yeedi k600 Robot Vacuum Cleaner Remote Control User Manual

yeedi k600 Robot Vacuum Cleaner Remote Control

Important Safety Instructions

Household use only

When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire or serious injury.

1. Do not allow to be used as a toy Close attention is necessary when used by or near children

2. Clear the area to be cleaned. Remove power cords and small objects from the floor that could entangle the Appliance. Tuck rug fringe under the rug base, and lift items such as curtains and tablecloths off the floor.

3. If there is a drop off in the cleaning area due to a step or stairs, you should operate the Appliance to ensure that it can detect the step without falling over the edge It may become necessary to place a physical barrier at the edge to keep the unit from falling. Make sure the physical barrier is not a trip hazard.

4. Only use as described in this manual. Only use attachments recommended or sold by the manufacturer.

5. Please make sure your power supply voltage matches the power voltage marked on the Charging Dock.

6. For INDOOR use ONLY. Do not use the Appliance in outdoor, commercial or industrial environments.

7. Non-rechargeable batteries are prohibited.

8. Do not use without dust bin and/or filters in place.

9. Do not operate the Appliance in an area where there are lit candles or fragile objects on the floor to be cleaned.

10. Do not use and store in extremely hot or  cold environments (below -5°C/23˚F or above 40°C/104˚F). Please charge the robot in temperature above 0°C/32°F and below  40°C/104°F.

11. Keep hair, loose clothing, fingers, and all parts of body away from any openings and moving parts.

12. Do not operate the Appliance in a room where an infant or child is sleeping.

13. Do not use Appliance on wet surfaces or surfaces with standing water.

14. Do not allow the Appliance to pick up large objects like stones, large pieces of paper or any item that may clog the Appliance.

15. Do not use Appliance to pick up flammable or  combustible materials such as gasoline, printer or copier toner, or use in areas where they may be present.

16. Do not use Appliance to pick up anything that is burning or smoking, such as cigarettes, matches,  hot ashes, or anything that could cause a fire.

17. Do not put objects into the suction intake. Do  not use if the suction intake is blocked. Keep the intake clear of dust, lint, hair, or anything that may reduce air flow.

18. Take care not to damage the power cord. Do not pull on or carry the Appliance or Charging  Dock by the power cord, use the power cord as a handle, close a door on the power cord, or pull power cord around sharp edges or corners. Do not run Appliance over the power cord. Keep power cord away from hot surfaces. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

19. If the power cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.

20. Do not use the Charging Dock if it is damaged.

21. Do not use with a damaged power cord or receptacle. Do not use the Appliance or Charging Dock if it is not working properly, has been dropped, damaged, left outdoors, or come in contact with water It must be repaired by the manufacturer or its service agent in order to avoid a hazard

22. Turn OFF the power switch before cleaning or maintaining the Appliance

23. The plug must be removed from the receptacle before cleaning or maintaining the Charging Dock

24. Remove the Appliance from the Charging Dock,  and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance.

25. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance.

26. Please dispose of used batteries according to local laws and regulations.

27. Do not incinerate the Appliance even if it is severely damaged. The batteries can explode in a fire.

28. When not using the Charging Dock for a long period of time, please unplug it.

29. The Appliance must be used in accordance with the directions in this Instruction Manual. REECOO cannot be held liable or responsible for any damages or injuries caused by improper use.

30. the robot contains batteries that are only replaceable
    by skilled persons. To replace or remove the battery, please contact Customer Service.

31. If the robot will not be used for a long time, fully charge the robot and power OFF for storage and unplug the Charging Dock.

32. Prevent unintentional starting. Ensure the switch is in the off position before connecting to battery pack, picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.

33. When battery pack is not in use, keep it away  from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

34. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

35. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.

36. Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion. The temperature of 130°C can be replaced by the temperature of 265°F.

37. Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.

38. Have servicing performed by a qualified repair person using only identical replacement parts.This will ensure that the safety of the product is maintained.

39. Do not modify or attempt to repair the appliance or the battery pack (as applicable) except as  indicated in the instructions for use and care.

40. Place the cords from other appliances out of the area to be cleaned.

41.  Do not operate the vacuum in a room that has
    lit candles on furniture that the vacuum may accidentally hit or bump into.

42. Do not allow children to sit on the vacuum.

43. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

44. Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire

45. Do not handle plug or appliance with wet  hands.

SAVE THESE INSTRUCTIONS

This device complies with Part 15 of the FCC Rules / Industry Canada licence- exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Package Contents

Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to changes without notice.

Product Diagram

Robot

Bottom View

Charging Dock

Remote Control

Operating and Programming

Notes Before Cleaning

WARNING: Do not use the robot on wet surfaces or surfaces with standing water.

Before using the product on a rug with tasseled edges, please fold the rug edges under.

Tidy up the area to be cleaned by putting furniture, such as chairs, in their proper place.

It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge.

Remove power cords and small objects from the floor that the robot could be obstructed by.

Preparation

1. Plug in Adapter
2. Charging Dock Placement
3. Install Side Brushes
4. Power ON
5. Charge the robot

No te: When the robot completes the cleaning cycle or when battery power gets low, the robot automatically returns to the Charging Dock to recharge itself.

Selecting Cleaning Mode

1. AUTO Cleaning Mode
   A Random Cleaning Pattern (optimized for carpets) will be selected by default

2. Return to Docking Station

3. Edge Cleaning Mode

4. Spot Cleaning Mode

Switch vacuum power

Pause, Wake Up, Power Off

1. PauseNote: the robot’s Control Panel stops glowing after the robot is paused for a few minutes. Press the AUTO Mode Button on the robot to wake up the robot.
2. Wake UpPress the AUTO button on the robot to wake it up
3. Power OFF Note: When the robot is not working, it is recommended to keep it switched ON and charging.

Maintenance

Dust Bin and Filters

Dust Bin

Main Brush and Side Brushes

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Main Brush Side Brushes

Other Components

Note: Before cleaning the robot’s Charging Contacts and Charging Dock Pins, turn the robot OFF and unplug the Charging Dock.

Regular Maintenance

To keep the robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

Universal Wheel Anti-Drop Sensors Bumper

Charging Contacts Charging Dock Pins

| Once per week| /

A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: YEEDI manufactures various replacement parts and fittings. Please contact Customer Service for more information on replacement parts.

Indicator Light

Alarm Sounds
If the robot detects a problem, it emits alarm beeps and the AUTO Mode Button flashes RED or glows RED.

Flashing RED:

for debris and remove the debris.
Three Beeps| Anti-Drop Sensors Malfunction| Clean Anti-Drop Sensors as described in section 4 Maintenance.
Four Beeps| Low Battery| Manually place the robot on the Charging Dock to charge.

Indicator Light and Alarm Sounds

Glowing a continuous RED:

debris and clean as described in section 4 Maintenance.
Two Beeps| Side Brush malfunction| Check Side Brushes for tangled hair or debris and clean as described in section 4 Maintenance.
Four Beeps| Main Brush malfunction| Check Main Brush for tangled hair or debris and clean as described in section 4 Maintenance.

Troubleshooting

robot .
The robot has not connected to the Charging Dock .| Be sure that the robot’s Charging Contacts have connected to the Charging Dock Pins .
The battery is completely discharged .| Re-activate the battery . Switch ON the robot . Place the robot on the Charging Dock by hand, remove after charging for 3 minutes, repeat 3 times; then charge normally .
2| The robot cannot return to the Charging Dock .| The Charging Dock is not correctly placed .| Refer to section 3 .2 to correctly place the Charging Dock .
3| The robot gets stuck while working and stops .| The robot is tangled with something on the floor (electrical wires, curtains, carpet fringing, etc .) .| The robot will try various ways to free itself . If it is unsuccessful, manually remove the obstacles and restart .

4

| ****

The robot returns to the Charging Dock before it has finished cleaning .

| When the battery gets low, the robot automatically switches to Return to Charger Mode and returns to the Charging Dock to recharge itself .| This is normal . No solution necessary .
Working time varies according to floor surface, room complexity and the Cleaning Mode selected .| This is normal . No solution necessary .
5| The robot does not clean the whole area .| The cleaning area is not tidy .| Remove small objects from the floor and tidy up the cleaning area before the robot starts cleaning .

Technical Specifications

Charging Dock
Rated Output Voltage| 19V DC| Rated Output Current| 0 .6A
Power Adapter Model| DK18-190060H-U
Rated Input| 100-120V AC 50-60Hz 0 .5A
Rated Output| 19V DC 0 .6A

Note: Technical and design specifications may be changed for continuous product improvement.

Shenzhen Reecoo Electronic Co., Ltd.
Building 5-6, Shanglilang Technology Park, Longgang District, Shenzhen, P.R.China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>