WELLFOR DK-MCA2330-BL Medicine Cabinet Instruction Manual

Medicine Cabinet
Instruction Manual

READ THE INSTRUCTIONS CAREFULLY, and familiarize yourself with all the parts as shown in the exploded view. The exploded view will also provide a helpful reference when relating to the location of the various parts and how they are mounted.

20″ Height series=2 shelf kits+ 0 decorative cover
24″ Height series=2 shelf kits+ 4 decorative cover
26″ Height series=2 shelf kits+ 6 decorative cover 30″
Height series=3 shelf kits+ 4 decorative cover 36″
Height series=3 shelf kits+ 8 decorative cover

PARTS LIST.

WARNING: Safety glasses should always be worn when working with a medicine cabinet
RECOMMENDED TOOLS

Determining Measurement and Direction:

If needed, please turn over the upside to the downside, you may get the opposite hand installations.

Recessed or semi-recessed

1. Pull off the side kits from the cabinet as the figure shown.
2. Make sure hinges are on the correct side of the opening for left-hand or right-hand operation. Place the cabinet box into the rough opening. On fully recessed applications, make sure the cabinet flange covers the rough opening evenly all around (Fig 3). In semi-recess applications, mirror edges should meet the wall surface. (Fig 4). Shim as needed.
3. Insert four (4) #10 x 11/2″ screws into four locations provided for recessed installation (Fig 5). Be careful not to overtighten. Make sure the cabinet is centered in a rough opening. Cover screws with provided caps 10

How to Surface Mount Cabinet

If installing in combination with a middle mirror/shelf kit, please see the “Center Mirror/Shelf Kit Installation” Directions that came with your center mirror prior to performing the steps below

1. Establish precise height and draw a level horizontal line (Fig 6). IMPORTANT: Detect the medicine cabinet at a precise height. Make sure there is at least 1″ of clearance above any obstructions.
2. Place the bottom of the wall bracket on the horizontal line and at the correct position left to right and mark holes on the wall (Fig 7).
3. Drill 8 mm hole if required for wall anchor and place wall anchor in hole. Mount wall bracket with #10 x 11/2″ e screws. (Fig 8)
4. Insert surface mount z-clips as shown (Fig 9 & 10).
5. Place cabinet into wall bracket (Fig 11). Mark hole locations of z-clips (Fig 12). When determining location, it is recommended that at least one z-clip be located at a stud. Detach cabinet and drill 8mm hole if needed for anchor, and place in anchor in hole.
6. Remount cabinet and connect with #10 x 1 112″ 6 screws (Fig 13). Be careful not to damage or scrape the top flange

Door Installation

1. Remove protective packaging from the door, and be careful not to bump the edges of the mirror. Line hinges up against hinge mounting plates. Snap into position (Fig 14).
2. The door should “snap” locked when about 1″ from being fully closed. The door should be placed even in relation to the cabinet.

Limit Clips

Limit Clips 14 are provided should you need to reduce the opening swing of the cabinet door from 170 degrees to 130 degrees (see top view) This will eliminate the possibility of the door hitting a wall sconce or other decorative items.

Additional Item Installation

1. Insert dear shelf clip 0 into the appropriate hole location using 2 clips per shelf (Fig 16).
2. Place glass shelf® on top of dear shelf clips making sure the shelf is against the back of the cabinet. Press lightly to adhere to the shelf clip sticker (Fig 17).
3. Fill remaining holes with hole plugs® (Fig 18). Fill the rest of the shelf dip holes with decorative covers 0 (Fig 19).

COVER PLATE(2pcs)

Pasting Nameplate

1. After the door and cabinet are installed, install name plates by peeling protective plastic from the door and back of the nameplate, then placing the nameplate in the proper location (Fig 26)
   

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>