VOLTME Innovations MagPak 5K Magnet Battery Charger User Guide
- June 2, 2024
- VOLTME Innovations
Table of Contents
VOLTME Innovations MagPak 5K Magnet Battery Charger
Overview
- Battery Level Indicator
- Wireless Charging Indicator
- Power Button
- USB-C Port
- Fold-Out Stand
MagPak 5k Status Indicators
Charging Your iPhone 12 Series or Later
To activate wireless charging, press the power button or place your device on the charger as illustrated below and it will be held in place magnetically.
Built-in Foldable Magnetic Phone Stand Can be Used During
Charging.
Press & hold the power button for 3 second to switch off your
MagPak 5K.
Charging Simultaneously for Your Device and MagPak 5K
MagPak 5K will first fully charge the device, then charge itself.
Wireless Charge Your Phone and Other Devices First, press the
power button and align your device with the magnetic charging area. When the
wireless charging indicator lights up, the device is ready to begin charging.
*Not support Apple Watch charging.
If Your Device Stopped Charging at 80%
Your iPhone might get slightly warmer while it charges wirelessly this is the
normal situation of power conversion. If the battery gets too warm, software
might limit charging above 80%. Your iPhone will charge again when the
temperature drops.
FRIENDLY NOTICE
Charging Your Phone or Earbuds
Using a Charging Cable
MagPak 5K is equipped with a USB-C port and supports power output. Use the correct cable to charge your device.
Double-press the Power Button to Enter Low-current Charging
- Use a charge cable to connect a low-current device such as Bluetooth headset, Watch, or Smart band to MagPak 5K’s USB-C port.
- Double-press the power button to enter low-current charging mode. In low-current charging mode, the indicators flash in sequence.
- Double-press the power button again or press and hold the power button for 3 seconds to exit the mode, or wait for about 3 hours to automatically exit the mode.
*It is recommended that you press the power button to manually exit the mode after you have finished using it. If the device is still not fully charged after 3 hours, double-press the power button again to continue charging.
Recharging Your MagPak 5K
FOD: Foreign Object Detection
The indicator light will flash when foreign objects or devices that do not support wireless charging are detected by the sensor.
Specifications
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC Caution:
Radio Standards Specification RSS-Gen, issue 5
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF exposure statement:
The device has been evaluated to meet general RF exposure requirement The
device can be used in portable exposure condition without restriction.
Attention
- Avoid extreme temperatures.
- Avoid expose to liquids.
- Avoid dropping.
- Don’t disassemble
Customer Service
18-month limited warranty
Lifetime technical support
(US) +1(888) 643 8838
Mon-Fri 9:00 AM- 5:00 PM(PT)
(PE+86 755 285 100 14
-E3H 9:00 – 17:30
support@voltme.com
Shenzhen Voltnex
Innovations Technology Co., Ltd
Room 3101, Tower 6, Tianan Cloud Park ll,
Bantian Street, Longgang District, Shenzhen,
Guangdong, 518129, China
Follow us on social media for product information and warranty service:
@Voltme_Official
Voltme.com
support@voltme.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>