HUILILOCK D1 Smartcode Electronic Lock User Guide

HUILILOCK D1 Smartcode Electronic Lock User Guide

Please keep this guide This guide contains important information about your lock.

Overall

1. Backup Key
2. Exterior Assembly
3. Latch
4. Screw
5. Screw
6. Striking Plate
7. Mounting Plate
8. Screw
9. Interior Assembly
10. Battery Cover

Tips: Specifications are subject to change without prior notice.

Parts List

• Backup Key

• Exterior Assembly

• Latch

• Screws for Latch/Striking Plat

• Striking Plate

• Mounting Plate

• Screws for Mounting Plate and Exterior Assembly

• Interior Assembly

• Battery Cover

• Screws for Interior Assembly
  

• Reset Tool

• Hole-Aligning Device

Adjustable Deadbolt Latch Set

1. TO CONVERT BACKSET FROM 2-3/8” (60mm) TO 2-3/4″ (70mm)
   a Rotate the latch in a clockwise direction, then pull out, and twist the extension plate in an anti clockwise direction until hear a lock sound.
   

2. TO CONVERT BACKSET FROM 2-3/4” (70mm) TO 2-3/8″ (60mm)
   a. Rotate the latch in an clockwise direction, then push in until the end, and twist the extension plate in an anticlockwise direction until hear a lock sound.
   

Installation Guide

1. PREPARE THE DOOR AND CHECK DIMENSIONS (with the TEMPLATE card)

   • A: Measure to confirm the size of hole in the door frame. The wide is 1″(26mm), the length is 1-1/4″(30mm), the depth is 1-1/47(80mm).
     

   • B: Measure to confirm the thickness of door is 1-1/4″ to 2″ (30mm-50mm), the hole in the side of door is 1″ (26mm).
     

   • C : Measure to confirm the backset is 2-3/8” or 2-3/4” (60mm or 70mm). And adjust the length of the latch accordingly.
     

   • D : Measure to confirm the size of hole in the daor is 2-1/8″ (54mm).

2. INSTALL THE LATCH AND STRIKING PLATE

   • A ; Instal striking plate and hole-aligning device in the door frame with two screws (D) provided.
     

   • B : Insert latch into hole in side of door with the word “UP” up, and screw latch inta door with two screws (D) provided.
     
     IMPORTANT: Please make sure the lateh bolt is fully retracted (in the unlocked position) before installation.
     
     

3. INSTALL THE EXTERIOR ASSEMBLY AND MOUNTING PLATE
   IMPORTANT: Please make sure the latch bolt is fully retracted (in the unlocked positian) before installation.

   • A : Insert torqus blade horizontally through slot in the latch, and route the cable below the latch.
     

   • Install mounting plate with tow screw (G) provided.
     
     
     Make sure the screws ere in the correct position.

4. INSTALL THE INTERIOR ASSEMBLY AND BATTERY COVER

   • A : Connect the cable and ensure connection is tighten install interior assembly with three screws (l) provided.
     IMPORTANT: Please make sure the knob is in vertical position, and the latch bolt is fully retracted (in the unlocked position) before installation.
     
     

   • B : Load 4 batteries and install the C battery cover.
     

   • C : Finish Installation.
     

5. **DETECT LEFT/RIGHT HAND DOOR INSTALLATION
   

** Click the keypad King Force, the lock will go into locking position automatically. This is for the smart lock to N N ” – D Press New User Code New User Code memorize the orientation of the door.

Factory Default Settings

1. MASTER CODE
   Required for programming and feature settings. Master code can be used to unlock the door under vacation mode.
   Property owner/manager should keep this information confidential.

2. AUTO LOCK
   ‘The lock villbe automatically locked in setting seconds after unlocking if auto lock enabled.

3. WRONG ENTRY LIMIT
   After 10unsuccessful attempts at entering a valid pin code, the unit will shut down for 30 seconds.

4. SILENT MODE
   The beep sounds can be muted when pressing keypad. But you will till hear key prompts such as alerts.

5. VACATION MODE
   This is a security feature for you when you are leaving your home for vacation o long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. Inputting any User Code causes 2 short beeps. Inputting wrong Master Code causes 3 short beeps.

6. UNLOCK DIRECTION
   The machine has function of automatically judging unlocking direction.
   ‘When noting use or reset, unlocking direction is not determined. When pressing key to unlock lock first-time, it will automatically find unlock lock direction. It will records if successful, then it will be executed based on record. There will be 3 short sound prompts if felled, Tawil continue to look for unlocking direction next time. Manually turning knob to unlock lock will not record unlocking direction. need to change unlocking direction after recorded, disconnect the power and reconnect i, then successfully unlock ion cu one time.

7. UNLOCK METHOD
   Enter the password and press the keypad King Forces to unlock. Manually tum the knob to unlock.

8. LOCKING METHOD
   Click keypad King Force to lock. Manually tum the knob to lock. If the auto lock is enabled, the lock will be automatically locked after the set time is over.

9. LOW BATTERY ALARM
   When the correct unlock password is entered, the battery power will be automatically detected, if the voltage under below 4.8V(z 0.1), five. short beeps wil be prompted.

10. Emergency power supply
    The USB TypeC interface below the front panel can be connected to ‘2 mobile power supply for emergency unlocking.

Parts Illustrations

Exterior Assembly

The default Master Code is 123456 .

Interior Assembly

Programming Instructions

1. MASTER CODE (4 to 10 digits)
   The default Master Code is 123456.

2. USER CODE (4 to 10 digits)
   Atotal of 20 User Codes and one temporary one-time User Code may be programmed. If the password is unlocked unsuccessfully, please reset the password according to [Quick Set Up-

3. .Add User Code] carefully.

Quick Set Up

The default Master Code is 123456,

• 3short beeps appear at every wrong and overtime step.
• 1 long beep means you can go on until succeed.
• While you enter Management mode, you will see all keypads light flash constantly.

Note: King fierce the Multi-Function button in Exterior Assembly.

• 
  • Note: You will enter Management Mode only in lock state.
• 
  • default master code: 123456
• 
• 
• 
• 
  • Note: While Vacation mold enabled, if you use master code to unlock or enter management mode, then Vacation mode will be disabled.
• 

Restore To Factqry Default Settings

The default Master Code is 123456

1. Open and unlock the door.
2. Take out one battery, then press random keypad to consume the rest power.
3. Press the Reset Button with the Reset tool (K), then keep pressing and place the battery back.
4. Keep holding the Reset Button until you hear 2 beeps. (fjust hear one beep, please do it a from step 1)

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. This device may not cause harmful interference.
3. This device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be
determined by turning the equipment off and on,the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Get 24/7 Assistance at

Use camers or QR scanner o scan

Visit: https://kingforce.afterservice.vip
Email; kingforce@afterservice.vip
Call: +1(388) 839 1709

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>