aube technologies TH114-A Non-Programmable Thermostat Owner’s Manual
- June 4, 2024
- aube technologies
Table of Contents
- aube technologies TH114-A Non-Programmable Thermostat
- Before you start
- About your thermostat
- Supplied Parts
- Controls and display
- Temperature Display and Setting
- Installing the thermostat
- Connecting the floor temperature sensor
- Wiring diagram
- Multiple SSRs with External Transformer
- Electromechanical Relay with External Transformer
- Hot Water Heater Valve
- Setting the configuration switches
- To select the F Mode, connect the floor temperature
- Floor temperature limits AF mode only
- Error Messages
- Technical Specifications
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
aube technologies TH114-A Non-Programmable Thermostat
View all aube thermostat manual
Before you start
CAUTION
For a new installation, choose a location about 1.5 m (5 ft.) above the
floor. The thermostat must be installed on an inside wall facing the heating
system except for floor heating systems. Avoid locations where there are air
drafts (top of staircase, air outlet), dead air spots (behind a door), direct
sunlight, or concealed chimney or stove pipes except for floor heating
systems. Do NOT install the thermostat in an area where it can be exposed to
water or rain. Keep the thermostat’s top and bottom air vents openings clean
and unobstructed at all times.
About your thermostat
The TH114-A/AF-024T non-programmable thermostat has three temperature control modes
A mode
Controls the ambient air temperature
F mode
Controls the floor temperature
AF mode
Controls the ambient air temperature maintains the floor temperature within desired limits.
Supplied Parts
- One (1) thermostat
- Two (2) mounting screws
- Two (2) plastic anchors
- Select models only; required for filoor heating applications only.
- One (1) floor sensor
- One (1) flat tip screwdriver.
Controls and display
Temperature Display and Setting
The thermostat usually displays the room temperature. To view the set (desired) temperature, press either of the AV buttons once. The set temperature is displayed for5 seconds. To set a new temperature, press one of the AV buttons repeatedly until the desired temperature is displayed. To scrol faster, press and hold the button.
Backlight
The display illuminates for 5 seconds when the backlight button is pressed. When either of the AY buttons is pressed, the display illuminates for 10 seconds. The set temperature appears for the first 5 seconds, then the room temperature is displayed.
On/Standby Switch
You can set the thermostat to Standby to cut power to the heating system when it is not in use e.g. in summer. The thermostat screen becomes blank but all settings are saved.
Installing the thermostat
- Turn the heating system off at the main electrical panel .
- Loosen the bottom screw and remove the thermostat faceplate from its wall plate.
- The screw cannot be completely removed.
- Wire the thermostat.
- If the thermostat will be used in F or AF mode connect the floor sensor.
- Install the wall plate on the wall using the provided screws and wall anchors.
- Set the configuration switches.
- Install the faceplate back on the wall plate and tighten the screw.
- If there is a sticker on the screen, peel it off.
- Retune power to the heating system at the main electrical panel.
Connecting the floor temperature sensor
Wiring diagram
Single SSR with Built in Transformer
Multiple SSRs with External Transformer
Electromechanical Relay with External Transformer
Hot Water Heater Valve
Setting the configuration switches
Configuration switches are on the back of the faceplate.
# | Configurations | Up | Down |
---|---|---|---|
S1 | Displayed temperature unit | °F | °C |
S2 | Temperature control mode | F | AF |
To select the F Mode, connect the floor temperature
To select the AF Mode, proceed as follows: Connect the floor temperature sensor. Place the switch in the F position. If the thermostat displays Er, the sensor is improperly connected or damaged. If the thermostat displays a temperature reading, place the switch in the AF position. To select the A Mode, place the switch in the AF position but do NOT connect the floor temperature sensor.
Floor temperature limits AF mode only
The minimum and maximum floor temperature limits are available only if the temperature control mode is AF. If the floor temperature drops below the minimum limit or rises above the maximum limit, the thermostat will turn heating On or Off respectively, regardless of the ambient temperature, to maintain the floor temperature within the set limits.
NOTE
The desired ambient temperature might not be attainable if the maximum floor
temperature is set too low. The minimum and maximum floor temperature limits
are factory-set at 10 °C (50 °F) and 28 °C (82 °F) respectively. To modify the
limits, proceed as follows:
WARNING
To avoid damaging your floor, follow your floor supplier’s recommendations regarding floor temperature limits. Switch the thermostat to Standby. While pressing either button , up and down switch the thermostat back to On to access the floor temperature limit settings. Press the Backlight button briefly to switch between minimum and maximum floor temperature settings. Press the up and down buttons to set the desired limit. Press the Backlight button for 3 seconds to save your modifications. After the data are saved, the thermostat displays the current temperature.
NOTE
Your modifications are automatically saved if no button is pressed for 60
seconds.
Error Messages
L0
The measured temperature is below the display range. Heating is activated.
H1
The measured temperature is above the display range. Heating is deactivated.
Er
Verify the thermostat and sensor connections. Heating is deactivated.
Technical Specifications
- Maximum load: 0.5 A / 24 VAC
- Wire gauge: 14 to 22 AWG
- Heating cycle length: 15 minutes
- Setpoint range F mode: 5 °C to 40 °C (40 °F to 104 °F)
- A/AF mode: 5 °C to 30 °C (40 °F to 86 °F) Floor limit range AF mode: 5 °C to 40 °C (40 °F – 104 °F)
- Display range F mode: 0 °C to 60 °C (32 °F to 140 °F)
- AF mode: 0 °C to 50 °C (32 °F to 122 °F) Resolution: 0.5 °C (1 °F)
- Data protection: All settings are saved during a power failure.
Warranty
Return it, with a bill of sale or other dated proof of purchase, to the
place from which you purchased it, or Customer Care will make the
determination whether the product should be returned to the following address
Resideo Return Goods, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether
a replacement product can be sent to you. This warranty does not cover removal
or reinstallation costs. This warranty shall not apply if it is shown by
Resideo that the defect was caused by damage which occurred while the product
was in the possession of a consumer. Resideo’s sole responsibility shall be to
repair or replace the product within the terms stated above. RESIDEO SHALL NOT
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF
ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some
states do not allow the exclusion or limitation of incidental or consequential
damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY
EXPRESS WARRANTY RESIDEO MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE YEAR DURATION OF THIS
WARRANTY. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. This warranty gives you
specific legal rights, and you may have other rights which vary from state to
state. If you have any questions concerning this warranty.
https://thermostat.guide/aube/aube-technologies-th114-a-non-programmable- thermostat-owners-manual/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>