nordlux Blokhus 2501 Wall Light Instruction Manual
- June 3, 2024
- nordlux
Table of Contents
Blokhus 2501 Wall Light
Mounting instruction
IP5X
IP5X: Dust is prevented from entering the lamp in amounts that
can cause damage to the function/safety of the lamp.
IPX4
IPX4: Raindrops falling from any angle will not affect the
function/safety of the lamp.
Class I: The lamp has an earth terminal and must be connected
to the yellow/green earth wire.
The lamp is only suitable for connecting directly to the mains.
IMPORTANT! Always shut off power to the circuit before starting
installation work. In some countries electrical installation work may only
be carried out by a authorized electrical contractor. Contact your local
electricity authority for advice.
Disposal of waste equipment by users in private households
in the European Union. This symbol indicates that this product must
not be disposed of with your other household waste. Electrical and
electronic equipment contain substances which may cause damage
to human health and environment if not recycled correctly. It is your
responsibility to hand over to a designated collection point for recycling
of waste electrical and electronic equipment. When handing over for
correct recycling you help to prevent these products straining nature
and environment unnecessarily and to protect human health. For more
information regarding correct disposal, please contact your local city
purchased this product.
Do not exceed the maximum wattage.
The mounting instruction must not be discarded.
Parallel arranging possible.
www.nordlux.com
Nordlux A/S – Ostre Havnegade 34 – 9000 Aalborg
In Denmark, outdoor lightings must be mounted by an
authorized electrician.
Mounting instruction
We congratulate you on your new outdoor lamp!
We congratulate you on
your new outdoor lamp!
Guarantee
The Nordlux Outdoor lamps in copper, bras s, tombac a nd galvanized
are guaranteed for up to 15 years. This guarantee applies to
extensive corrosion in the form of holes in the metal caused by rust.
The guarantee is subject to presentation of receipt.
There is not guarantee on the components which have
been damaged by wear and tear or mistreatment of the
lamps
We congratulate you on
your new outdoor lamp
Stainless steel
Remember to take care of your lamp. Just follow the guidelines below.
The shiny, uniform and decorative surface of stainless steel makes it
very suitable for outdoor use.
It is an alloy consisting of iron, chrome and nickel. During bath pickling,
a thin, rustproof oxide layer forms on the surface.
The surface is continually vulnerable to atmospheric conditions, and
from other effects of the close environment. This means that the lamp
must be regularly maintained if its surface is to remain shiny and untarnished
by rust.
Before setting it up, treat your lamp with acid-free oil, and dry it off with
a soft cloth. Repeat this three or four times a year.
Stainless steel lamps are not recommended for use in aggressive
environments such as coastal, agricultural or industrial areas.
Copper, Brass and Tombac fixtures
Our copper, brass and tombac fixtures are made from respectively solid
copper, brass and tombac. The mechanical machining will leave small
scratches in the surface, as well as residues of rinse aid. This rapidly
disappears in the patina process. After the first rain showers the copper
/ brass / tombak surface will appear stained, but the aerated air and
moisture will soon make the lamp appear with dark brownish color.
Over the years, the material copper will get a beautiful patina-green
color and brass / tombac will get a darker and more uniform color. The
uniformity of the patina surface, as well as the rate at which the process
occurs is dependent on the environment that affect the fixture.
Hot-galvanized lamps
The zinc treatment of the steel lamps is executed manually in plants.
The temperature of the melted zinc is about 460 degrees. When the
lamps are dipped in melted zinc a reaction between the metalls occurs,
which develops alloys in the surface.
The lamp and the components of the lamp are manually dipped in the
hot zinc. This treatment leaves variations in the coating in the form of
partly an uneven surface and partly minor formations of drops.
Thin »zinc curtains« might also occur on the surface and they show as
easily be removed or brushed off with a soft brush.
Condensation
Condensation is a phenomenon arising under specific atmosphere
conditions. Damp heat and cold air meet, which causes condensation
of water on the surface.
When water heats up it leads to rising water vapour, which will be able
to affect electric components.
Condensation is not included by Nordlux warranty, unless it is possible
to prove that a technical /production error in the lighting causes entry
of water.
In case of condensation please check:
– If the lighting is mounted according to instructions. Washers should
seal tightly. Make sure to tension screws and lenses.
-In garden lightings rising damp from the ground may cause condense material
into the metal post.
-It is highly important that drainage holes are kept free of impurities if
any.
BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO
WIPE OFF ALL PARTS!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>