GYROOR W2 In Line Skates User Manual
- June 3, 2024
- GYROOR
Table of Contents
GYROOR W2 In Line Skates
Learn more News about the Gyroor inline skate?
Scan “Gyroorboard” Messenger QR code to get it soon.
The manufacturer reserves the right to make changes to the product, and
updates this manual at any time.
Visit www.gyroorboard.com to download the latest
user manual.
www.gyroorboard.com
Congratulations!
You have chosen to purchase a high quality product.
Fomiliarise yourself with the product before using it for the first fime.
Read the following instructions for use carefully.
Use the product only as described and only for the given areas of application.
Store these instructions for use carefully. When passing the product on to
third parties, please also hand over all accompanying documents.
Package contents/parts list (Fig. A)
- 1 x inline skates (1)
- (1a) flap
- (1b) pressure slide
- (1c) quick-fastening fastener
- (1d) shoelaces
- (1e) velcro tongue-fastener
- (1f ) click fastener
- (1g) ratchet band
- (1h) sider for the quick-lacing fastener
- (1i ) dressing aid
- (1j ) setting button
- (1k) symbols for sizing
- 1 x replacement stopper (2)
- 2 x allen keys (3)
- 2 x replacement wheel
- 1 x instructions for use
Technical data
- Sizes: 10J – 7
- Rollers: 64 x 24mm, 70 x 24mm, 72 x 24mm
- Ball bearings: ABEC-7 carbon steel bearings
- Wheel: PU polyurethane
- Frame: Aluminum alloy
- Buckle: PP+PE
- Liner: Breathable mesh (polyester + nylon)
- Lining: polyester + nylon
- Shell: PP+PE
Date of manufacture (month/year): 7/2021
Size Chart
Intended use
These inline skates have been manufactured for fitness and recreational use for private use, not suitable for street hockey or aggressive skating.
Safety information
Risk of injury!
- Keep an eye on other traffic and follow traffic rules.
- Ensure the correct surface for your inline skating activities. Surfaces should be smooth clean and dry.
- Before you skate, check that all screws and nuts are tight.
- Make sure that the nuts and bolts retain thein self-locking properties.
- Do not modify the item in a way that might endanger your safety.
- Remove sharp edges that can occur during skating.
- Always wear suitable protection (helmet, hand protectors, elbow pads, knee pads and wrist guards).
- Avoid areas with dense traffic. Remain vigilant and be careful.
- Avoid excessively high speeds. Rule of thumb Never skate faster than you can run.
- Replace brakes, rollers and ball bearings when these become worn.
- Always wear reflective apparel so that you are visible.
- Do not use the item barefoot.
Preventing damage to the item!
- Maintain your inline skates.
- Avoid water, oil, potholes and very rough surfaces.
Tips for skating
Note:
We recommend skating in skate parks, as well as a skating course with a
teacher.
Initial training
Starting position:
feet shoulder-width, bend your knees slightly to prevent falling backwards.
Speeding up:
Start with small steps, as a beginner, keeping your feet pointed to the front
at an angle.
Rolling:
lf you take a few initial steps, you’ll have enough momentum to place both
skates side by side and roll. Bend your knees slightly when doing this.
Fall technique Important!
Practice falling on your protective gear first without inline skates, on a soft
surface.
Always try to steer falls forwards, never back-wards! Let yourself fall onto
the knee guards. Then brace yourself with elbow and hand guards. Spread your
fingers while dong this, to prevent injuries.
Mastering bends
At low speeds:
Spread your weight in the same way as when you ride a bicycle. Spread your
weight to your left foot for a left bend, and on your right foot for a right
bend.
At high speeds:
Cross over in the same way as ice-skating (Fig.B).
Braking techniques
Note:
Practice various braking techniques on an even surface, with no traffic or
pedestrians.
Prevent falls until you have mastered the braking techniques.
Heel braking technique (Fig.C):
If your inline skates are equipped with brakes, ensure that you use them. The
brake is mounted, lightly apply and press the brake to the ground. Shift your
weight slightly forward and bend your knees. The braking effect can be
enhanced if you bend your knees more and move your weight further forward
while at the same time increasing the pressure on your braking skate.
T-Brake (Fig.D):
lf your inline skates are not equipped with a brake or you have dismounted the
brake, we recommend the use of the “T-Stop-Technology” – however, this is only
suitable for advanced skaters! When using the “T-Stop technology”, you shift
your entire weight on one foot. Now move the other foot behind the first one
and place it behind it at right angles.
Then shift your weight from the front to the inside of the rollers of your
rear skate and brake with increasing pressure.
Setting the size (Fig.E)
Press the setting button down (1i) and shift the shoe while holding down the
setting button, setting the correct size.
The shoe must click in, and you must hear a clear “CLICK” sound. The arrow on
the shoe shows the size (1k) on the frame.
Setting the width (Fig. F)
Loosen the screw on the underside of the item with the Allen (3) key delivered
with the item by turning it in the direction of the arrow.
Adapt the width to your individual requirements by sliding the shoe. Tighten
the bolt again afterwards.
Putting skates on
Preparing for putting on the skates, from its factory setting
Important! Make sure that your inline skates fit properly/correctly.
The outer boot should not deform when the quick-release fastener is closed.
Don’t close the quickrelease fastener with force.
-
Press the pressure slide (1b) of the quick-release fastener (1c) in the direction of the arrow and open the quick-release fastener(1c)(Fig.G).
-
Press the latch (1f) and pull the ratchet strap(1g) out of the opening of the latch (1f)(Fig.H).
-
Open the Velcro tongue-fastener (1e)(Fig.l)
-
Set the slider of the quick-release fastener (1h) to OPEN and loosen the quick-release fastener (Fig.J).
-
Put on the inline skates with the help of the dressing aid (1i)(Fig.K).
-
Pull the shoelaces (1d) out from behind the flap (1a) and pull them tightly upwards(Fig. L). While doing this, pull on each shoe-lace, (1d) interchanging.
-
Lock the quick-release fastener by sliding the quick-release fastener (1h) lock slider to CLOSE (Fig.M).
-
Tie a loop from both ends of the laces (1d) and put it back behind the flap (la)
-
Close off the Velcro tongue-fastener (le).
-
Slide the ratchet strap (1g) into the opening provided under the latch (1f) and set the correct tension for you (Fig. N).
Note! To find the right tension for your foot, push the latch diagonally upwards and move the ratchet strap to the correct position. -
Close the quick fastener (1c)(“CLICK”)
Taking skates off
- Press the pressure slide (1b) of the quick-release fastener (1c) in the direction of the arrow and open the quick-release fastener(1c)(Fig.G).
- Press the latch (1f) and pull the ratchet strap(1g) out of the opening of the latch (Fig. H).
- Open the Velcro tongue-fastener (1e)(Fig.I)
- Set the slider of the quick-release fastener(1h) to OPEN and loosen the quick-release fastener (Fig.J).
Maintenance
Replacing the brake (Fig. O)
Note: worn brakes are dangerous! The braking effect can be reduced. Check
for brake wear before each journey. If braking control or effectiveness dete-
riorates before the wear limit mark is reached, the brakes must be replaced.
At the latest, replace the brakes when they reach the wear limit mark (1t).
- Unscrew the brake block screw (1n) of the inline skate (1) with the enclosed hexagon socket wrenches(3).
- Pull out the brake block screws (1n) and remove the brake block (1m) from the brake block holder (1l).
- Attach the new brake block (1I) firmly to the brake block holder (1n] using the brake block screws(1m).
Replacing the rollers (Fig. P) Important!
-
See the chapter “Technical data”: Wheels with a different diameter may alter the skating properties
and possibly endanger the user. Therefore, please do not use if the rollers cannot be installed correctly. Never install larger rollers than the original rollers of the inline skates. -
Please note the following for the axle bolts: After loosening the screw connection, you must apply self-locking paint to the thread of the screws again! We recommend that you always follow this as a precaution. Self-securing lacquer is available in DIY stores or specialist shops.
Wheels wear out. This wear depends on many factors, such as the style of skating, the surface, the size and weight of the user, the weights, the material of the wheels and their hardness. lt is therefore necessary to replace them regularly.
- Screw the axle screws (1q) of the inline skate out of the frame (1p) using the Allen keys.
- Pull out the axle bolts (1q) and remove the wheel (1o).
- Reinstall the new roller (1o) in the frame (1p) and fix it with the axle bolts (1q).
After replacing the wheels:
lf after the replacement the roller grinds side ways or touches the frame at
the circumference please do not use the roller! After the first few minutes of
skating, make sure that all screws are still tight and that nothing has
detached or become loose. Retighten the rollers individually to ensure that
they run smoothly and that there is no noise from the bearings.
Important!
New rollers upgrade the inline skates overall. This changes the distance to
the ground and therefore also the braking properties. For this reason, replace
the brake pad.
Replacement of the bearings(Fig, Q/R)
Note:
The quality of the ball bearings and their maintenance are crucial for the
smooth running of your inline skates Paramount for your inline skates.
- Remove the roller (1o) as described in the section “Replacing the rollers”.
- Press out the other bearing (1s) by pressing with an Allen key (3).
- Push in a new bearing (1s). Turn the wheel (1o) over, insert the spacer (1r) and then press in a second new bearing (1s).
- Secure the roller (1o) again as described in the section “Replacing the rollers” (1p).
Storage, cleaning
Inline skates are technically-constructed sport and recreation devices, so use
them according to skill level and skating style. We recommend that you clean
and dry the item thoroughly after use.
Remove small stones or other objects that may have got caught on the wheels.
Remove sharp edges that may have occurred during skating. Always store your
inline skates in a dry place.
- After skating, clean the bearings with a dry cloth. Dry wet or damp ball bearings with a clean cloth. Grease the bearings with a suitable bearing lubricant from the outside to prevent external rust.
- Bearings are generally locked and cannot be greased from the inside. Worn bearings must be replaced.
Error management
-
Rollers or bearings emit a noise
Remove the rollers from the frame, take them out and clean the bearings with a dry cloth. -
Rollers wear out quickly
-
Block rollers
-
Don’t tighten the bolt too much.
Skate pulls to the left or to the right
This is dependent on the user. Replace rollers which show one-sided wear. -
The brake does not function properly
Worn brakes are dangerous! The braking effect can be reduced. Check for brake wear before each journey.
If braking control or effectiveness deteriorates before the wear limit mark is reached, the brakes must be replaced. At the latest, replace the brakes when they reach the wear limit mark. -
Brake problems
Keep a good following distance. The faster you skate, the bigger your braking ratio. Ensure that you understand the braking tech-niques and practice these on a smooth surface or facility. -
Ankles are often sprained
Ensure that the shoelaces are tight enough. -
Problems with the base of the foot
You are probably not used to this kind of movement. Control areas which cause problems and ad. just the inline skates afresh. Try to wear thick socks.
Disposal
Dispose of the article and the packaging materials in accordance with current
local regulations. Packaging materials such as foil bags are not suitable to
be given to children. Keep the packaging materials out of the reach of
children.
Dispose of the products and the packaging in an environmentally friendly
manner.
The recycling code is used to identify various materials for recycling. The
code consists of the recycling symbol – which is meant to reflect the recycling
cycle – and a number which identifies the material.
Notes The product was produced with great care and under constant
supervision. You receive one year warranty for this product from the date of
purchase. Please retain your receipt. The warranty applies only to material
and workmanship and does not apply to misuse or improper handling. Your
statutory rights, especially the warranty rights, are not affected by this
warranty. With regard to complaints, please contact the following service
hotline or contact us by e-mail. Our service employees will advise as to the
subsequent procedure as quickly as possible. We will be personally available
to discuss the situation with you. on the guarantee and service handling Any
repairs under the warranty, statutory guarantees or through goodwill do not
extend the warranty period. This also applies to replaced and repaired parts.
Repairs after the warranty are subject to a charge.
Contact
Contact us if you experience issues relating to riding, maintenance and
safety, or errors/faults with your inline skates.
E-mail Service: service@gyroor.com
support@gyroorboard.com
Facebook @gyroorboard
Instagram: gyroorboard
Website: www.gyroor.com
Have your order number on hand when contacting Gyroor.
Learn more News about the Gyroor inline skate?
Scan “Gyroorboard” Messenger QR code to get it soon.
The manufacturer reserves the right to make changes to the product, and
updates this manual at any time.
Visit www.gyroorboard.com to download the latest
user manual.
www.gyroorboard.com
References
- Gyroor: The Best Hoverbooard Electric Selfbalance and Scooter of 2019 – GYROOR
- Electric Bikes & Electric Scooters Store | GYROOR
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>