AYR OPENING DOORS 758 Digital Door Viewer With Alarm User Manual

User Manual DIGITAL DOOR VIEWER with ALARM
758

758 Digital Door Viewer With Alarm

http://gofile.me/4bi9Q/XyNuPiy3b

WARNING!
DO NOT PUT THE BATTERIES until the peephole is fully installed at the door WARNING!
Make sure you assemble the doorbell camera carefully.
IF THE CAMERA WIRE IS PULLED OR FOLDED, this could damage the product.
Correct assembly
When fitting the door bell camera, first unscrew the camera barrel and then peel off the 3M sticker from the back of the camera (Fig. 1).
Stick the camera to the outside of the door making sure the door bell is at the bottom (Fig. 2). Incorrect assembly
DO NOT fit the door bell camera without sticking to the door using the 3M sticker. This would cause the door bell to rotate and will damage the cables and may cause the unit to fail (Fig. 3).

WARNING:

1. Please READ THIS USER MANUAL CAREFULLY before using the product.
2. CONSERVEZ et utilisez ce manuel.
3. TO AVOID DAMAGE to the product or injury to the user, never attempt to repair or change the product or its accessories by yourself.
4. BATTERIES: Any abandoned batteries should be disposed according to local environment protection rules and regulations.
5. ANY ACCIDENTAL FACTOR such as being struck by lightning or any incorrect operation could cause a memory loss on the SD card. Keeping copies of the videos is strongly recommended in case of memory loss. We are not res- ponsible for any loss of data.mations.

Before install:
Before installation, unscrew the retainer plate from the bottom of the visor and remove the adhesive protector.
Make sure that the thickness of the door where the peephole will be installed is appropriate.
Please note that for some doors the thickness in the center may be different than other parts.

Package list:

1. 1 LCD Screen
2. 1 ixing screw
3. 4 x AAA batteries
4. 1 Holding plate
5. 1 Camera
6. 3 Locking barrel
7. 1 Tightening tool

Installation instructions

1. Replace the existing door viewer or drill a 14mm hole in the door at the required height. Peel off the 3M sticker top layer and then insert the camera from the outside .
   Ensure the door bell button is under the camera and adjust the camera vertically to the ground(FIG.1)
   Warning: It is very important to peel off the label so that the camera is perfectly attached to the door(FIG. 1).

2. Peel off the 3M sticker top layer on the holding plate and fit the holding plate over the end of the camera wires on to the back of the door. Make sure the arrow on the holding plate points upwards. Then screw up the locking barrel on to the back of the camera.This will hold the plate to the door(FIG.2)

3. When inserting the camera wire into the socket ,ensure you match the connectors correctly.(FIG. 3) If inserted incorrectly, this can damage the camera cables. The excessive wire should be gently placed into the groove at the back of the screen.
   Warning: it is very important that the connector is perfectly connected and in the position indicated.

4. Hook the screen over the bracket at the top of the holding plate and secure with one small screw through the hole at the bottom of the screen.(FIG. 4).

Installation and replacement of batteries:

1. Slide the lid upwards to open, as shown in diagram.
2. Put in the batteries according to the “+” “-” sign on the lid.
3. Take the reverse steps to close the lid.

WARNING:

1. DO NOT force when opening and closing the lid to avoid lid damage.
2. DO NOT press the lid to the opposite direction when opening to avoid any lid damage.
3. When the low battery indicator is on, please replace all batteries to avoid any damage to this product by battery weeping.
4. Use AAA, LR03 1.5V alkaline battery.
5. WARNING! DO NOT use rechargeable batteries.

Button functions:

5 camera data wire connector
6 SD card socket

-After enters picture browse mode, press UP button to browse pictures backwards;
-In setting mode, press Up button to adjust the item you selected;
| | -In picture browse mode, press Down button to browse pictures onwards;
-In setting mode, press Down button to adjust the item you selected;
-In home page, press Down button to take picture.
| | -Press Menu button to enter menu page;
-When deleting pictures, press Menu button you can then choose to delete the current photo;
-In picture browse and setting mode, press and hold the menu button to exit the current page.
| | -After installing new batteries, press and hold power button to start.

Memory Card Installation

-Max. 8GB TF card can be used, over HDSC Class 6 is suggested
-Before inserting the TF card, make sure the metal cover above the TF card socket is pushed towards the OPEN mark.(OPEN)

• Lift and open the upper of the metal cover and insert TF card into the metal cover Then replace the metal cover and push back to LOCK mark (LOCK).
• If the card cannot be read, format it to FAT 32 from a computer.

Adjust settings

Selection of recorded images:

• The default store is local file. (Capacity = 26 photos)
• In the setting menu you can select where to save the images, in internal memory or on SD card (not included)
• To do this, select settings menu and tap below until you reach the disk icon, tap to select the peephole or card, and then press the button. until you exit the main screen.

System settings:

• Under normal mode, press to enter setting mode.
• Then you should see the below setting mode page.
• Press to find different settings.

Time–Date–Ringtone–Volume–Auto power-off time–Save file in

• Press to change the settings.
• In TIME/DATE setting, press will increase the current number; Holding the button down will accelerate the adjustment.
• After the setting is changed, the system will automatically save the result and exit the setting page in a few seconds.
• If you need to exit the setting page, press and hold

Instructions for use:
To observe outdoors:

• Under normal mode, you can observe outdoors once you press the power button .

Visitors:

• When visitors press the door bell, the bell will ring inside the room. The screen will automatically turn on showing the image of outside. It will automatically power off once the set time is reached.
• Under normal mode, press will take a picture of outdoors and save it automatically.
• Also as the door bell is pressed, the camera will automatically take a photo of the visitors and the photo will be stored in the set file in case the host is out, so as to check the visitors’ identity afterwards or to use the information for security purposes..

Replay and delete of the photos:

• Under normal mode, press to replay photos
• When you browse the photos, press or to choose photos
• When you check the photos, press button to choose to delete the current photo. After a short press on the button, you will see trash icon
• Press to confirm to delete.

Vibration alarm function

1. The vibration alarm function is shut by default at the factory. The vibration alarm function needs to be started by pressing the button for 3 seconds when display turns on.
2. The buzzer emits three beeps and a vibration alarm icon appears in the lower right corner of the display.
3. To shut the vibration alarm function needs to press the button for 3 seconds when the display turns on. The buzzer emits a long “drip” sound, the vibration alarm icon disappears, which indicates the vibration alarm function shuts.
4. When the vibration alarm function starts, once the Digital Door Viewer detects the vibration, it will trigger an alarm. After 10 seconds, the display automatically turns on, take a photo, emits a continuous alarm sound “Drip”, and a red alarm iconppears in the lower right corner of the display.
5. After 10 seconds the Digital Door Viewer stops the alarm, shuts down and continues keeping the vibration alarm monitoring state.
6. After the vibration alarm is triggered, the owner can cancel the alarm at any time by short pressing the power button of the display.en appuyant sur le bouton ON .

Quick guide:

Discover

on|
---|---

Alarm

Take photo

See photos

Delete photos

1. on| 2.scroll
|
3. select| 4. access
|
5. select| 6. confirm
|
Set options

1. on| 2.access
|
3. select| 4. access
|
5. select| 6. confirm
|

Specifications

Model: 7040M
Door thickness: 38~110mm
Door barrel diameter: 14-26mm
Camera: 0.3 Mega pixels
LCD Screen: 4.0”TFT
Resolution: QVGA (480×320)
Power: 4 AAA, LR03 1.5V alkaline battery
Local memory storage: Approx 26 photos (The amount could differ de- pending on the type of environment the camera is situated in exterior )
Card type: Micro SDcard (TF), max 8GB. NOT include TF card. This should be purchased by user separately.
Photo volume for 1GB: 2000pc (lab condition, the actual volume could differ under different circumstances)
Size: 139(w) 77(H) 15.8(D)mm
Weight: 185g
Alarm: 90 dB

www.ayr.es

Documents / Resources

| AYR OPENING DOORS 758 Digital Door Viewer With Alarm [pdf] User Manual
758, 758 Digital Door Viewer With Alarm, Digital Door Viewer With Alarm, Door Viewer With Alarm, Viewer With Alarm, Alarm
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>