VIZULO 66712 Shell Basic LED Luminaire Instruction Manual

June 3, 2024
VIZULO

VIZULO logo 66712 Shell Basic LED Luminaire
Instruction ManualVIZULO 66712 Shell Basic LED
LuminaireVIZULO 66712 Shell Basic LED Luminaire icon
13 20-05-2022 SIA VIZULO
Laucu Lejas, Iecava, Latvia, LV-3913
www.vizulo.com

VIZULO Shell Basic LED luminaire

Mounting instruction
Dimensions
VIZULO 66712 Shell Basic LED Luminaire fig
18 Mounting hole location

VIZULO 66712 Shell Basic LED Luminaire fig 19

Netto WeightVIZULO 66712 Shell Basic LED Luminaire fig
17

WARNING!

  • Do not touch LED modules!
  • Do not put any tools or other items on LED modules!
  • In case any LED is physically damaged (example shown below) the warranty is void.

VIZULO 66712 Shell Basic LED Luminaire fig 15 Install LED luminaire only in a clean room using gloves!
Diffuser cover may accumulate small electrostatic charges that makes it susceptible to dust and other small particles;
It should only be cleaned using dry microfiber cloth or compressed air duster.VIZULO 66712 Shell Basic LED Luminaire fig 14VIZULO 66712 Shell Basic LED Luminaire fig
13

User manual of microwave motion sensorVIZULO 66712 Shell Basic LED
Luminaire fig 12

Settings:

  1. Sensitivity Sensitivity can be adjusted by selecting the combination on the DIP switches for different applications.
    VIZULO 66712 Shell Basic LED Luminaire fig 11

  2. Hold-time Hold-time refers to the time period that the light remains 100% on if no more movement is detected.
    VIZULO 66712 Shell Basic LED Luminaire fig 10

  3. Daylight sensor Different daylight threshold can be preset on DIP switches. Light will always turn on upon movement if daylight sensor is disabled.

VIZULO 66712 Shell Basic LED Luminaire fig 9

Settings (Remote Control)

VIZULO 66712 Shell Basic LED Luminaire fig 8Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.

  • Press button “AUTO”, “RESET” to quit this mode. The mode will change to AUTO Mode after power failure.
    Reset Settings
    Press button “RESET”, all settings go back to default settings.
    Shift Button
    Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
    All values / settings in RED are valid for 20 seconds.
    AUTO mode
    Press button “AUTO” to initiate automatic mode. The sensor starts working and all
    settings remain as before the light is switched ON/OFF.
    SEMI-AUTO mode
    First press button “Shift” then “SEMI-AUTO” to initiate semi-auto mode. The fixture is manually on by push-switch and automatically off in this mode.
    Power output
    Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
    Note: “Sensor off” and “Twilight” functions are disabled.
    Brightness +/-
    Press the buttons to adjust the light brightness during hold-time.
    Scene program – 1-key commissioning

    1. Press button “Start” to program.
    2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all parameters.
    3. Press button “Memory” to save all the settings programmed in the remote control.
    4. Press button “Apply” to set the settings to each sensor unit(s).

For example, to set detection range 100%, daylight threshold Disable, hold- time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be: Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all settings are passed on the sensor(s).
Detection range (valid for master only)
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Daylight threshold
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux / 10Lux /50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note:

  1. To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button first
  2. These buttons are invalid for HCO34RF.

Ambient daylight threshold

  1. Press button “Shift”, the red LED starts to flash.
  2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.

Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s /30s/ 1min /5min /10min / 15min / 20min / 30min.
Note:

  1. To set hold-time at 30s / Smin / 15min / 30min, press “Shift” button first
  2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.

*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “Os” means on/off control; “4-00” means bi-level control, if daylight threshold is disabled or natural light is insufficient, the fixture is 100% on when there is motion detected, and remains at the stand-by dimming level after motion hold-time.
Stand-by dimming level
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10%/ 20%/ 30%/ 50%.
Auto-configuration function
All buttons in this zone are disabled.
Dual tech & RF mode
“HF”,”PIR”, “HF+PIR”, “HF/PIR” are disabled.
For RF grouping via remote control, please refer to steps below:
RF grouping
Short press “Learn/Erase” button on RC to activate pairing mode, and the receiver unit starts to beep once every second for 3min.
Note: the unit can only pair up to 30 units.
Short press “Transmit” button on RC, the commander unit (master unit) beeps one time to send the transmission signal.
Upon receiving the transmission signal, the receiver unit (slave unit) rapidly beeps 3 times in 1s to indicate the success of pairing. Repeat this step to pair more units.
One more short press on “Learn/Erase” button to the receiver unit to complete the pairing process, the receiver unit will quit the pairing mode.
Note: Press button RX100%, the light on receiver unit is 100% on upon receiving RF on signal; Press “RX STBY%” button, the light(s) goes to preset stand-by dimming level directly.
Erase:
Long press “Learn/Erase” button for 3s to the sensor unit. The beeper beeps rapidly for about 5s. All commands received before are erased.

VIZULO 66712 Shell Basic LED Luminaire fig 7

Master /Salve configurationVIZULO 66712 Shell Basic LED Luminaire fig
6

Tridonic LED driver

MCB/Inrush current table

Power range| Dimming| In-rush current (peak/duration)| B10A| B13A| B16A| B20A| C10A| C13A| C16A| C20A
7 – 10 W| DALI| 15 A (243µs)| 24| 31| 38| 48| 40| 56| 64| 80
Non dimmable| 17A (231 µs)| 23| 30| 37| 47| 38| 50| 61| 78
11- 17 W| DALI| 18 A (140 µs)| 22| 30| 36| 46| 36| 50| 60| 76
Non dimmable| 15 A (204 µs)| 25| 33| 40| 50| 41| 55| 66| 83
18 – 28 W| DALI| 25 A (141 µs)| 19| 24| 31| 40| 31| 40| 51| 66
Non dimmable| 16A (229 µs)| 25| 32| 39| 50| 41| 53| 65| 83

OSRAM LED driver

MCB/Inrush current table

Power range| Dimming| In-rush current (peak/duration)| B10A| B13A| B16A| B20A| C10A| C13A| C16A| C20A
7 – 15 W| DALI| 8 A (150 µs)| 38| | 60| | | | |
Non dimmable| 5 A (45 µs)| 82| | 130| | | | |
16 – 28 W| DALI| 13 A (225 µs)| 20| | 30| | | | |
Non dimmable| 20A (50 µs)| 50| | 80| | | | |

User manual of PIR motion sensor

VIZULO 66712 Shell Basic LED Luminaire fig 5

Settings (Remote Control HRC-12, for HIR02/RC12 & HIR04/RC12 & SAM13/RC12)
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.

  • Press button “AUTO”, “RESET” or “Ambient” to quit this mode.
    The mode will change to AUTO Mode after power failure.
    Reset Settings
    Press button “RESET”, all settings go back to default values.
    Sensor mode
    Press “Auto Mode” button, the sensor starts to function and all settings remain the same as the latest status before the light is switched on/off.
    SEMI-AUTO mode

Press button “SEMI-AUTO” to initiate semi-auto mode. The fixture is manually turned on by pressing the push-switch, and goes off automatically after hdd time. (Absence detection mode)
Daylight threshold
Press buttons in zone ” Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 1 00Lux / 300Lux / 500Lux / Disable.
Ambient daylight threacshold Press button “Ambient”, the surrounding lux level is sampled and set as theew daylight threshold.
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 5sec / 1min / 5min / 10 min / 15min / 30min / 60min. *To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Energy efficiency class of contained light source(s)VIZULO 66712 Shell
Basic LED Luminaire fig 4

Indoor Luminaire cleaning
Possible cleaning equipment
VIZULO 66712 Shell Basic LED Luminaire fig
3

It is important to clean luminaires in association with luminaire mounting or component changing. Refiective parts surfaces should be cleaned from dust and grime pollution.
It is also important to remember that the voltage should be disconnected before the cleaning process is initiated. Electrical components and cables must not be exposed to
water or detergents.
Information about luminaire’s components disassembling can be found in user’s instructionsVIZULO 66712 Shell Basic LED Luminaire icon
1

VIZULO 66712 Shell Basic LED Luminaire fig 2

Switch off power supply.| Wash and wipe the outside part.| Clean the inside of luminaire.
VIZULO 66712 Shell Basic LED Luminaire fig 1
Do not touch or wet LED modules.| Close the luminaire tightly.| Make function test.

Luminiare body
Vacuuming with a soft brush. Neutral dishwashing detergent with lukewarm water / Cleaning detergent, without grinding effects, in lukewarm water. Drying: Self-drying in room temperature or wipe off with a slightly damp cleaning cloth.
Reflector and diffuser cover
In case of loose dirt clean with soft duster or cleaning cloth without microfibers, or use a compressed air . For light soiling dilute a citric acid based cleaning product with water (e.g. 30 ml Frosch® citrus cleaner in 5 litre of water). Cleaner should be non-abrasive, pH neutral, alcohol-free. In case of heavy soiling: Oil and grease can be removed using a mixture of alcohol and water (1:1), e.g. methylated spirits. Residues of alcohol based cleaning products are easily wiped away with a water-soaked cotton cloth. Stubborn stains can be soaked in diluted citrus cleaner. Drying: Blow-off with compressed air or use a lint-free, fresh and clean cotton cloth.
Plastic covers and caps
Vacuuming with soft brush or compressed air. In case of heavy soiling: cleaning detergent, without grinding effects, in warm water, maximum 55 degrees Celcius. Wash with a soft, clean cloth (without microfibers) in plenty of water. Rins with lukewarm water. Drying: Self-drying in room temperature or wipe off with a slightly damp cleaning cloth (without microfibers).
Terms of use and maintenance
Before luminaire is turned on, it should be mounted according with this mounting instruction or any other applicable regulations.

Mounting instructions

Mounting of luminaire must be performed by a qualified person according with following instructions:

  • The warranty of luminaire does not apply, if the mounting of luminaire has been performed in precipitation (rain, snow, hail).
  • The warranty of luminaire does not apply, if a control system unauthorized by VIZULO or an inapplicable LED driver has been used to drive the luminaire.
  • The warranty of luminaire does not apply, if it has been used in an unsuitable ambient temperature or has been supplied by voltage outside of the specified range.
  • The warranty of luminaire does not apply, if the LED driver program has been changed in any way.
  • The warranty of the luminaire does not apply, if the logged history data of the LED driver has been deleted without the permission of VIZULO.
  • The warranty of luminaire does not apply, if it has been mounted in unspecified angles or upside down (luminaire glass directed up), or it has been completely submerged under water.

Safety instructions

Any actions with the luminaire must be performed by a qualified person, who is certified according with national regulations and requirements.
To prevent any accidents person installing the luminaire must follow national safety requirements and following instructions:

  • The label containing technical parameters of the luminaire has to be studied before the work on it has begun.
  • Any luminaire build or design changes are prohibited.
  • The luminaire must be used in good technical condition and according with this instruction.
  • Only VIZULO authorized spare parts and accessories can be used to repair the luminaire.
  • The repair of luminaire has to be performed by a qualified and certified person.

Maintenance and repair

Luminaire has to be disconnected from electrical grid before it is opened and/or repaired!

  • The person working with the luminaire must follow national regulations and legislations that apply to maintenance and testing of electrical or electronic appliances.
  • The luminaire may need to be cleaned depending on its environment. Only a damp cloth or a sponge may be used to clean the luminaire. Use only household detergents diluted by water.
  • Only VIZULO authorized spare parts may be used for the luminaire.
  • Instruction for changing spare parts must be requested from VIZULO and studied before the repair is attempted.
  • LED modules, lens and LED drivers can be changed on an installed luminaire, but it is advised to perform this task indoor to avoid water entering the luminaire.
  • Spare parts (lens, LED modules and drivers) should be ordered from the information available on the luminaire label.

VIZULO logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals