AirTies Air 4920 Expansion Unit User Manual

AirTies Air 4920 Expansion Unit User Manual

PACKAGE CONTENT

PORTS AND BUTTONS

LED LIGHT BEHAVIOUR

B

| | No action required. If unit was just powered on, then please wait for at least 2 minutes for the unit to complete its boot process.
C| | No action required. Please wait.

D

| |

No action required.

E| | Bring the device closer to another device on the MESH network.
F| | No action required.
G| | No action required.

H

| This behaviour is temporary and lasts for about 5 seconds, after which the LEDs go to one of the following states:

1)    MESH with strong signal (state D), and

2)    MESH with poor signal (state E).

| If LED is red (state E) then bring device closer to another device on the MESH network.

If LED is green (state D) then no action required.

I

| Device has factory settings and is not connected to the home network in any way (e.g., the device is not wired to the gateway/modem/router).|

Configure device (refer to Quick Installation Guide).

J| First Access Point (wired to gateway/ modem/router).| No action required.

K

| Access Point is part of MESH, but unable to find any of its MESH partners.| Make sure the other device(s) that is/are part of the MESH network is/are powered on and close enough to connect.

L

| This behaviour is temporary and lasts for about 5 seconds, after which the LEDs go back to the state the device was in before the WPS attempt.| On failure, repeat WPS attempt after bringing the device closer to another device that is already on the MESH network (i.e. in state D).

ADDING THE EXPANSION UNIT TO AN EXISTING MESH
Please remove the protective plastic cover from the product before installation.

STEP 1
Open the AirTies Wi-Fi application on your mobile device.

STEP 2
Select My Network from the menu.

STEP 3
Click on + AirTies Unit

STEP 4
Follow the instructions on your mobile application to complete your setup. This process should only take a couple of minutes.

ALTERNATIVE
USING THE EXPANSION UNIT AS A STAND-ALONE ACCESS POINT

STEP 1
Connect the AirTies Expansion Unit to your existing network using an Ethernet cable.

STEP 2
Connect the supplied Power Adapter to the AirTies Expansion Unit and then into a power socket. Turn the unit on.

STEP 3

• To configure your AirTies Expansion Unit, open an Internet browser (Safari, Chrome, Firefox, Internet Explorer, etc.) on your device (PC, Laptop, Smartphone, Tablet, etc.). Enter “http://air4920.local” in the address bar. The device (PC, Laptop, Smartphone, Tablet, etc.) will present the AirTies Expansion Unit setup page.
• On the AirTies Expansion Unit’s setup page, insert the Wi-Fi Name (SSID) and Password, of your choice, and click “Save”. The pre-configured (factory) Wi-Fi Name (SID) and Password can be found at the bottom of the unit.
• You can now connect to the Wi-Fi using the Wi-Fi Name (SSID) and Password configured.

RETURNING UNITS TO FACTORY SETTINGS

To return the unit to factory settings, power on the unit, wait for the Power LED to be lit solid white, and press down on the reset button (in a small opening on the back) for 10 – 12 seconds. A metal paperclip is a good choice to do this. When the reset process is successfully triggered, the LEDs in the front will temporarily “blink” and the unit will reboot (in about 2 minutes) to factory settings.
Note: When returning meshed units to Factory Default state, all Access Points need to be reset within 2 minutes of resetting the first unit. If not, settings from the units that have not yet been factory reset will again overwrite the factory settings of the first unit.

PRODUCT SUPPORT

If you need assistance with any part of the setup, please do not hesitate to contact Nology Support at 010 980 0001 or alternatively, you can send an email to airties.support@nology.co.za. Our Office Hours are from 08:00 to 17:00 Monday to Thursday and from 08:00 to 16:00 on Fridays. This product makes use of software developed by the open- source community. Any such software is licensed under the specific license terms applicable to that particular software (like GPL, LGPL, etc.). Detailed information on the applicable licenses and license terms can be found on the device’s user interface. By using this product, you acknowledge that you have reviewed such license terms and that you agree to be bound by them. Where such terms entitle you to the source code of said software, that source code will be made available at cost upon request from AirTies. To obtain a copy of said source code, please send your request in writing via email to osrb@airties.com or via snail mail to:

AirTies Wireless Communications
AirTies will mail you a CD with the requested source code at the cost of CD preparation, shipping, and handling. For details please contact osrb@airties.com.

EU Declaration of Conformity

• Product: 1600 Mbps Video Grade Wireless Booster
• 1600 Mbps Smart Mesh Access Point
• Model: Air 4920
• Manufacturer: AirTies Wireless Networks
• Address : Mithat Uluünlü Sok. No:23 Esentepe Sisli, Istanbul/Turkey

We declare under our sole responsibility that this product complies with the relevant requirements of the following European Directives:

RED 2014/53/EU

                                      EcoDesign 2009/125/EC

RoHs 2011/65/EU

Signed for and on behalf of:

AirTies Wireless Networks The full text of the EU declaration of conformity is available at the following internet address: http://www.airties.com /declarations-of-conformity.html

Download PDF:AirTies Air 4920 Expansion Unit User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>