to observe the guidelines in Section 4 (on reverse side of these instructions) and install unit above the minimum distance noted for each type of field condition. If lighting conditions change during the life of the installation the unit will automatically readjust itself to accommodate the new environment with no intervention by owner. Counter top reflective quality changes constitute a new environment condition and may require dispenser relocation to just above the appropriate minimum height as below.

 Improtant Notice

1. Ensure no bright source is aimed or reflected at the sensor from below.
2. Use fresh new liquid soap only and clean the soap container properly before each re-fill. Deposits of old soap will lead to malfunction and jamming.
3. When using foam soap pump, do not dilute liquid soap unless concentrate and do not use soap containing abrasive. Observe indicated viscosity factor of liquid soap.
4. Do not immerse the soap dispenser in water or clean it under running water. This will lead to short circuit.
5. Should the dispenser be out of order and batteries have been replaced, do not attempt any repair work. Call your dealer for professional assistance.

Batte Low Indication

With housing cover open and soap reservoir removed perform the following diagnostic test: 1. Press and hold the micro switch on the bottom of control box and hold it. 2. Observe that the LED is lit blue and then flashes four (4) times indicating proper operation °stand-by” condition and battery charge level. 3. If LED continues to flash blue the indication is positive to replace the batteries.

Troubleshootin

remains in the soap tank.
•Check the sensor cover to ensure nothing is obscuring the lens.
•Check the battery or if the power cord is not connected firmly.
•Check the pump and cap air hole for clogs.
Battery LED indicator flash| •Replace batteries
Dispensed volume decreased| Liquid Soap Type
•Check the soap level remains in the soap tank.
•Check if the pump is clogged with dried soap, if so, please rinse the pump with water.
•Check if the viscosity of the soap is higher than accepted range.
Foam Soap Type
•Check the soap level remains in the soap tank.
•Check if the filter (located inside the pump) is clogged.
•Check the soap type— only foam soap should be used, do not use liquid soap with foam soap pump.
Spray Soap Type
•Check the soap level remains in the soap tank.
•Check if the filter (located inside the pump) is clogged.
•Check the soap type— only liquid alcohol (cps less than 1) should be used.
Soap leaks| •Clean the soap tank and pump. For foam soap and spray type, please check if the filter (located inside the pump) is clogged.
•Check if the pump and tank are securely fitted/screwed together.
•Check if there are cracks on the pump. If so. Please replace the pump.
Solid blue LED indicator| •Check if the foam soap or spray type pump is clogged.

Diagram & Reair Parts list

1. Soap tank lid
2. Soap tank
3. Pump
4. Electronic box
5. Battery box
6. modric Release Key
7. Base plat
8. Cover

T:020 7387 9951
Recycle responsibly

Documents / Resources

| allgood FI2450EL Modric Electronic Soap Sanitiser Dispenser [pdf] Instruction Manual
FI2450EL Modric Electronic Soap Sanitiser Dispenser, FI2450EL, Modric Electronic Soap Sanitiser Dispenser, Electronic Soap Sanitiser Dispenser, Soap Sanitiser Dispenser, Sanitiser Dispenser, Dispenser
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>