airties 4960 Wi-Fi 6 Smart Mesh Access Point User Manual
- October 30, 2023
- AirTies
Table of Contents
airties 4960 Wi-Fi 6 Smart Mesh Access Point
The Air 4960 is a Wi-Fi 6 smart mesh access point with multiple ports and buttons for easy usage. The device has gigabit Ethernet ports, a WPS button, a power on/off button, a reset button, and an external power supply. It is designed to work indoors and under room temperature conditions only.
Ports and Buttons
- Status LED
- Gigabit Ethernet Ports
- WPS Button
- Power On/OFF Button
- Reset Button
- External Power Supply
Please remove the protective plastic on the device before installation.
Installation
To install the Air 4960, download the Airties Vision application on your mobile device by scanning the QR code provided. Follow the instructions in the mobile application to complete your setup.
Tips for Best Performance
For best performance, keep devices away from potential sources of electrical interference, large metal surfaces and objects, sources and areas of heat such as ovens and sunrooms as well as direct sunlight. Use the device in an upright position to allow for proper ventilation. Do not block or cover openings. Avoid placing the device in very cold, very hot, very humid, or very dry locations inside your home.
To change advanced settings on your device, access web UI with the credentials below:
- Username: admin
- Password: Admin123
Returning to Factory Settings
To return the device to factory settings, press down on the reset button (in the small opening on the back shown above) for 5 seconds and release. A metal paperclip (with an extended tip) or a strong toothpick are typically good choices for this task. When the reset process is triggered, the LED in the front will blink rapidly and the device will reboot to factory settings.
Product Notices
The Air 4960 supports the following frequencies:
- 2.4 GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HE20), 802.11ax (HE40)
- 5 GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80), 802.11ax (HE160)
Troubleshooting
Condition| Power OFF LED Color| LED Behavior| Timing| Explanation| Recommended
Action(s)
---|---|---|---|---|---
Power ON, booting| White| LED is steady green with a short blink every 5
seconds.| No action is required. If the device was just powered on, please
wait for at least 2 minutes for the device to boot up.
Wireless network healthy| Green| A device is configured as a single wireless
access point.| | The device is connected to the router/gateway with an
Ethernet
cable and acts as a wireless access point. No other mesh devices
are configured in the network.
Unconfigured mesh device| Blue| | | The device is not configured and connected
to the wireless mesh
network.
Weak connection to the wireless mesh network| Red| Blinking| 1/2 second OFF
1/2 second ON| The device is part of the wireless mesh network but unable to
find any of its mesh partners.
Cannot connect to the wireless mesh network| Red| Solid| |
Software upgrade| Blue| Blinking| 4 seconds OFF 4 seconds ON| The device is
retrieving the latest software.
PORTS and BUTTONS
Please remove the protective plastic on the products ! before installation
INSTALLATION
- To install the Airties Wireless devices, please download “Airties Vision” application on your mobile device by scanning this QR code.
- Please follow the instructions in the mobile application to complete your setup.
TIPS FOR BEST PERFORMANCE
Keep devices away from:
- Potential sources of electrical interference.
- Equipment that may potentially cause interference include home security systems, microwaves and consumer electronic devices.
- Large metal surfaces and objects. Sources and areas of heat such as ovens and sun rooms as well as direct sun light.
- Please make sure to remove the protective plastic on the device before first use.
- Please use the device in upright position.
- The openings are provided for ventilation, do not block or cover openings.
- Your device is designed to work indoors and under room temperature conditions only. Avoid placing the device to very cold, very hot, very humid or very dry locations inside your home.
- To change advanced settings on your device, you can access web UI with the credentials below:
- Username: admin
- Password: Admin123
RETURNING TO FACTORY SETTINGS
- To return the device to factory settings, press down on the reset button (in the small opening on the back shown above) for 5 seconds and release.
- A metal paperclip (with an extended tip) or strong toothpick are typically good choices for this task. When the reset process is triggered, the LED in the front will “blink rapidly” and the device will reboot to factory settings.
PRODUCT NOTICES
- Operational modes: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HE20), 802.11ax (HE40) 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.11ax (HE20), 802.11ax (HE40), 802.11ax (HE80), 802.11ax (HE160)
TROUBLESHOOTING
Condition| Power OFF LED Color| LED Behavior| Timing| Explanation| Recommended
Action(s)
---|---|---|---|---|---
Power ON, booting| White| LED is steady green with a short blink every 5
seconds.| No action is required. If the device was just powered on, please
wait for at least 2 minutes for the device to boot up.
Wireless network healthy| Green| A device is configured as a single wireless
access point.| | The device is connected to the router/gateway with an
Ethernet
cable and acts as a wireless access point. No other mesh devices
are configured in the network.
Unconfigured mesh device| Blue| | | The device is not configured and connected
to the wireless mesh
network.
Weak connection to the wireless mesh network| Red| Blinking| 1/2 second OFF
1/2 second ON| The device is part of the wireless mesh network but unable to
find any of its mesh partners.
Cannot connect to the wireless mesh network| Red| Solid| |
Software upgrade| Blue| Blinking| 4 seconds OFF 4 seconds ON| The device
retrieves the latest software.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>