CONSORT CSL2SC 2kW Convector Heaters Using SL Wireless Controllers User Guide
- June 3, 2024
- Consort
Table of Contents
CONSORT CSL2SC 2kW Convector Heaters Using SL Wireless Controllers
Introduction
All electrical appliances produced by the Company are guaranteed for one year
against faulty materials or workmanship. This applies only if the appliance
has been used for purposes in accordance with the instructions provided and
has not been connected to an unsuitable electricity supply, or subject to
misuse, neglect, damage or modified or repaired by any person not authorised
by us. This guarantee is offered to you as an extra benefit and does not
affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached
to the appliance.
Reasonable care has been taken to ensure that this guide is accurate at the
time of printing. In the interest of progress the Company reserve the right to
vary specifications from time to time without notice.
Overview
Please read this guide carefully and retain for future use and maintenance.
This appliance has been designed and manufactured to the highest international
standards, however, care must be taken for optimal results and safety. This
appliance also meets the requirements of EU Directive 2004/106/EC for EMC and
2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Warning
- Do NOT site the appliance in a corner.
- Do NOT handle the appliance with wet hands.
- Do NOT use the appliance in workshops or rooms where excessive dust is generated or present.
- Ensure that nothing is pushed into any aperture of this appliance.
- Do NOT touch outlet grille when the appliance is in use.
- Do NOT cover or restrict any aperture of the appliance when in use.
- Do NOT use the appliance if damaged.
- Do NOT leave the appliance unattended where young children are present.
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut-out (TOC). This is a safety device, which switches the heater off if, for any reason, the appliance overheats. The TOC can only be re-set after the appliance has cooled down. In order to re-set the TOC, proceed as follows:
- Switch off appliance and leave for approximately 10 minutes.
- Switch appliance back on and TOC will re-set.
- Ensure that the appliance is functioning correctly. If the TOC control operates again, the appliance should be checked by a competent electrician.
The heater carries a ‘Do Not Cover’ label to warn the user that if the appliance is covered, there is a risk of overheating.
Cleaning
Always disconnect the heater from the mains before cleaning. The heater should not require any maintenance, but it is strongly advised that it is kept clean. An occasional wipe over with a soft cloth is all that should be necessary.
- Do NOT use metal or furniture polish on any part of the heater.
- Do NOT touch the heater with wet hands or in any way bring water into contact with it.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
If Your Heater Does Not Work
- Check that power is available to the heater. The LED light should be illuminated
- Check that the thermal cut-out has not operated. Follow the reset instructions given under the section headed ‘Thermally Operated Cut-out’.
- Check that the fuse in the spur unit has not blown. This can be done by replacing the fuse with another suitable fuse.
Should none of the above remedies work, then telephone the helpline number shown in these instructions (UK ONLY). Do not attempt to repair the heater.
Connection to the Main Supply
Electrical installation should be carried out by a competent installer,
preferably registered with NICEIC (National Inspection Council for Electrical
Installation Contracting) in accordance with the 17th edition of the IEE
Wiring Regulations, (BS.7671), and any relevant Local Authority Bye-Laws. This
heater is fitted with a 3-core mains supply cable and must be permanently
connected to the electricity supply via a double pole switch having 3mm gap on
each pole. There are no exceptions. A switched Fused Connection unit to
BS.1363. Part 4 is a recommended mains supply connection accessory to ensure
compliance with safety requirements applicable to fixed-wiring installation.
Note : When switched on for the first time the appliance may emit a
slight smell. This is purely the evaporation of a fluid used in the
manufacturing process.
WARNING : This appliance must be earthed.
Operation
This heater can only be used when connected to any Consort SL wireless controller. Each SL controller can control any number of heaters providing they are within the RF range.
Please refer to the SL controller installation and control guide for full
operational details.
When the appliance is connected to the mains supply, the LED indicator will
light up green, showing that the power is available to the unit.
When the heat output has been enabled by a wireless controller, the LED
indicator light will turn red.
Please refer to the SL user and operating instructions for full operational
details.
Wall Mounting
The heater must not be located immediately below a fixed socket outlet.
The Wall Mounting brackets are packed separately in the carton. Fit the top
mounting brackets to the wall at the height and centers shown in the diagram.
Withdraw the two feet-securing screws from the base of the heater and use
these screws to secure the right-angled bracket to the base of the rear panel
of the heater in the correct holes. These are the holes in the two protruding
lugs.
Mount your appliance onto the top brackets via the two slots in the rear
panel. Secure the bottom bracket to the wall as shown.
WARNING : THIS APPLIANCE MUST BE EARTHED
IMPORTANT : ALWAYS RETAIN YOUR USER INSTRUCTIONS FOR FUTURE REFERENCE
CUSTOMER HELPLINE
Should you need any advice on the use of your new Consort product, please contact our Helpline:
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: 01646 692172 Fax: 01646 695195
Email: technical@consortepl.com Web:
www.consortepl.com
Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
BS EN ISO 9001 Registered Company No FM12671
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>