BALBOA CLIM8ZONE spaTouch 3 User Guide
- June 3, 2024
- BALBOA
Table of Contents
CLIM8ZONE spaTouch 3
User Guide
CLIM8ZONE spaTouch 3
THANK YOU
for using Balboa Water Group spa controls.
Please visit us at
www.BalboaWaterGroup.com
http://www.balboawatergroup.com/
TEMPERATURE MODES
CLIM8ZONE has four Temperature modes for heating/cooling spa water.
-
HEATING MODE (Default)
This mode only heats the spa water. All cooling with the CLIM8ZONE TM unit is disabled. -
COOLING MODE
This mode only cools the spa water. All heating with the CLIM8ZONE TM unit is disabled. -
HEATING AND COOLING MODE (Default)
This mode heats and cools the spa water with the CLIM8ZONE TM unit enabled. -
DISABLED
eHeater MODES
The BP control system has three eHeater modes.
-
CONTINUOUS
The electric heater (eHeater) is continuously enabled. -
eBOOST (Default)
The electric heater is enabled temporarily when an extra boost is required. -
DISABLED BP Control System with eHeater
SPEED MODES
CLIM8ZONE has three Speed modes.
-
AUTO SMART (Default)
• For Heating or Cooling
• Uses Artificial Intelligence
• Variable Heating/Cooling capacity
• The CLIM8ZONE TM computer automatically adjusts the compressor frequency up or down using an algorithm that is based on ambient air temperature and water temperature.
• This algorithm balances a best case in most conditions for efficiency and noise vs heating/cooling output of the CLIM8ZONE unit. -
MANUAL HIGH
• For Heating or Cooling
• Highest Heating Capacity
• Fastest Water Heating/Cooling
• Low COP (i.e. Low Energy Efficiency)
• High Compressor Frequency – Fixed, i.e. does not adjust based on environmental conditions
• The CLIM8ZONE unit Compressor Noise is Maximum -
MANUAL LOW
• For Heating or Cooling
• Lowest Heating/Cooling Capacity
• Slowest Water Heating
• High COP (i.e. High Energy Efficiency)
• Low Compressor Frequency – Fixed, i.e. does not adjust based on environmental conditions
• The CLIM8ZONE unit Compressor Noise is Minimum
SET THE TEMPERATURE MODE
Follow these steps to set the Temperature mode.
-
Press the Settings button (A) to enter the Settings screen.
-
Press the CLIM8ZONETM button (B) to enter the CLIM8ZONE TM screen.
-
Press the CLIM8ZONE TM button (C) to enter the CLIM8ZONE TM screen.
-
Select one of the following Temperature modes (E):
Heat Only (Default)
Cool Only
Heat and Cool
Disabled -
Press the Save button (D) to save your setting. Press the Cancel button (F) to cancel your setting.
Your setting is complete. ☑
SET THE SPEED MODE
Follow these steps to set the Temperature mode.
-
Press the Settings button (A) to enter the Settings screen.
-
Press the CLIM8ZONE TM button (B) to enter the CLIM8ZONE TM screen.
-
Press the Speed button (C) to enter the Speed screen.
-
Select one of the following Speed modes (E):
Manual High
Auto Smart (Default)
Manual Low -
Press the Save button (D) to save your setting. Press the Cancel button (F) to cancel your setting.
Your setting is complete. ☑
SET THE eHE ATER MODE
Follow these steps to set the eHeater mode.
-
Press the Settings button (A) to enter the Settings screen.
-
Press the CLIM8ZONE TM button (B) to enter the CLIM8ZONE TM screen.
-
Press the eHeater button (C) to enter the eHeater screen.
-
Select one of the following eHeater modes (E):
Disabled
Continuous
eBOOST (Default) -
Press the Save button (D) to save the new setting. Press the Cancel button (F) to cancel the setting change.
Your setting is complete. ☑
Email: info@balboawater.com
Phone:
P : + 714.384.0384
Customer Service is available:
M – F 7:00AM to 6:00PM PT
Corporate Office
Balboa Water Group
3030 Airway Avenue
Costa Mesa, CA 92626
MEXICO OPERATIONS
Balboa Water Group
Aguila Azteca 6011
Baja Maq. El Aquila
Mexico 22221| EUROPEAN OPERATIONS
Balboa Water Group
Hydroair International
ApS Roustvej 50 DK-6800
Varde
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>