SEALEY SCR18 Series Mechanics Utility Seat and Toolbox Instruction Manual
- June 3, 2024
- SEALEY
Table of Contents
SEALEY SCR18 Series Mechanics Utility Seat and Toolbox Instruction Manual
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction manual
SAFETY
♦ WARNING! Ensure Health & Safety, local authority, and general workshop
practice regulations are adhered to when using this seat.
√ Locate seat in a suitable working area.
♦ WARNING! Use the seat on level and solid ground, preferably concrete.
√ Keep the seat clean and tidy in accordance with good workshop practice.
⊗ DO NOT use the seat for any purpose other than that for which it is
designed.
⊗ DO NOT stand on the seat.
⊗ DO NOT use the seat outdoors.
⊗ DO NOT get the seat wet or use in damp or wet locations or areas where
there is condensation.
⊗ DO NOT clean the seat with any solvents which may damage the paint
surface or the protective coating on the padded seat.
⊗ DO NOT exceed maximum capacity of 136kg.
INTRODUCTION
Mobile utility seat, toolbox solution for keeping commonly used tools to hand.
Features two folding side trays for storing nuts and bolts during use. Twin
can capacity drinks holder and screwdriver storage rack on the rear. Four
Ø60mm oil resistant swivel castors for easy maneuverability.
Thick vinyl padded seat for added comfort. Suitable for the professional
workshop.
SPECIFICATION
Model no: ……………………………………………SCR18B,G,R,O,Y
Overall size W x D x H: ……………………..670 x 360 x 410mm
ASSEMBLY
Figure 1
Refer to Parts Diagram and fig.1
4.1. Carefully unpack contents. Seat (1), support tube (2) and support
frame (25) are pre-assembled.
4.2. Rest seat (1), support tube (2) and support frame (25) , upside down
in order to complete assembly. Use packaging to protect the seat.
4.3. FIT TRAYS
4.3.1. Fit trays onto the ends of the support tubes (2). Ensure trays are
orientated to hinge upwards.
4.3.2. Note the position of shorter screws (10). Longer screws (8) are used to
secure the connection plates (11) through the support tubes (2) and trays
(14).
4.3.3. Secure with flat washer (6) and domed nut (5). Leave nuts loose until
assembly has been completed then tighten securely.
4.4. FIT CASTORS (9).
4.4.1. Secure with castor nut (17).
4.5. FIT TWIN CAN HOLDER/STORAGE RACK
4.5.1. Carefully turn seat correct way up.
4.5.2. Use bolt (22) to attach to rear of seat.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
Note : It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important : No Liability is accepted for incorrect use of this product.
Warranty : Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
© Jack Sealey Limited
Original Language Version
SCR18 Series Issue:3 (4) 01/09/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>