AYR 762 WiFi Digital Door Viewer User Manual

WIFI DIGITAL DOOR VIEWER
USER MANUAL

762

http://gofile.me/4bi9Q/6pjoWC2PL

Product Outline

1. LCD display
2. Reset key
3. Battery charging port
4. TF Card slot
5. Left key(Restore factory settings key)
6. Middle key(Monitor key/ power key)
7. Right key (Network configuration key)
8. PIR sensor
9. IR LED
10. Doorbell key
11. Camera
12. Speaker
13. Micro phone

Key Function Description

Left key (Restore factory settings key): When the screen is on, long press this key for 10 seconds, the device will return to the factory settings.
Middle key (Monitor key/ power key): Long press this key for 3 seconds to turn on / off the device, click this key to turn on / off the screen.
Right key (Network configuration key): in the power on state, long press this key for 5 seconds to enter the network configuration mode, and long press this key again for 5 seconds to exit the network configuration mode.
Doorbell key: press this key to wake up the doorbell host, ring and call the connected mobile phone.

How to install the device on the door

Step 1: According to the thickness of the door to select a suitable bolt, then, screw the boltinto the hole (refer installation icon 1)
Step2: Tear off double-side adhesive protective film on the back of the outdoor part, insertthe unit barrel together with the FPC cable through the peephole of the door, then
stick the outdoor part on door(motion detection is upward, doorbell key is downward)
Step3: Take out the metal bracket (the “UP” arrow on the bracket means upward), pass the FPC cable through the rectangular hole, the right screw through the round of the metal bracket, then lock the metal bracket with the outdoor unit tightly.

Step4: Insert the microSD card (not included) into the indoor unit if using one.
Step5: Connect the FPC cable from outdoor part to the connector of the indoor part (pay attention to the right direction)
Step6: The four slots on the back of indoor part is aligned with four projection on metal bracket and buckle up, then pull down the outdoor part to lock tightly.

App Download and Installation

1. Scan the QR code in the picture below and download “Tuya smart” with your mobile phone. Or search for “TUYA Smart” in Apple store or Google store, then download it.
2. Accept all permisions required by the APP.

https://smartapp.tuya.com/tuyasmart

Account Registration / Login

New users need to register a new account, and then log in with a user name and password

Device addition and network configuration

1. This device can only work with a 2.4GHz Wi-Fi signal. So please check your router and make sure it works at 2.4GHz. When setting up the network, please keep the product and mobile phone as close as possible to the wireless router to ensure a good network signal.
2. Please perform the following steps 1-4 in strict order.
3. In the process of network configuration, if you hear the host message “configure network timeout” or the interface shows that the network configuration fails, please exit
   the application and restart the product, and then operate again from step 1.

Step 1: Open and log in the application, click “add device” and select “Video Surveillance” in the product catalogue on the left, as shown in (figure 1). Then select “Smart doorbell” in the product type on the right, and the interface will appear as shown in (figure 2).

Step 2: Remove the outdoor unit and indoor unit from the device (host), and connect the cable from the outdoor unit to the back of the host, as shown in (figure 3). Press and hold down the (centre key) on the device for 3 seconds to start up. Then long press the (right key) for 5 seconds to enter the network configuration mode, at this time, the host will have a voice prompt “please use app to setup the network”, and you will see the blue indicator blinking (blinking once in 1 second) on the host.

Step 3: When you hear the voice message from “please use app to setup the network” and see the blue indicator flashes (flashes once in 1 second), please select the reminder “make sure the indicator flashes quickly or a warning tone is heard” in the mobile APP (figure 2), and then click “next”, a new interface will appear (figure 5).
Step 4: Enter the Wi-Fi username and password (figure 5). Then click “Next” to bring up the QR code interface (Figure 6). At this time, point the camera lens at the QR code. When the host sends a voice message “Connecting network”, click “next” to display the QR code interface (figure 6), click the “Hear the warning tone” option in the interface (figure 6), and the “adding device” interface (figure 7) appears. After about 30 seconds, when the host sends the voice message “network setup successfully”, the network setup is finished, and the interface of (figure 8) appears. Click “Finished” and then click “Security camera” to enter the video interface.

Device Settings and App Settings

Device settings: when the mobile phone and the device are connected, the device can be set online.
Setting method: click the “pencil” symbol in the upper right corner of the video window, then the device setting interface pops up, as shown in (figure 9).

Note: when the phone is disconnected from the device, the device cannot be set.

Device Parameter

Support OS: Android and iOS
Camera Pixel: 720P
LCD Screen: 4.3Inch ,IPS, 480*272
Battery capacity: 3500mAh
Two way Audio: support
Motion detection: support
External storage: Micro SD card 128GB maximum (not included)
IR LED wave length: 940nm (invisible light)
Battery Charger: 5V / 2A
Suitable for door hole: diameter 14-35mm
Applicable door thickness range: 35-100mmWireless
WIFI: ieee802.11b/g/n 2.4GHz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>