EPSON P6570D 44-Inch Wide-Format Dual Roll Printer User Guide

EPSON P6570D 44-Inch Wide-Format Dual Roll Printer

**Start Here**

IMPbORTANT: Before using this product, make sure you read these instructions and the safety instructions in the online User’s Guide.
The illustrations show the SureColor P8570D, but the steps are the same for all models, unless otherwise specified.

Choose a Location for the Printer

Choose a location for the printer that is near a wall outlet where the power cord can be easily unplugged. Avoid places subject to rapid changes in temperature and humidity. Also keep the printer away from direct sunlight, strong light, or heat sources.

Make sure to place the printer on a flat, stable surface capable of supporting approximately 275 pounds (124.7 kg) (SureColor P6570E), 291 pounds (131.8 kg) (SureColor P6570D/P6570DE), 395 pounds (179 kg) (SureColor P8570D), or 440 pounds (199.5 kg) (SureColor P8570DL) and with enough space on all sides (see illustration below).
7.67 in. (195 mm)

Model| W| D1 (Roll Paper)| D2 (Cut Sheets/ Poster Board)
---|---|---|---
SureColor P8570D/P8570DL| 78.46 in. (1993 mm)| 44.48 in. (1130 mm)| 157.48 in. (4000 mm) maximum
SureColor P6570D/ P6570DE/P6570E| 59.44 in. (1510 mm)

Note: If you are loading rigid poster board, the printer must be at least 30 inches (762 mm) away from the wall.

Unpack and Place Printer

1. Make sure you have these items:
   

2. Remove the outer carton from the pallet and printer and carefully lift the printer off of the pallet.
   WARNING: The printer requires four people to lift and move it. Make sure to grip the printer as shown in the illustration.
   

3. Remove the protective plastic and all tape from the outside of the printer.

4. Lock the front casters by pushing the tabs down.
   

5. Secure the two adjustable feet on the back of the printer.
   
   Note: Turn the adjustable feet by hand until they touch the floor. If you turn them 180° or more after they touch the floor, print quality may decline.
   

6. Remove the protective film from the touchscreen.
   
   Note: The touchscreen will not operate if you do not remove the protective film.

7. Open the top covers and remove the protective film from the print head and any tape and protective material inside.
   

8. Close the top covers.
   

9. Remove the tape from the front of the printer and the paper catch basket.

10. Open the ink cover and remove any protective material inside.
    Note: Make sure to open all compartments and remove all tape and protective materials from inside the printer before turning the printer on. Otherwise, you may not be able to print

Turn On and Configure

1. Connect the power cord to the back of the printer and plug the other end into an outlet.
   
   Note: If you are using the SSD (Solid State Drive) or Adobe ® Embedded Print Engine options, make sure to install them in the expansion slots on the back of the printer before turning the printer on. (The Adobe Embedded Print Engine is an option for the SureColor P6570DE/P6570E; it is pre-installed for all other models. The SSD unit is an option for all models.)

2. Press the power button on the control panel to turn on the printer.
   

3. Select your language, date, and time on the touchscreen.
   Note:
   • You can change these settings later using the product’s control panel. For more information, see the online User’s Guide.
   • If an error code appears, turn off the printer and check that no protective material has been left inside.

4. Follow the instructions on the touchscreen to begin ink initialization.

Install Ink Cartridges (SureColor P6570D/ P6570DE/P6570E/P8570D)

Caution: Keep the ink cartridges out of the reach of children and do not drink the ink.
Note:

• The printer is designed for use with Epson ® cartridges only, not third-party cartridges or ink.
• The cartridges included with the printer are designed for printer setup and not for
  resale. After some ink is used for initializing, the rest is available for printing.

1. Open the ink cartridges and shake them as shown for 10 seconds, or about 30 times.
   
   Caution: Do not touch the green chip on top of the cartridge. Doing so may prevent normal operation and printing.

2. Open the ink cover.
   

3. Insert the cartridges in the slot for each color as described on the label inside the ink cover. Push the cartridges in until they click.
   
   Note: Make sure all of the ink cartridges are properly inserted in the product; otherwise printing is not possible.

4.  Close the ink cover.
   

5. The printer begins charging the ink delivery system. This takes about 23 minutes. When you see a message on the touchscreen to load paper, ink charging is complete.
   Caution: Do not turn off or unplug the printer or perform any other operations during ink charging.
   Note:
   • You may need to replace the maintenance box (part number C13S210115) soon after ink initialization. See the online User’s Guide for instructions.
   • See the online User’s Guide for instructions on loading paper.

Install Ink Supply Units (Ink Packs) (SureColor P8570DL)

Caution: Keep the ink packs out of the reach of children and do not drink the ink.

1. Slide the lock switch to the right to unlock the ink tray.
   

2. Pull the ink tray out of the ink slot.
   

3. Insert the ink pack into the tray and push it down as shown.
   Note: Make sure the ink pack fits onto the pegs and is aligned with the top of the tray.
   

4. While the ink pack is in the tray, carefully shake it by tilting it up and down at about a 60 degree angle as shown.
   

5. Match the color on the ink pack label with the color slot on the printer and insert the ink tray into the printer.
   
   Note: The ink packs are keyed to fit into the correct color slot. If you cannot insert the ink tray all the way, do not force it. Make sure the ink pack color matches the color slot on the printer.

6. Slide the lock switch to the left to lock the ink tray. Repeat steps 1 to 6to install the other ink packs.
   

7. Follow the instructions on the touchscreen to begin ink charging. When you see a message on the touchscreen to load paper, ink charging is complete.
   Note: Make sure all of the ink trays are inserted in the product; otherwise printing is not possible.

Caution: Do not turn off the printer, load paper, or open any covers while the printer\ is charging or you’ll waste ink.
Note: See the online User’s Guide for instructions on loading paper.

Install Software

Note: An internet connection is required to obtain the product software.

1. Download and run your product’s software package. For the latest software, visit http://epson.com/support (U.S.),
   http://epson.ca/support (Canada), or http://latin.epson.com/support (Caribbean) and search for your product.

2. Follow the instructions on the screen to run the setup program.

3. When you see the Select Your Connection screen, select one of the following and follow the on-screen instructions:
   • Wired network connection
   Make sure you have an Ethernet cable (not included).
   • Wireless connection
   In most cases, the software installer automatically attempts to set up your wireless connection. If setup is unsuccessful, you may need to enter your network name (SSID) and password.
   • Direct USB connection
   Make sure you have a USB 2.0 or 3.0 cable (not included).
   Note: If you do not use a USB 2.0 or 3.0 cable, print speed and performance may decline.

Mobile Printing

Connect wirelessly from your smartphone, tablet, or computer. Print documents
and photos from across the room or around the world:

• Print directly from your iOS device. Simply connect your printer and device
  to the same network and tap the action icon to select the print option.

• Turn your mobile device into an intuitive, easy-to-use printing control
  center with Epson Smart Panel®. Download the app from your mobile device’s app store.

• Print directly from your AndroidTM (v4.4 or later) device*. Simply connect your printer and device to the same network and tap the menu icon to select the print option.

• May require the Epson Print Enabler or Mopria Print Service app from Google Play™.

Using the Touchscreen

1. Accesses printer settings
2. Feeds or cuts media
3. Turns on or off the printer’s interior light
4. Switches the screen view to display additional information
5. Displays maintenance settings
6. Displays the network connection status
7. Displays the printer’s status
8. Opens platen to remove jammed paper
9. Displays the Help menu
10. Displays network folder options
11. Selects paper size and type settings

Product Support

User’s Guide

Windows® : Click the icon on your desktop or Apps screen to access the online
User’s Guide.

Mac: Click the icon in Applications/Epson Software/Guide to access the online
User’s Guide.
If you don’t have a User’s Guide icon, go to the Epson website, as described in “Epson technical support.”

Epson technical support

Visit http://epson.com/support (U.S.), http://epson.ca/support (Canada), or http://latin.epson.com/support (Caribbean) and search for your product to download software and utilities, view manuals, get FAQs and troubleshootingadvice, or contact Epson.

Epson provides technical support and information on the installation, configuration, and operation of professional printing products through the Epson PreferredSM Limited Warranty Plan. Dial (888) 377-6611, 7 AM to 4 PM, Pacific Time, Monday through Friday. Days and hours of support are subject to change without notice. Before you call, make sure you have your:

• Printer serial number: ____
• Proof of purchase and date: ____

Note: If you experience difficulty with the toll-free line, call (562) 276-1305.

Recycling

Epson offers a recycling program for end of life hardware, ink packs, and ink cartridges. Please go to http://epson.com/recycle (U.S.) or http://epson.ca/recycle (Canada) for information on how to return your products for proper disposal.

Need Ink?

You can purchase ink from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).

SureColor P6570D/P6570DE/P6570E/P8570D replacement ink cartridges

SureColor P8570DL replacement ink packs

Options and replacement parts

C12C937711
Production Stacker (44″) (SureColor P8570D/P8570DL)| C12C937131
Production Stacker (24″)

(SureColor P6570D/P6570DE/P6570E)

| C12C937731
Adobe Embedded Print Engine*| C12C936151

• Optional for SureColor P6570DE/P6570E; included for all other models.

EPSON, Epson Smart Panel, and SureColor are registered trademarks and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
Epson Preferred is a service mark of Epson America, Inc.
Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
Mac is a trademark of Apple Inc., registered in the U.S. and other countries.
Android and Google Play are trademarks of Google LLC.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2022 Epson America, Inc., 5/22

References

• Epson® Official Support
• Epson® Official Support
• Recycling Program - For Printers, Hardware, Ink Cartridges | Epson Canada
• Recycling Program - For Printers, Hardware, Ink Cartridges | Epson US
• Epson

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>