Johan Lewis House Jamie Ceiling pendant User Manual
- June 7, 2024
- JOHAN LEWIS
Table of Contents
User manual
House Jamie
Ceiling pendant
Thank you for purchasing this House Jamie ceiling pendant. Please read the instructions carefully before use to ensure safe and satisfactory operations of this product. Please keep this instruction for future reference.
Warnings!
For your safety, this product must be installed in accordance with local
Building Regulations. If in any doubt, or where required by the law, consult a
competent person who is registered with an electrical self-certification
scheme. Further information is available online or by phone your Local
Authority. To prevent electric shock, switch off the mains supply before
installing or maintaining this product. Ensure other persons cannot restore
the electricity supply without your knowledge. Always use the correct bulb
type with the correct wattage as indicated in the specification table. This
product is Class I = and should be fitted to a lighting Supply (with earth)
protected by a 5 amp fuse or equivalent circuit breaker. When changing the
bulb, always switch off at the mains and allow the old bulb to cool down
before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish. Replace bulbs from John Lewis or established brands of the same type and compatibility.
Parts list
Assembly
Never install your appliance on a wet, freshly painted or plastered surface. Ensure the house electricity supply is switched off at the fuse box. If removing an existing fitting, note down all wiring connections. Check the fixings will not touch any existing wiring before drilling and attaching the light to the ceiling. Ensure you thread the wall wires through the black insulating tube fixed to the appliance.
Step 1
Remove mounting bracket from the fitting by removing the retaining screws and
washers, retain for later. Using the mounting bracket as a template, mark and
then drill the fixing holes in the ceiling (ensure the screws are firmly fixed
into a solid or other suitable mounting and not just the plasterboard.). Take
care not to damage wiring. Attach the mounting bracket to the mounting surface
using suitable fixings. Do not attach the fitting to the mounting bracket at
this stage. Make sure no wires are trapped in the process.
Step 2
Ensuring that the power has been isolated, connect the electrical supply wires
to the connector blocks corresponding terminals. Wrap the terminal block in
two layers of insulating tape. Make the electrical connections as follows:
- Connect the supply live (normally brown or red) to fitting life (embossed “L”) on the terminal block housing.
- Connect the supply neutral (normally blue or black) to fitting neutral (embossed “N”) on the terminal block housing.
- Connect the supply earth (normally green/yellow or unsheathed) to earth (embossed “ ”) on terminal block housing.
Ensure electrical connections are tight and no loose strands of wire protrude
from the terminal block then close the connector block cover by snapping back
together.
Please note that residential wiring can vary, if you are unsure about the
correct polarity please consult a qualified electrician.
Height Adjustment: This fitting is height adjustable at the point of installation only. No attempt must be made to adjust the height once it has been attached to the ceiling. If adjustment is required at a later date the fitting must be isolated from the mains and removed from the ceiling first. Lay the fitting on a clear covered surface. Using a suitably sized flat-bladed screwdriver loosen the plastic screw clamp under the ceiling cup, also undo the screws or clamp located in the ceiling cup. Carefully pull the cable through the ceiling cup to the desired height and then retighten all screws to ensure that clamps are fully secured.
Step 3
Excess cable must be carefully located inside the ceiling cup or within the
ceiling void. Carefully offer fitting over mounting bracket then secure in
place with the screws and washers removed earlier.
Fit shade: Remove the shade ring from the lamp holder, fit the shade top
cap cover over the lamp holder then, the shade, and replace the shade ring to
secure it in place. Take care not to overtighten as this may cause damage to
the fitting.
Fit the bulb, type, and wattage as indicated on the fitting (bulb not
supplied). The wattage indicated must not be exceeded. Once installation is
complete, the house electricity can be restored at the fuse box.
Recommended bulb
1 x 3-6 Watt ES energy efficient LED
or
1 x 28 Watt ES eco halogen
Bulb not included
Specification
Max power: 28W
Voltage: 220~240V, 50/60Hz
IP20
Weight 0.7Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal household waste and should be recycled. John Lewis does not operate in-store take back, but as a member of the Distributor, the Take-Back scheme has funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please e-mail lightingparts@JLPspares.co.uk?
Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off the light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 04 07/18
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>