airties AIR4960X Wifi 6 Smart Mesh Extender User Manual
- June 9, 2024
- AirTies
Table of Contents
- airties AIR4960X Wifi 6 Smart Mesh Extender
- Wi-Fi 6 Smart Mesh Extender
- INSTALLATION
- RETURNING TO FACTORY SETTINGS
- Trouble Shooting
- Revision Table
- Printing Colors
- Regulatory Statements & Safety Instructions
- Installation and Placement
- FCC Compliance
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
airties AIR4960X Wifi 6 Smart Mesh Extender
Wi-Fi 6 Smart Mesh Extender
Note: Please remove the protective plastic on the products before installation.
INSTALLATION
To install the Airties Wireless devices, please download “Airties Vision” application on your mobile device by Scanning this QR code. Please follow the instructions in the mobile application to complete your setup.
TIPS FOR BEST PERFORMANCE
Keep devices away from:
- Potential sources of electrical interference. Equipment that may potentially cause interference include home security systems, microwaves and consumer electronic devices.
- Large metal surfaces and objects.
- Sources and areas of heat such as ovens and sun rooms as well as direct sun light.
- Please make sure to remove the protective plastic on the device before first use.
- Please use the device in upright position. The openings are provided for ventilation, do not block or cover openings.
- Your device is designed to work indoors and under room temperature conditions only.
- Avoid placing the device to very cold, very hot, very humid or very dry locations inside your home.
- To change advanced settings on your device, you can access web Ul with the credentials below:
- Username: admin
- Password: Admin123
RETURNING TO FACTORY SETTINGS
To return the device to factory settings, press down on the reset button (in
the small opening on the back shown above) for 5 seconds and release.
A metal paperclip (with an extended tip) or strong toothpick are typically
good choices for this task. When the reset process is triggered, the LED in
the front will “blink rapidly” and the device will reboot to factory settings.
PRODUCT NOTICES
Operational modes:
- 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40),
- 802.11ax (HE20), 802.11ax (HE40)
- 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20),
- 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160),
- 802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80),
- 802.11ax (HE160)
Trouble Shooting
Condition | LED Color | LED Behavior | Timing |
---|---|---|---|
Power OFF | OFF |
Power ON, booting
|
White
|
Blinking
|
Wireless network healthy| Green| Blinking| 5O milliseconds OFF 5 seconds ON
Device configured as single
wireless access point
|
Green
|
Solid
|
Unconfigured mesh device| Blue| Blinking| 4 seconds OFF
4 seconds ON
Weak connection to the wireless mesh network| Red| Solid|
Cannot connect to the wireless mesh network|
Red
|
Blinking
| 1 second OFF
1 second ON
Software upgrade
|
Blue
|
Blinking
| 1/2 second OFF 1/2 second ON
Explanation| Recommended Action(s)
---|---
Device is turned off.| Make sure the power button on the back
is pressed and power supply unit is connected to the device.
| No action required. If the device was just powered on, please wait for at least
2 minutes for the device to boot up.
LED is steady green with a short blink every 5 seconds.| No action required.
Device is connected to the router/ gateway with an ethernet cable and acts as
a wireless access point.
No other mesh devices are configured
in the network.
|
No action required, more mesh devices can be added to the wireless mesh network if needed.
Device is not configured and connected
to the wireless mesh network.
| Configure the device using Airties Vision app.
| Bring device closer to another device in the wireless mesh network.
Device is part of wireless mesh network but unable to find any of its mesh
partners.| Make sure other device(s) that are part of the wireless mesh
network are
powered on and close enough to connect.
Device is retrieving the latest software.
| Wait for the upgrade to complete. Device will automatically start with the latest software.
Revision Table
Change Point
|
Ref. PN.
|
PN.
|
Part Description
|
Date
|
Change Notes
|
Author
---|---|---|---|---|---|---
| | MP-0000072762| QIG, 4960R, Generic, EN, Color, Single, R0, v0|
16.12.2020| Initial Release| MB
| MP-0000072762| MP-0000073984| QIG, 4960R, Generic, EN, Color, Single, R1,
v0| 24.02.2022| Changed Air 4960XR with Air 4960R and changed verdana font
with open sans| MB
| MP-0000073984| MP-0000074097| QIG, 4960R, Generic, EN, Color, Single, R2,
v0| 15.04.2022|
changed Power icon with On/Off text and changed 12 V —1A with __
| MB
Printing Colors
Attention!
Safety instructions must be FSC compliant, must contain at least 70% of
recyclable fibres. Ideally safety instructions must be recycled and
recyclable. Safety instructions must be printed with a 100% vegetal ink.
NOT PRINTING!
There ARE INFORMATION ABOUT CUTTING LINE AND FOLDING MARKS.
THIS PAGE NOT PRINTING!
THIS PAGE INFORMATION FORTHE PAGE FOLDING.
Regulatory Statements & Safety Instructions
The following instructions apply to the “Product” which includes:
Model No: Air 4960x, Air 4960XR and its accessories (cables, power
supply, etc.)
- Please read these guidelines carefully and keep the document for your reference. Product warranty is void if you do not follow the below guidelines
- WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool.
- WARNING: Avoid using this product during an (electrical storm. There may be a remote risk of electric shock from lightning.
- WARNING: The power plug is designed to act as a disconnect device. Ihe indoor power outlet must be easily accessible. This Product is intended for indoor use only.
- You must be careful when using the device near personal medical devices, such as pacemakers and hearing aids. All wireless products are sensitive to interference which may affect their performance.
- This device is not intended for use by young children.
- This device contains small parts which are a choking hazard.
RF Exposure: In line with RF exposure guidelines, the device must be used
at least 20cm away from the body Failure to observe these instructions could
result in RF exposure exceeding the relevant guidelines.
The product should not be used in areas that present a risk of explosion or an
explosive atmosphere. Such environments may include, but are not limited to,
petrol stations, boats, storage facilities and transportation units for
chemicals, and anywhere the air may contain chemicals or large quantities of
particles such as grain, dust, or metal.
Installation and Placement
- This product must not be installed or placed in a location subject to direct sunlight, direct heat or excessive moisture.
- This product must not be installed or used in areas that are not sufficiently ventilated or that build up excessive heat. Do not cOver or block the ventilation slots of the device.
- Use only approved accessories and power adapter.
- Do not connect with incompatible products or accessories.
Product Maintenance and Handling
- The only way to Completely turn off the power is to unplug the product. Always unplug before any kind of cleaning or maintenance of the product.
- Clean with a damp cloth, avoid aerosol and liquid cleaners.
- Handle the product carefully to avoid damage.
- Do not attempt to disassemble and repair the product, its power adapter, or cables.
- Never push objects of any kind into this device through any openings other than the “RESET” hole as they may touch voltage points or short cut parts which could result in fire, explosion, or electric shock and permanently damage the product or cause injury.
- Do not expose your device or its accessories to extreme temperatures, keep within the range of minimum 0° (32 F) and maximum 40° (104 F) degrees Celsius.
- Under the following conditions, your Product must be repaired by a qualified electrician:
- If the power adapter or cable is damaged.
- If the product has been exposed to rain or other moisture.
- If the product does not operate as expected when following usage instructions.
- If the product has been dropped or is visibly damaged.
- You notice a distinct change in performance that indicates a need for maintenance.
Hereby, Airties declares that this device is in compliance with Directive
2014/53/EU.
The full text of the EU Declaration of Conformity (DoC) is available at the
following internet address: https://airties.com/declarations-of-conformity
(Please click on the model to view the relevant document)
This equipment is subject to certain restrictions, 5150 too 5350 MHZ frequency
range is restricted to indoor use when it is used in the following countries:
Belgium (BE), Bulgaria (BG), Czech (CZ), Denmark (DK), Germany (DE), ESstonia
(EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italy
(TT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU),
Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT),
Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), United
Kingdom (Northern Ireland) (UK(NI), Turkey (TR), Norway (NO), Switzerland
(CH), Iceland (IS),
Liechtenstein (L). Compliance with 2014/53/EU Radio Equipment Directive
RED): In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency bands used and the maximum RF transmit power of Airties wireless products for sale in the EU:
Frequency Range | Channels Used | Max. Transmit power |
---|---|---|
2400-2483.5 | 1-13 | OFDM: 19,9dBm (97.7mW) |
CCK: 17,9dBm (61.7mW)
5150-5250| 36-48| 22,9dBm (19SmW)
5250-5350| 52-64| 22,9dBm (19SmW) with TPC
19,9dBm (97.7mW) without TPC
5470-5725| 100-140| 29,9dBm (977mW) with TPC 26,9dBm ( 490mW) without TPC
TPC = Transmit Power Control, a mechanism that reduces transmitting power
to minimize interference for nearby networks.
ENERGY CONSUMPTION INFORMATION in standby mode (According to the Guideline
2009/ 125/ EC of the European Parliament): 5.5W
Recycling of electrical and electronic equipment Product Recycling
This symbol indicates the obligation of separate collection of electrical
and electronic equipment differentiation
Hazardous substances contained in electrical and electronic equipment and
their improper use may have adverse effects on the environment and human
health. Once out of use, this product should be disposed of separately from
regular household waste streams.
Please follow your local and national guidelines for the responsible disposal
of electronicC waste when the and from other waste product’s lifecycle is
over.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
This product has been tested and complies with the specifications for a ClasS
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used according to the instructions, may cause harmful
interference to radioo communications. However, there is no guarantee that
interference will not occur in a particular installation. protection against
harmful.
If this equipment does cause harmful interference to radio or television
reception, which is found by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and devices
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult a dealer or an experienced radio/TV technician for assistance
FCC Caution
The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could
void the user’s authority to operate the equipment. 2.4GHz operation of this
product in the USA/CA is firmware limited to channels 1 through 11. This
device is restricted for indoor use.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body. This device and it’s antennas(s) must not
be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product
procedures.
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device,The device for operation in the band 5150-5250 MHz is
only for indoor use to reduce the potential for harmful interference to cO- channel mobile satellite systems.
IMPORTANT NOTE
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 22cm between the radiator & your body.
Open Source Software
The Product contains Open Source Software. Detailed information on the
applicable licenses and license terms can be found on the device’s user
interface.
To obtain a copy of said source code. Please contact
osrb@airties.com
Additional safety, compliance, recycling and other important information regarding your device can be reached at www.airties.com/sustainability
The use of Software or firmware not supported/provided by Airties products may result in the equipment no longer being compliant with the regulatory requirements.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>