CONSORT PLE050 Panel Convector Heaters User Guide

CONSORT PLE050 Panel Convector Heaters

Quality Space Heaters

Installation & Control Guide for Panel Convector Heaters with Electronic Controls and Open Window Detection

Models

• PLE050
• PLE075
• PLE100
• PLE125
• PLE150
• PLE200/SS (Stainless Steel derivative)

All electrical appliances produced by the Company are guaranteed for one year against faulty materials or workmanship. This applies only if the appliance has been used for purposes in accordance with the instructions provided and has not been connected to an unsuitable electricity supply, or subject to misuse, neglect, damage or modified or repaired by any person not authorized by us. This guarantee is offered to you as an extra benefit and does not affect your legal rights.

The correct electricity supply voltage is shown on the rating label attached to the appliance.

Reasonable care has been taken to ensure that this guide is accurate at the time of printing. In the interest of progress, the Company reserves the right to vary specifications from time to time without notice.

Product Overview

Please read this guide carefully and retain for future use and maintenance. This appliance has been designed and manufactured to the highest international standards; however, care must be taken for optimal results and safety. This appliance also meets the requirements of EU Directive 2004/106/EC for EMC and 2009/125/EC Directive.

Product Safety & Care

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities orlack of experience and knowledge unless they have been given  supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Warning

Thermally Operated Cut-Out

The appliance is fitted with a thermally operated cut-out (TOC). This is a safety device, which switches the heater off if, for any reason, the appliance overheats. The TOC can only be re-set after the appliance has cooled down. In order to re-set the TOC, proceed as follows:

1. Switch off the appliance and allow it to cool down.
2. Check that the air inlet and outlet grilles are clean and not obstructed.
3. Switch on the appliance and check that it is working correctly.
4. If the appliance continues to switch off, disconnect from the mains supply and seek professional advice.

The heater carries a `Do Not Cover’ label to warn the user that if the appliance is covered, there is a risk of overheating.

Cleaning

any way bring water into contact with it. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

If Your Heater Does Not Work

Connection to the Main Supply

Product Installation

Before installation, ensure that the heater is fully secured in the vertical position before being switched on. It must be `clicked’ into the locking tabs. See section 15 for more mounting information.

Set Time

Press and hold for 5 seconds

Time Prog

Set Programme

Press and hold for 5 seconds

Temperature Set

When display shows room temperature, press to adjust

Temp Mode

Mode Selection

BOOST, MANUAL, SETBACK AND PROGRAM

Basic Operation

Before you can use the PLE, it has to be activated by pressing any control button. The LCD backlight will turn on. To operate any control button, press within 2 seconds of activation.

Usage Instructions

1. Before use, ensure that the heater is fully secured in the vertical position and clicked into the locking tabs.
2. To activate the heater, press any control button within 2 seconds of activation. The LCD backlight will turn on.
3. To set the time, press and hold the “Set Time” button for 5 seconds.
4. To set a program, press and hold the “Set Programme” button for 5 seconds.
5. To adjust the temperature, press the button when the display shows the current room temperature.
6. The heater has four modes: BOOST, MANUAL, SETBACK, and PROGRAM. Use the “Mode Selection” button to switch between modes.
7. The heater is fitted with a thermally operated cut-out (TOC) safety device. If the appliance overheats, the TOC will switch off the heater. To reset the TOC, switch off the appliance, allow it to cool down, check that the air inlet and outlet grilles are clean and not obstructed, and switch on the appliance again.
8. Do not cover the heater as this may cause overheating. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Installation & Control Guide for Panel Convector Heaters with Electronic Controls and Open Window Detection

Please note:
‘SS’ suffix added to model number denotes Stainless Steel derivative

All electrical appliances produced by the Company are guaranteed for one year against faulty materials or workmanship. This applies only if the appliance has been used for purposes in accordance with the instructions provided and has not been connected to an unsuitable electricity supply, or subject to misuse, neglect, damage or modified or repaired by any person not authorised by us. This guarantee is offered to you as an extra benefit and does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time of printing.
In the interest of progress the Company reserve the right to vary specifications from time to time without notice.

Overview

Please read this guide carefully and retain for future use and maintenance.
This appliance has been designed and manufactured to the highest international standards, however, care must be taken for optimal results and safety. This appliance also meets the requirements of EU Directive 2004/106/EC for EMC and 2009/125/EC Directive.

Safety & Care

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Warning

• Do NOT site the appliance in a corner.
• Do NOT handle the appliance with wet hands.
• Do NOT use the appliance in workshops or rooms where excessive dust is generated or present.
• Ensure that nothing is pushed into any aperture of this appliance.
• Do NOT touch outlet grille when the appliance is in use.
• Do NOT cover or restrict any aperture of the appliance when in use.
• Do NOT use the appliance if damaged.
• Do NOT leave the appliance unattended where young children are present.
• If used in a bathroom, the heater is to be installed so that the switches and other controls cannot be touched by a person in the bath or shower.
• Operating temperature range -10 to +40 ºc
• The heater MUST be fully secured in the vertical position before being switched on.

Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut-out (TOC). This is a safety device, which switches the heater off if, for any reason, the appliance overheats. The TOC can only be re-set after the appliance has cooled down. In order to re-set the TOC, proceed as follows:

• Switch off appliance and leave for approximately 10 minutes.
• Switch appliance back on and TOC will re-set.
• Ensure that the appliance is functioning correctly. If the TOC control operates again, the appliance should be checked by a competent electrician.

The heater carries a ‘Do Not Cover’ label to warn the user that if the appliance is covered, there is a risk of overheating.

Cleaning
Always disconnect the heater from the mains before cleaning. The heater should not require any maintenance, but it is strongly advised that it is kept clean. An occasional wipe over with a soft cloth is all that should be necessary.

• Do NOT use metal or furniture polish on any part of the heater.
• Do NOT touch the heater with wet hands or in any way bring water into contact with it.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

If Your Heater Does Not Work

• Check that power is available to the heater.
• Check that the thermal cut-out has not operated. Follow the reset instructions given under the section headed ‘Thermally Operated Cut-out’.
• Check that the fuse in the spur unit has not blown. This can be done by replacing the fuse with another suitable fuse.

Should none of the above remedies work, then telephone the helpline number shown in these instructions (UK ONLY). Do not attempt to repair the heater.

Connection to the Main Supply
Electrical installation should be carried out by a competent installer, preferably registered with NICEIC (National Inspection Council for Electrical Installation Contracting) in accordance with the 17 edition of the IEE Wiring Regulations, (BS.7671), and any relevant Local Authority Bye-Laws. This heater is fitted with a 3-core mains supply cable and must be permanently connected to the electricity supply via a double pole switch having 3mm gap on each pole. There are no exceptions. A switched Fused Connection unit to BS.1363. Part 4 is a recommended mains supply connection accessory to ensure compliance with safety requirements applicable to fixed-wiring installation.
Note: When switched on for the first time the appliance may emit a slight smell. This is purely the evaporation of a fluid used in the manufacturing process.
WARNING: This appliance must be earthed.

Installation

| M ILLIMETRES
---|---
W ATTS| A| B
PLE050| 500| 442| 303
PLE075| 750| 442| 303
PLE100| 1000| 614| 477
PLE125| 1250| 720| 582
PLE150| 1500| 720| 582
PLE200/SS| 2000| 852| 713

Note:

• The heater MUST be fully secured in the vertical position before being switched on.
• It must be ‘clicked’ into the locking tabs. See section 15 for more mounting information.

Basic Operation

Before you can use the PLE, it has to be activated by pressing any control button. The LCD backlight will turn on. To operate any control button, press within 2 seconds of activation.

Time and day setting

• Press and hold the TIME button for 5 seconds.
  Minutes are flashing – use TEMP and MODE buttons to set minutes.

• Press TIME button
  Hours are flashing – use TEMP and MODE buttons to set hours.

• Press TIME button
  Day is flashing – use TEMP and MODE buttons to set Day.
  Once you are happy with the settings, press ‘Time’ to return to main screen.

Selecting operating mode

PLE has 4 operating modes:
BOOST, MANUAL, SET BACK, PROGRAM.
Each mode can be selected by pressing the MODE button to cycle through the options. The cycle sequence will always start with BOOST mode followed by MANUAL, SET BACK and PROGRAM.

BOOST – 15 minutes

The boost feature increases the room temperature for 15 minutes.

1. Use TEMP and MODE to set the temperature.
   To amend the set temperature when in Boost mode, simply activate the display by pressing any button. Press TEMP, then use TEMP and MODE to change the temperature. Once the temperature is set, you can leave the display to return to the main screen and the settings will be saved. After 15 minutes, the PLE will return to previous operating mode.

MAN – Manual Mode

In manual mode, the heater maintains the set temperature.

1. Use TEMP and MODE to set the temperature.
   To amend the set temperature when in Manual mode, simply activate the display by pressing any button. Press TEMP, then use TEMP and MODE to change the temperature. Once the temperature is set, leave the display to return to the main screen and the settings will be saved.

SETB – Setback Mode

Setback mode can be used for frost protection, situations where a minimum room temperature must be maintained, or to disable the heating completely.
To amend the set temperature when in Setback mode, simply activate the display by pressing any button. Press TEMP, then use TEMP and MODE to change the temperature. Once the temperature is set, leave the display to return to the main screen and the settings will be saved. When the room temperature drops below the set temperature the heating will be active.
To disable heating lower the temperature to below 4ºc and she screen will show ‘- – -’ The heating is now disable.

PROG – Automatic time mode

In this mode, the PLE will follow the week’s time / temperature programme.
You can temporarily override the temperature in PROG mode by simply activating the display and using the TEMP and MODE buttons to set the new temperature. The new set temperature will be then maintained until the next program step.

Set 7-day programme

An example of one day programme on PLE

Logic diagram for setting programme on PLE

The PLE has a 7-day timer with up to 6 programming steps available for each day. In the programming you can set a start time and a temperature for each programme.

Set programme inactive.
If you do not require the use of all 6 programmes they can be set as inactive. When in programming mode select the programme you want to make inactive and press the TIME button. If the programme is inactive the display will show “- -:- -”. To activate the programme again press the TIME button.

1. Press and hold PROG for 5 seconds to enter the time setting.
2. The day will be flashing.
3. Use TEMP and MODE to navigate day, press PROG to select day.
4. PROG 1 will be flashing. Use TEMP and MODE to navigate programme, use PROG to select programme.
5. The minutes will be flashing.
6. To set minutes, use TEMP and MODE to change minutes, press PROG to set the minutes.
7. The hour will be flashing
8. To set hour, use TEMP and MODE to change hour, press PROG to set the hour.
9. The temperature will be flashing.
10. To set temperature, use TEMP and MODE to change temperature, press PROG to set temperature.

To add another programme repeat steps 2-10.
Copy day function.
If you require the same set of programmes throughout the week it is possible to copy all the programmes from one day to another.
To do this, when in programming mode press and hold the TIME button and this will bring you to the copy day mode. To select which day you wish to copy press the PROG button and this will cycle through numbers 1-7 on the screen, this relates to which day you would like to copy. 1=MON, 2=TUE, 3=WED etc.
To select which day you would like to copy the pro-grammes to, use the TEMP & MODE to navigate to the day. Once both are selected, press the time button to copy the day.

Advance mode

Press PROG from PROG mode to bring forward the next programme. To clear advance mode, press PROG.

Open Window Detection

Ensuring you don’t waste energy on heating the outside world, the heater is equipped with optional open / closed window detection. The heater recognises sudden drops in temperature when a window or a door is opened and turns the heating off to save energy. When the window is closed, the heater will automatically detect a temperature rise, and switch itself back on. Once enabled in the setup menu, the open window detection is fully automatic and does not require any human intervention to be activated.

Setting-up Open Window Detection
The system has been factory set to default time and temperature values. If necessary, all values can be adjusted. When the heating is on, open window detection sensor will automatically switch the heater off when it detects a fall in temperature of 2°C in less than 10 minutes (this temperature can be changed in menu 7 and time in menu 6). If a temperature rise of 2°C in less than 30 seconds is detected, the heater will switch itself back on (this temperature can be changed in menu 9 and time in menu 8).

Setup menu

1. Press and hold TEMP and MODE together for 5 seconds.

2. The display will enter the setup menu.

3. Use TEMP and MODE to change a value.

4. Use TIME to scroll between the settings.

5. temperature calibration
   The temperature reading has been factory calibrated but if for any reason it needs adjusting (better accuracy required, to suit different position in the room etc.), the reading can be recalibrated in 0.5 degrees steps.

6. change between degrees Celsius or Fahrenheit

7. set minimum temperature
   (3.5 deg = frost protection)
   When this is set, the heater will operate in any mode should the room temperature fall below the set temperature.

8. set maximum temperature
   When this is set, the maximum temperature in any mode cannot exceed the limit.

9. 05 – open window detection 0 = off, 1 = on

10. 600 – open window detection time 600 seconds

11. 2 – temperature drop of 2°C in the detection time

12. 30 – closed window detection time of 30 seconds

13. 2 – temperature rise of 2°C in the detection time

Heat symbol on the display

Every time there is a demand for heat, the display will show the heat icon.

– full heat output

Keys locking

Press and hold TIME and TEMP together for 5 seconds. The display will show symbol. Repeat the step to unlock.

Optional PLK1 Locking Device

The PLK1 locking device can be used to mechanically lock the controls to prevent tampering with settings. As it is not supplied with the heater, kindly contact our Sales team if required.

Locking tab
Locking screw

Mounting

To wall mount, the wall bracket supplied must be used. Please refer to illustrations in Fig.1.
Remove wall bracket from the heater. Fix wall bracket to wall using screw holes provided. Present heater to bracket. Locate heater onto bottom lugs via 2 sets of relevant slots in rear panel. Hinge heater upwards and locate the top tabs into the slots in the back of the heater and ‘click’ into position. The heater MUST not be powered until it is in this position.
To remove the heater from the wall first disconnect the power then press down on the two top tabs to release the heater. Hinge the heater forward on the bottom lugs. The heater can be now lifted off the bottom lugs to remove it from the wall. The heater must not be located immediately below a fixed socket outlet.

Declaration Of Conformity

In accordance with UK Government Guidance.
WE HEREBY CERTIFY THAT THE APPLIANCES DETAILED HEREON HAVE BEEN INSPECTED AND TESTED, AND CONFORM TO THE REQUIREMENTS OF THE FOLLOWING UK STATUTORY INSTRUMENTS WHERE APPLICABLE:

• Electrical Equipment (Safety) Regulations 2016 SI. 2016 1101
• Electromagnetic Compatibility Regulations 2016 SI. 2016 No. 1091
• Radio Equipment Regulations 2017 SI. 2017 No. 1206
• The Ecodesign for Energy Related Products and Energy Information (Amendment) (EU Exit) Regulations 2019. SI. 2010 2617
• The Restriction of use of Certain Hazardous Substances. SI. 2012 No. 3032
• The Waste Electrical and Electronic Equipment Regulations 2013. SI. 2013 No. 3113

Transposed standards used:

• BSEN55014 (2006)
• BSEN301 489.1 & .3
• BSEN300 220.1 & .2
• BSEN60 730.2.9
• BSEN 60335.1 (2012 )
• BS EN 60335.2.30 (2009)

PART NUMBER AND DESCRIPTION OF APPLIANCE: PLE050, PLE075, PLE100, PLE125, PLE150 and PLE200/SS Panel heaters
NAME OF RESPONSIBLE PERSON: LEE GRIFFITHS
POSITION: PRODUCTION AND QUALITY MANAGER
DATE: 26/01/22

CONSORT EQUIPMENT PRODUCTS LTD.
THORNTON INDUSTRIAL ESTATE, MILFORD HAVEN, PEMBROKESHIRE, SA73 2RT. UK

• TEL: +44 1646 692172
• FAX: +44 1646 695195.
• E-MAIL: ENQUIRIES@CONSORTEPL.COM
• WWW.CONSORTEPL.COM

References

• Consort Claudgen - Electric Heating Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>