AYR 754 Digital Door Viewer User Manual
- June 10, 2024
- AYR
Table of Contents
AYR 754 Digital Door Viewer
Product Information
The Digital Door Viewer 754 is a device that allows you to view who is at your door without opening it. This user manual provides instructions on how to use the product effectively.
Package Contents
- 1 LCD Screen
- 1 Fixing Screw
- 4 AAA Batteries
- 1 Holding Plate
- 1 Washer
- 1 Camera
- 3 Locking Barrel
- 1 Tightening Tool
Product Specifications
- Power: 4 AAA batteries
- Screen: 2.4″ TFT LCD
- Viewing Angle: 100 degrees
- Door Thickness: 35-110mm
- Size: 60x103x14mm
Product Usage Instruction
Installation Instructions
- Replace the existing door viewer or drill a 14mm hole in the door at the required height.
- Peel off the 3M sticker top layer and then insert the camera from the outside. Ensure the doorbell button is under the camera and adjust the camera vertically to the ground (FIG.1). Warning: It is very important to peel off the label so that the camera is perfectly attached to the door (FIG. 1).
- Peel off the 3M sticker top layer on the holding plate and fit the holding plate over the end of the camera wires onto the back of the door. Make sure the arrow on the holding plate points upwards. Then screw up the locking barrel on to the back of the camera. This will hold the plate to the door (FIG.2).
Installation and Replacement of Batteries
Do not put the batteries until the peephole is fully installed at the door.
To install or replace batteries:
- Unscrew the retainer plate from the bottom of the visor and remove the adhesive protector.
- Insert 4 AAA batteries into the battery compartment.
Operation
The cable of data must be completely connected at the back of the screen, and
directed towards the bottom. The excess cable must be placed carefully in the
housing of the back of the viewer (FIG.3).
Warnings
- Please READ THIS USER MANUAL CAREFULLY before using the product.
- CONSERVEZ et utilisez ce manuel.
- To avoid damage to the product or injury to the user, never attempt to repair or change the product or its accessories by yourself.
- BATTERIES: Any abandoned batteries should be disposed of according to local environmental protection rules and regulations.
- DO NOT cut the battery casing with a blade to avoid damaging the batteries.
- Make sure you assemble the doorbell camera carefully. If the camera wire is pulled or folded, this could damage the product.
- When fitting the door viewer camera, first unscrew the camera barrel and insert the door viewer camera into the peephole with the arrow points up. After the camera is well positioned, screw up the locking barrel from inside door.
- DO NOT rotate the camera from outside door, this could damage the camera. Also, DO NOT rotate the camera when disassembling this product.
WARNING
Make sure you assemble the doorbell camera carefully.
IF THE CAMERA WIRE IS PULLED OR FOLDED,
this could damage the product.
When fitting the door viewer camera, fisrt unscrew the camera barrel and insert the door viewer camera into the peephole with the arrow points up. After the camera is well positioned, screw up the locking barrel from inside door.
DO NOT rotate the camera from out side door, this could damage the camera. Also DO NOT rotate camera when disassembling this product.
WARNING:
- Please READ THIS USER MANUAL CAREFULLY before using the product.
- CONSERVEZ et utilisez ce manuel.
- TO AVOID DAMAGE to the product or injury to the user, never attempt to repair or change the product or its accessories by yourself.
- BATTERIES: Any abandoned batteries should be disposed according to local environment protection rules and regulations.
- DO NOT cut the battery casing with a blade to avoid damaging the batteries.
Before install
Before installation, unscrew the retainer plate from the bottom of the visor
and remove the adhesive protector.
Make sure that the thickness of the door where the peephole will be ins-talled is appropriate. Please note that for some doors the thickness in the center may be diffe-rent than other parts.
Package list
- 1 LCD Screen
- 1 fixing screw
- 4 x AAA batteries
- 1 Holding plate
- 1 Washer
- 1 Camera
- 3 Locking barrel
- 1 Tightening tool
Installation instructions
-
Replace the existing door viewer or drill a 14mm hole in the door at the required height. Peel off the 3M sticker top layer and then insert the camera from the outside. Ensure the doorbell button is under the camera and adjust the camera vertically to the ground(FIG.1)
Warning: It is very important to peel off the label so that the camera is perfectly attached to the door(FIG. 1). -
Peel off the 3M sticker top layer on the holding plate and fit the holding plate over the end of the camera wires on to the back of the door. Make sure the arrow on the holding plate points upwards. Then screw up the locking barrel on to the back of the camera. This will hold the plate to the door(FIG.2)
-
When inserting the camera wire into the socket, ensure you match the connectors correctly. (FIG. 3) . The excessive wire should be gently placed into the groove at the back of the screen.
Warning: it is very important that the connector is perfectly connected and in the position indicated. -
Hook the screen over the bracket at the top of the holding plate and secure with one small screw through the hole at the bottom of the screen. (FIG. 4).
Batteries Replacement And Installation
- Slide the lid upwards to open, as shown in the diagram.
- Put in the batteries according to the “+” “-” sign on the lid.
- Take the reverse steps to close the lid.
Operation
- Power button: press and release the button. You will be able to see the image for 10 seconds.
- Indicator light: If the indicator lights up, replace the batteries.
Specifications
- Model: 754
- Door thickness: 38 à 110 mm
- Door barrel diameter: 14 à 22 mm
- Camera: 0,3 mégapixel CMOS
- LCD Screen: 4 ”TFT
- Power: 4 piles AAA
- Size: 139 (largeur) x77 (hauteur) x15,8 (profondeur) mm.
- Weight: 140g
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>