Dawlance DWT 1775 PL Fully Automatic Washing Machine User Manual

DWT 1775 PL Fully Automatic Washing Machine
User Manual

DWT 1775 PL Fully Automatic Washing Machine

FULLY AUTOMATIC WASHING MACHINE
User Manual DWT 1775 PL
Before operating this unit, please read this manual thoroughly, and retain for future reference.

Specifications

Parts name

Accessories

 |
---|---
Bottom cover (1po)| Wat inlet hos (1pC/
Watr inlet hose connector (1pc)

Symbol definition

Warning symbols| Pay special attention to the warning symbols. There may be serious risks to personal body safety or damages to the washing machine if not followed
---|---
Forbidden symbols| Please do not fidget or alter contents with this symbol, otherwise it  may result in appliance or personal body damage

Cautions

(Please risen the plug into the power socket with rated voltage 220VAC.| Always unplug the applenee and turnoff the water when the power is cut, moving or cleaning the washing machine. ce it is not r use. Do not -.sent Of pull off the plug with wet hand.
---|---
Do not make the deetnc cable bawled, stretched, twisted, strapped a changed, pressed or nipped. ll the electric cable a plug ks damaged or the socket becomes loose. they must be repaired a changed by our appointed repair stations or the professionals Of our post-sale servo° department to amid danger. The pin of the plug must remain dean. Please clean it carefully with a dry cloth if Ms dirty.
Oat t install the washing machine in bathroom or damp places. Do not wash the machine with water. do not put wet clothes on the control panel him.| Co not use water hotter than 50 C.
It the machine Is situated on a carpeted floor, please adjust the feet h coder to albw air to circulate freely.| Do not wash raincoat, bike cater. feather dress and such waterproof lewdest which will make the washing machine abnormal vibrations ckring spinning.
Do not share the same socket with other electric appliances. Do not use the damaged plug a loose socket.
Do not put hands into the working machine. It is dangerous even if the speed is very slow. Take special care of the children, and forbid them to climb on the washing machine.| It is dangerous to alter the specifications or attempt to modify this product in any way.
Do not overload the appliance or put any hot goods (such as the kettle with hot water) on the washing machine.| Garments which have been in contact with volatile petroleum products should not be machine washed.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.| Keep the appliance away from direct sunlight and heat sources like heater.
• Before washing, please ensure the tap is open and the inlet hose is installed properly.
• It is suggested to use low-foam washing powder.

Installation and adjustment

Please install and adjust the machine according to the requirements of the manual. It is very important to your safety and correct operation.

Unpacking

• Unpack the carton and take out the bottom panel.
• Open the top lid of washing machine and take out all of the accessories.
• Remove all wrappers, including the polystyrene base. You are advised to keep all the packaging for reuse in case the machine is to be transported again.

Installing the bottom cover

• Let the back of washing machine incline forward, make the side of bottom cover with sticker description back to washing machine, insert to the bottom of washing machine along the direction of arrow.

• Remove two fixing clamp by scissors, insert to the accordingly holes red lines indicating (gently pull fixing clamp should not be pulled out), make the bottom cover fixed on the base.

Positioning
The distance between the washing machine and the wall should be more than 50mm, and the maximum allowed angle of the shank base of the machine is 1°. The slanting or rough ground may cause operating stopped or unstable, please adjust it with the following methods:

• Horizontal checking observe the water bubble in balancing apparatus is in red circle or not. In red circle, it is horizontal
• Adjust the adjustable foot

1. Lift up the adjustable foot gently, loose the adjustable nut and twist the adjustable foot.

2. Fasten the nut after adjustment.

3. set the machine flat, and observe again. If the water bubble is not in red cirde, repeat the above procedure, till the water bubble is in red circle.

How to use drainpipe

1. The drainpipe must be hanged during use, the height is not more than 1.2m to avoid leakage or stop, if drain a long time, the machine will stop running.
2. You can adjust the situation of the elbow bend pipe to change the height of the drainpipe.
3. Do not extrude the drainpipe to ensue drain smoothly.

Water inlet installation

Cautions: When install the washing machine, please use the new hose assy along with the washing machine, old hose assy cannot be reused.
Tap selection
The front end should be longer than 10mm.
The tap exit end face should be flat and smooth, if not, file it to avoid leakage.
Check the connection between inlet hose connector and the tap

1. Swing the inlet hose gently to confirm If it is fastened.

2. After installation, open the tap and check if it leaks.
   

3. Do not bend the inlet hose with overstrain.

4. Before each usage, check the connection between inlet hose connector and the tap. Make sure they are finny fitted to prevent dropping from improper installation position

Connect the inlet hose with the washing machine

1. Do not take off the water absorption cushion. Please check if the cushion is dropped or damaged before each usage. If it is, contact the seller immediately.
2. Put the inlet hose nut on the inlet valve connector.
3. Fasten the inlet hose nut and swing It gently to make sure if it is suitable.
   

Operation

Preparation before operation
Preparation before washing

1. Connect the inlet hose and open the tap.
2. This appliance must be earthed. Confirm the socket is earthed reliably and insert the power plug. The earth terminal should not link to gas pipeline, tap pipeline etc.
3. Hang up the drainpipe.

Warning: The temperature of the water should be less than 50°C
Before washing the laundries, please pay attention to the followings:
Read laundrycare label and check if there Is special requirements for the laundries.
Before washing, empty all pockets of small objects which may have been left inside (coins, keys, screws etc.) Knot the long band, fasten the buttons and close the zippers.
Do not overload the machine. Load the laundry loosely acerating large items with small ones.
Sat the laundry according to the type of fabric, color-fastness and how dirty it is. Put thin laundries. woolens and such prone to wear and tear laundries Into washing beg.

A. Make sure the laundries are washable.
B. It is essential to wash new colored items separately when washing for the first time. White items should not be washed with colored items.
C. Please Immerge the non-absorbable laundries by hand.
D. Some stains such as fruit, wine. grass. rust etc. are difficult to remove and should be treated before washing with specific products, which can be found in most household shops. In some cases, it may help to soak the stain before washing with a special pre-soak product or biological detergent.
E. Overturn the nap fabric and long floss laundries before putting them Into the machine.
F. Do not put the laundries polluted by chemicals Into the machine directly.
G. Very small item (handkerchiefs, ribbons. socks etc.) should be washed in a washing bag or a pillow case.

Load laundries

• The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition. Washing quantity shall be lower than the rated capacity. The maximum capacity of this machine is 15.0kg.

• Different thickness, size and type of the laundries will influence the actual washing capacity. It is suitable that the laundries can be turned round normally during washing.

• Do not select high water level when laundries are less than 1.5kg to avoid water splashing.

Use of detergent

• Withdraw the dispenser box before adding detergent
• Pour concentrated synthetic washing powder into the box directly as shown in the left illustration.
• For the quantity of the concentrated washing powder, please refer to Its manual.
• It is suggested to use low suds washing powder.

How to use bleach

• Fill water to the selected level, dilute the bleach in the container, and pour it slowly into the washing tub
• Do not use bleach for colored or figured laundries as they are prone to lose colors
• Do not put bleach to laundries directly.
• Refer to the manual for the usage and quantity of the bleach.
• Please dissolve powder bleach before use.

How to use the washing powder

• Dissolve in the machine directly <not suitable for preset program) 1. Low water level. 2. Add the washing powder, and run for 30 seconds to dissolve it completely. 3. Put laundries in, select suitable water level.

• The instant dissolving of the washing powder
  1. Prepare warm water of are in a container.
  2. Pour the powder while stirring to fully dissolve it.

• The washing powder is more prone to pollute the laundries than the detergent, therefore, please use it with proper quantity.

• Washing powder with poor quality or not used for a long period may get blocked, please clean the detergent box in time.

• It is suggested to use low foam washing powder.

• For the quantity of the concentrated washing powder. please refer to its manual.

• Remarks: Avoid splashing of water and waste of washing powder, water level should not be too high if laundries are too small.

Control panel instructions

Operation steps

1. Press power switch, put through power, the machine is in state of beginning:
2. If there is no water in inner tub, washing machine is in state of ‘FUZZY’, the state details as per each model’s button explanation. Now press ‘START/PAUSE” button (press “PROGRAM” and select ‘STRONG”, the washing machine is in state of ‘FUZZY”), the washing machine will start fuzzy sensor and to sensor the weight of laundries and set water level automatically.
3. If there is water in inner tub, washing machine is not in state of ‘FUZZY’, the state details as per each model’s button explanation. Now press “PROGRAM’ and “PROCESS” to select proper program and process.
4. Press “program” button to select proper program.
5. Press “process” button to begin process selection.

Times of pressing the “process” button| Selected procedure Program| Applicable procedure| Contents (the lighted indicator indicate the programs about to run)
---|---|---|---
0| Wash, rinse, spin| Standard program| Wash rinse and spin lights are on
1| Spin| Wash by hand and only need tospin| Spin light is on
2| Soak, wash, rinse, spin| For dirty laundries| Soak, wash, rinse and spin lights are on
3| Wash| when use detergent repeatedly| Wash light is on
4| Wash, rinse| No need tospin for laundries creased easily| Wash and rinse lights are on
5| Rinse, spin| Wash by hand and need to rinseand rinse| Rinse and spin lights are on

Remarks: Press PROCESS button continually, the above mode will be cycled in turn.
4. Select appropriate water level according to your laundries quantity.
5. At the beginning of start, if need to select preset, please press PRESET button and select appropriate preset time, the preset time is shown in the digital timer, and the time indicates the time to finish the whole washing. If want to cancel PRESET, please press POWER to make the washing machine in waiting state.
6. At the beginning of start, if need to select air-dry, press PROGRAM button and select AIR DRY program, press PRESET can select the time of AIR DRY. When the air dry function is over, the washing machine will be in waiting state.
7. Close the top lid, press START/PAUSE, the washing machine is working. During working, press WATER LEVEL and PRESET button, child lock function will start, press again, unlock this function. If open the top lid, washing machine will stop working and will give an alarm. 8. When the washing is finished, buzzer alarm, power supply will cut off automatically.

Maintenance

Maintenance methods
After the end of the programmed

• The machine stops automatically, and music buzzer will remind you to take out the laundries or start again
• Once you have finished using the machine, you are advised to unplug it and turn off the water taps to avoid unexpected leak or fire.

External cleaning
Clean the exterior cabinet of the appliance with soft cloth. Do not use cleanser, volatile chemical materials to clean the machine, which will damage plastic parts and the surface.
Magic filter cleaning

1. Pull out magic fitter
2. Open the box and clean it
3. Close it and reinstall it
4. Check if the lint block part is in good condition
   

Clean inlet gate
It Is possible that the inlet filter net can be blocked by the dust, please clean it according to the follow steps:

1. Close the tap and turn on the power switch.

2. Start the washing machine for 5 seconds (make the water in the inlet hose flows to the tub), and cut off the power supply.

3. Pull off the inlet hose, remove and clean the inlet valve and the inlet net, and install again.

4. Once you have using the machine, you are advised to turn off the water taps. (If necessary, pull out the inlet hose).

5. Do not keep water in tub for a long time. When washing is finished, drain it right away.

6. Once you have finished using the machine, you are advised to unplug it.

7. Put the electric cable and the drain hose in order.

8. Wipe the water on the surface and in tub with soft cloth and keep the top lid opening for a while. It helps to prevent moulid and stagnant smells forming inside the appliance.

If the water in the inner tub has possibility to freeze, please do like below:

1. In winter, if remaining water freeze can cause the washing machine trouble, please take off the water inlet hose and drain out the water in the hose and inner tub.
2. If the water freeze, please don’t operate the washing machine. Put 40’C hot water in the tub, the hot water should submerge the pulsator, after a few minutes, rotate the pulsator by hand gently, then you can operate the washing machine.

Troubleshooting

Before contacting the technicians, please make the following checks:

in the socket
Power switch is not turned on Power supply is cut off| Insert the plug tightly
Check the socket or change to another socket Press power switch
Check power supply
Inlet hose leaks| Inlet hose connector (connecting with the tap) is not fixed tightly Inlet hose and washing machine connector are loose| Install the inlet hose again
Tighten the connector of the machine
It does not drain| Water outlet of drainpipe is higher than 1.2m Drainpipe is bended or get blocked| The height of the drainpipe should be less than 1.2m Straighten or clean the drainpipe
It does not inlet| No water supply
Tap is not open
Inlet hose is blocked| Restart when water supply is resumed
Open the tap
Clean the filter according to before “clean inlet gate”
Spin stops and begins to inlet during spin program| Laundries are too much or too little Machine is not placed stably| The machine is adjusting automatically
Press the program button to select SPIN, but It does not spin| Do not close the top lid when drain is finished Open up the top lid when start drain| Close the toplid Close the top lid
The spin is intermittent when spin starts| Balance the laundries to reach to the best spin effect| Normal
First time to use, some water flows from the drainpipe| The remaining water when the factory makes test| Normal

Notes : If there is still a fault after the above checks, please pull out the plug and contact the seller right away. It is dangerous to repair this product by yourself.

Other functions

1. Give an alarm

up the alarm
El| After draining 7 minutes, it still does not reach to water level| Open the lid, check your drain assembly for any possibility of drain choking. To stop the alarm, close the lid again and press play
E2| The top lid is open when spinning| Close the top lid and clear up the alarm
E3| Spin does not balance| Open the top lid, make the laundries place equally, then close it and clear up the alarm
E4| After inlet 40 minutes still not reach to setting water level| Open the lid, check the water inlet circuit. To stop the alarm, close the lid again and press play
E5 Child-lock light
flashing continuously| The top lid is opened after setting child-lock| Close the top lid and clear up the alarm
Fl| Water level sensor is wrong| Cut the power supply and call the technicians

2. Imbalance adjustment
During spinning, if the laundries are not placed equally in the tub, it would cause violent vibration. This machine has imbalance adjustment function, and the vibration testing system will supervise the running. Once vibration is beyond certain level, the adjustment system will start automatically to adjust the imbalance.
3. Power supply is cut off automatically

1. Press the power supply button and does not start the program in 10 minutes, the power supply will be cut off automatically.
2. After the washing is finished, buzzer will remind, the power supply can be cut off automatically.

4. Child lock function

1. If set child lock function, all the buttons will be locked including POWER. If the top lid is opened during the washing machine is working, the washing will be stopped and an alarm will buzz. But if you can close the top lid in 5 seconds, the washing machine will stop alarm and continue working. If can not close the top lid in 5 seconds, the washing machine will begin draining if there is water in the inner tub, even closing the top lid is not valid. During the draining, alarm will be given every 10 seconds, when the water in the inner tub is about 5cm higher, alarm will be given every 10 minutes (alarm is always given). When the draining is finished, the washing machine will be in the state of waiting, if close the top lid, the washing machine will be unlocked and will start working as previous setting.
2. Once child lock is set, if open top lid over 5 seconds during washing or rinse (there is water in the inner tub), washing machine will drain and give an alram.
   If you unlock the function during draining, the washing machine will add water to setting water level and will continue working.

5. Water recycle function
If set water recycle function, after the last time rinse finished, the washing machine will not drain and spin, SPIN and WATER RECYCLE indicator light are flashing and an alarm is given, the washing machine stop working (if nobody operates, the alarm will be given every 10 minutes, in 1 hour, power supply will be cut off automatically). When press START/PAUSE, WATER RECYCLE indicator light will turn on and the washing machine will begin to drain and spin, the user can reuse the water

UAN #021-111-11-7359 (RELY)
Head Office: Dawlance Center 7/4, Civil Lines-9
Dr. Ziauddin Ahmed Road, Karachi.
Ph: (021)35652450-9
E-mail: customer.service@dawlance.com.pk
Website: UAN #021-111-11-7359 (RELY)
Head Office: Dawlance Center 7/4, Civil Lines-9
Dr. Ziauddin Ahmed Road, Karachi.
Ph: (021)35652450-9
E-mail: customer.service@dawlance.com.pk
Website: www.dawlance.com.pk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>