homestyles 5427-691 Pantry User Manual
- June 8, 2024
- homestyles
Table of Contents
5427-691
Pantry
User Manual
5427-691 Pantry
IMPORTANT
Carefully remove all the parts from the carton and place them individually on
a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions to ensure a
completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
Hardware List
Assembly Instructions
IMPORTANT
- Use a soft cloth between these parts and the floor.
- Do not use power tools above 8 volts to assemble.
- Do not tighten all the screws until each part is properly assembled.
- The unit must be level to work properly. Use the included adjustable levelers to level.
- Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Rail (N) to Side Panel (B),
then flip Lock. (See Figures 1 and 2)
Slide Back Panel (I) into position.
Attach Upright (J) to unit.
Slide Back Panel (I) into position.
Attach Rail (N) to unit, then flip Lock.
STEP 2
Attach Magnet to Rail (M) with Wood Screws for Magnet into pre-drilled holes.
(See Figure 3)
Attach Rail (M) to unit with Wood Screw (long).
Attach Side Panel (C) to unit, then flip Locks.
Insert Wood Screw (long) into pre-drilled hole in unit, then tighten.
STEP 3
Place Base (E) upside down on a soft cloth.
Attach Feet (F) to Base (E).
STEP 4
Turn over base unit to its upright position.
Attach unit from Step 2 to base unit, then flip Locks.
Attach Middle Panel (D) to unit, then flip Locks.
STEP 5
Place Top (A) upside down on a soft cloth.
Attach Magnet to Top (A) with Wood Screws for Magnet into pre-drilled
holes.
STEP 6
Attach Rail (N) to Side Panel (G), then flip Lock.
Slide Back Panel (K) into position.
Attach Upright (L) to unit.
Slide Back Panel (K) into position.
Attach Rail (N) to unit, then flip Lock.
Attach Side Panel (H) to unit, then flip Locks.
STEP 7
Attach unit from Step 5 to unit from Step 4, then flip Locks.
Insert Adjustable Pins into side panels at desired level.
(See Figure 4)
Drawer (T)
STEP 8
Attach Drawer Sides (T3) and (T4) to Drawer Back (T2), then flip Locks.
(See Figures 5 and 6)
STEP 9
Slide Drawer Bottom (T5) into groove.
Attach Drawer Front (T1) to unit, then flip Locks.![homestyles 5427 691 Pantry
- STEP 9](https://manuals.plus/wp-content/uploads/2023/01/homestyles-5427-691 -Pantry-STEP-9.jpg)
STEP 11
Place Shelves (S) into position.
Attach Doors (O), (P), (Q) and (R) to unit by sliding door hinges into side
panel hinges. (See Figure 7)
Attach Knobs to Doors (O), (P), (Q) and (R) with Machine Screws (long).
Attach Top (A) to unit, then flip Locks.
Slide Drawer (T) into position.
STEP 12
Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure
8) Insert Wood Screws into pre-drilled holes in unit, then tighten.
Note: Unit must be level before tightening these screws.
IMPORTANT
- To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
STEP 13
Place unit at desired location.
Drill a 3/8” hole in wall in-line with the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through Bracket on wall and Bracket on unit.
(See Figure 9)Put tie
end of Tipover Restraint into lock end of Tipover Restraint and pull until
tight.
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp and split and finishes to delaminate.
NEVER
use glass cleaners on finished furniture. Ammonia chemically attacks the
finish.
|
---|---
Do not use power tools above 8 volts to assemble.
PREVENT CRACKING| Do not place in direct sunlight.
PREVENT FADING
|
Do not write directly on surface.
PREVENT MARKING| Do not place hot objects on surface.
PREVENT FINISH DAMAGE
|
Do not use rubber based placemats.
PREVENT DISCOLORING| Do not use commercial waxes and polishes.
PREVENT YELLOWING
CLEAN with a
soft cloth moistened in lukewarm soap and water.
Buff with a dry clean cloth.
home styles will provide replacements free of charge for missing or damaged
parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not
purchased from an authorized retailer, home
styles is under no obligation to provide replacement parts. Parts are not
available for fully assembled items nor are parts available for sale.
Replacements for missing or damaged parts may be requested via contact info
below.
home styles Customer Service:
www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
888-680-7460
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>