KEMPPI Zeta W200 Welding and Grinding Helmets User Manual

Zeta W200
Zeta W200x
Operating manual

Introduction

1.1 Zeta W200 and W200x
Zeta W200 and W200x welding helmets are designed for arc welding (MMA, MIG/MAG, TIG), grinding, gouging, and plasma cutting.
Zeta W200 and W200x welding helmets provide the users with protection for the eyes and face. The helmets are equipped with auto-darkening filter ADF SA 60Z, and the Zeta W200x model has also integrated LED work lights.
1.2 About this manual
Read this manual carefully before using the equipment for the first time. Pay particular attention to the safety instructions.

| Note| Gives the user a piece of information of particular importance.
---|---|---
| Caution| Describes a situation that may result in damage to the equipment or system.
****| Warning| Describes a potentially dangerous situation that may result in personal damage or fatal injury.

1.3 Disclaimer
While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. Kemppi reserves the right to change the specification of the product described at any time without prior notice. Do not copy, record, reproduce or transmit the contents of this guide without prior permission from Kemppi.

Safety

Warning:

• It is strictly forbidden to use any other than Kemppi branded parts or accessories with Kemppi’s personal protection equipment.
  If you do not respect this safety regulation, serious damage for your health may occur.

• We recommend a usage period of 5 years. The period of use depends on various factors such as use, cleaning, storage and maintenance. Inspect the helmet before each use. Replace damaged or worn parts.

• Use all adjustment features for maximum protection.

• Never weld with the welding visor up or without the

• welding filter.

• If the auto-darkening filter (ADF) does not darken when the arc ignites, stop welding immediately.
  Inspect the ADF and its power supply. Change if necessary.

• Always use welding filters together with suitable protection plates.

• Never use welding filter without inner protection plates.

• Never use a scratched or damaged welding filter and ocular.

• Materials which may come into contact with the wearer’s skin may cause allergic reactions to susceptible individuals.

• Only operate this product within the temperature range -5…+55 °C.

• The product is not intended for use in environments with a risk of explosion.

• The helmet does not protect against explosive devices or corrosive liquids.

• The helmet is not suitable for laser welding and oxyacetylene welding/cutting processes.

• The helmet gives designed protection against high speed particles only at room temperature (EN175 designation B) and only when all helmet components are properly attached, as described in the manual.

• When helmet is worn over any spectacles, they may transmit the impact of high speed particles, thus creating a hazard to the wearer.

• If the symbols of the marking are not common to different parts of the protection equipment, the lower protection level shall be assigned to the complete protection equipment.

Parts 1 2 3 4 5

1. Opening/closing tightness adjuster
2. Grinding mode (clear view) button
3. LED work lights (W200x model only)
4. Protection plate release button
5. Protection plate
6. Auto-darkening welding filter (ADF SA 60Z)
7. Inner protection plate
8. Headband, adjustable
9. Sweatband, washable
10. LED work light Li-ion battery unit (W200x model only)
11. ADF: Shade adjustment
12. ADF: Sensitivity adjustment
13. ADF: Delay adjustment
14. ADF: Operation mode selector (Cut/Grind/Weld)
15. ADF: Battery connection
16. ADF battery and battery holder
17. Distance slide adjusters (connect the headband to the helmet and adjust the distance of the helmet from the face)
18. Viewing angle adjuster.

Using helmet features

4.1 Taking into use 6

1. Adjust the helmet for your head:
   A. Use the top bands to adjust how deep the helmet sits (a).
   B. Use the distance slide adjuster to change the distance of the helmet from your face (b).
   Ensure that the helmet is comfortably as close as possible to your face and that both sides are equally positioned.
   C. Turn the knob in the rear to tighten and secure the headband (c).

2. Adjust the helmet’s opening/closing tightness if needed (d).

3. Turn the viewing angle adjuster to tilt the viewing angle upwards or downwards (e).

4.2 Using work lights (W200x) 7
Zeta W200x helmet has LED work lights that are powered by a rechargeable Li- ion battery unit on the neckband.

1. Press the battery test button on the battery unit to check the battery level.
2. For charging, remove the battery unit from the helmet and charge the battery using the unit’s USB-C connection and charging cable (charger not delivered with the product).
3. Insert the battery unit into the battery holder in the headband and connect the LED work light cable to it.
4. Use the OFF/AUTO/ON selector to turn the lights on and off. The AUTO mode turns the lights off in bright conditions (e.g. during welding) and then back on.
   Caution: Never use a damaged battery unit.
   The LED light battery unit is not waterproof.
   Avoid exposure to extreme temperatures, direct sunlight, moisture, sand and dust.
   Observe the battery unit while charging. If the battery unit becomes hot, smokes or there are visible deformations in the battery unit during charging, stop charging immediately.

4.3 Using quick grinding view 8
The Zeta W200/W200x helmet’s auto-darkening welding filter (ADF SA 60Z) can be switched to the grinding mode also by long-pressing the weld/grind mode button on the
side of the helmet.
To return to welding mode, only short press is needed.

Replacing parts

5.1 Removing headband 5

1. Press and hold down the distance slide adjuster (17).
2. Push the headband connector forwards, out of the distance slide adjuster.

5.2 Attaching headband 5

1. Bring the headband connector in front of the distance slide adjuster (17).
2. Press down the slide adjuster button while pushing the headband connector through the distance slide adjuster.
3. Slide the headband connector in place so that the slide adjuster pin locks into one of the grooves in the headband connector.
4. Adjust the helmet distance from your face.

5.3 Replacing outer protection plate 2

1. To remove the outer protection plate, press the fastener release button on the right and pull the protection plate out.
2. To install the outer protection plate, place it on the left fastener first and then snap the right side in place.

Note: Make sure both sides are properly aligned and in place.

5.4 Replacing inner protection plate 9

1. To remove the ADF inner protection plate, pull the bottom of the plate out slightly and slide the plate out from below.
2. To install the inner protection plate, slide the plate up into the grooves in the ADF. Make sure the plate snaps into place properly.

Maintenance

Inspect the helmet after each use. Replace worn or damaged parts.

6.1 Cleaning

• Clean the protection plate with mild soap, lukewarm water and a soft cloth.
• Wipe the welding filter lens with a soft, clean cloth, if necessary.
• Detach and wash the sweatband, if necessary.

Storage

Store the Zeta helmet in an environment with temperature between -20…+50 °C and humidity < 80 % Rh.
Store and transport the helmet and the accessories in the original bag or package.

Technical data

EN 175:1997-08, Personal protection. Equipment for eye and face protection during welding and allied processes
EN 166:2002-04, Personal eye protection, specifications
AS/NZS 1337.1:2010
AS/NZS 1338.1:2012
Type inspected by:| ECS European Certification Service GmbH. HlittfeldstraBe 50, 73430 Aalen, Germany. Notified Body No. 1883.
UKCA; SGS United Kingdom Limited, Rossmore Business Park Ellesmere Port South Wirral Cheshire CH65 3EN. Approved Body No. 0120
SAI Global Certification Services Pty Limited. 680 George Street, Sydney NSW 2000, GPO Box 5420 Sydney NSW 2001, Australia.
Manufacturer:| Kemppi Oy
PL 13, Kempinkatu 1, 15801 Lahti, Finland
Operating temperature:| -5…+55 °C
Recommended humidity for use:| < 80 % Rh
Storage temperature:| -20…+50 °C
Materials:| Plastics: PA, PP, PC, ABS, POM
Sweatband material 100 % cotton, padding foam plastic
Weight:| Zeta W200: 517 g, Zeta W200x: 658 g
LED work light| Zeta W200x only
---|---
Battery cell type:| Li-ion 3.65 V, 4 Ah, 14.6 Wh, rechargeable
Charging connector type:| USB-C
Battery life:| 8 hours
Battery charging temperature:| 0…+45 °C
Welding filter| ADF SA 60Z
---|---
Welding filter type:| Auto-darkening, factory-installed
Operating temperature range:| — 5 … + 55 °C <80% Rh
Storage temperature range:| — 20 … + 50 °C <80% Rh
Manufacturer:| Kemppi Oy
PL 13, Kempinkatu 1, 15801 Lahti, Finland
ADF switching time:| 0.1 ms
ADF light state:| Shade 2.5
ADF UV/IR protection:| Protection at all times
Battery, replaceable:| 1 x CR2450
Materials:| Plastics: PA, PC; Glass

Helmet and ocular markings

Eg. 2.5/8-12 KMP 1/1/1/1/379

Ordering codes

Welding helmet weight
**** See information supplied by the RPD manufacturer
Declarations of Conformityhttps://kemp.cc/zeta-w/ud
userdoc.kemppi.com
Zeta W200/W200x

References

• Redirecting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>