yeedi DVX34 vac Station Robot Vacuum Instruction Manual

yeedi DVX34 vac Station Robot Vacuum

Product Information: Yeedi Vac Station

The Yeedi Vac Station is an electrical appliance designed for cleaning floors. It comes with a Self-empty Station that allows for automatic dirt disposal. The appliance is suitable for use by individuals above 8 years of age and those with reduced physical,sensory, or mental capabilities. It has safety features for hazard-free use.

Important Safety Instructions

• Read all instructions before using the appliance
• Keep the appliance out of reach of children
• Do not use the appliance to pick up flammable or combustible materials such as gasoline or copier toner
• Do not operate the appliance in a room where an infant or child is sleeping
• Do not use the Self-empty Station if it is damaged
• Turn OFF the power switch before cleaning or maintaining the Appliance

Product Usage Instructions

Before using the Yeedi Vac Station, clear the area to be cleaned. Remove power cords and small objects from the floor that could entangle the appliance. Tuck rug fringe under the rug base and lift items such as curtains and tablecloths off the floor.

Make sure that the suction intake is clear of dust, lint, hair,or anything that may reduce air flow. Do not put objects into the suction intake.

When using the Self-empty Station, remove the appliance from the station and turn off the power switch on the appliance before removing the battery for disposal. Turn off the power switch before cleaning or maintaining the Self- empty Station. Remove the plug from the receptacle before cleaning or maintaining the Self-empty Station.

Do not use the appliance or Self-empty Station if it is not working properly, has been dropped, damaged, left outdoors or come in contact with water. It must be repaired by the manufacturer or its service agent to avoid hazards.

Follow these instructions for safe and efficient use of the Yeedi Vac Station. For further assistance, contact our product expert.

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical Appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
SAVE THESE INSTRUCTIONS

1. This Appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the Appliance in a safe way and understand the hazards involved. Children shall not play with the Appliance. Cleaning and user maintenance shall not be made by children without supervision.
2. Clear the area to be cleaned. Remove power cords and small objects from the floor that could entangle the Appliance. Tuck rug fringe under the rug base, and lift items such as curtains and tablecloths off the floor.
3. If there is a drop off in the cleaning area due to a step or stairs, you should operate the Appliance to ensure that it can detect the step without falling over the edge. It may become necessary to place a physical barrier at the edge to keep the unit from falling. Make sure the physical barrier is not a trip hazard.
4. Only use as described in this manual. Only use attachments recommended or sold by the manufacturer.
5. Please make sure your power supply source voltage matches the power voltage marked on the Self-empty Station.
6. For INDOOR household use ONLY. Do not use the Appliance in outdoor, commercial or industrial environments.
7. Use only the original rechargeable battery and Self-empty Station provided with the Appliance from the manufacturer. Non-rechargeable batteries are prohibited.
8. Do not use without dust bin and/or filters in place.
9. Do not operate the Appliance in an area where there are lit candles or fragile objects.
10. Do not use in extremely hot or cold environments (below -5˚C/23˚F or above 40˚C/104˚F).
11. Keep hair, loose clothing, fingers, and all parts of body away from any openings and moving parts.
12. Do not operate the Appliance in a room where an infant or child is sleeping.
13. Do not use Appliance on wet surfaces or surfaces with standing water.
14. Do not allow the Appliance to pick up large objects like stones, large pieces of paper or any item that may clog the Appliance.
15. Do not use Appliance to pick up flammable or combustible materials such as gasoline, printer or copier toner, or use in areas where they may be present.
16. Do not use Appliance to pick up anything that is burning or smoking, such as cigarettes, matches, hot ashes, or anything that could cause a fire.
17. Do not put objects into the suction intake. Do not use if the suction intake is blocked. Keep the intake clear of dust, lint, hair, or anything that may reduce air flow.
18. Take care not to damage the power cord. Do not pull on or carry the Appliance or Self-empty Station by the power cord, use the power cord as a handle, close a door on the power cord, or pull power cord around sharp edges or corners. Do not run Appliance over the power cord. Keep power cord away from hot surfaces.
19. If the power cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.
20. Do not use the Self-empty Station if it is damaged. The power supply is not to be repaired and not to be used any longer if it is damaged or defective.
21. Do not use with a damaged power cord or receptacle. Do not use the Appliance or Self-empty Station if it is not working properly, has been dropped, damaged, left outdoors, or come in contact with water. It must be repaired by the manufacturer or its service agent in order to avoid a hazard.
22. Turn OFF the power switch before cleaning or maintaining the Appliance.
23. The plug must be removed from the receptacle before cleaning or maintaining the Self-empty Station.
24. Remove the Appliance from the Self-empty Station, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance.
25. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance.
26. Please dispose of used batteries according to local laws and regulations.
27. Do not incinerate the Appliance even if it is severely damaged. The batteries can explode in a fire.
28. When not using the Self-empty Station for a long period of time, please unplug it.
29. The Appliance must be used in accordance with the directions in this Instruction Manual. yeedi cannot be held liable or responsible for any damages or injuries caused by improper use.
30. The robot contains batteries that are only replaceable by skilled persons. To replace the robot’s battery, please contact Customer Service.
31. If the robot will not be used for a long time, power OFF the robot for storage and unplug the Self-empty Station.
32. WARNING: For the purposes of recharging the battery, only use the detachable supply unit CH1918 provided with the Appliance.

To satisfy RF exposure requirements, a separation distance of 20 cm or more should be maintained between this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

To disable Wi-Fi module on Robot, power the robot ON.
Place the robot on the Self-empty Station making sure the Charging Contacts on Robot and the Self-empty Station Pins make a connection. Press and hold the AUTO Mode Button on the robot for 20 seconds until Robot emits 3 beeps. To enable Wi-Fi module on Robot, power the robot OFF and then power ON. The Wi- Fi module is turned on when Robot is restarted.

| Class II
---|---
| Short-circuit-proof safety isolating transformer
| Switch mode power supply
| For indoor use only
| Direct current
| Alternating current

Package Contents

Note: Figures and illustrations are for reference only and may differ from actual product appearance. Product design and specifications are subject to changes without notice.

Product Diagram

Robot

Bottom View

Dust Bin

Reservoir

Self-empty Station

Self-empty Station (Back)

Self-empty Station (Top)

Self-empty Station (Bottom)

Power Cord

Operating and Programming

Notes Before Cleaning

• Tidy up the area to be cleaned by putting furniture, such as chairs, in their proper place.
• During the first use, make sure each room door is open to help Robot fully explore your house.
• It may be necessary to place a physical barrier at the edge of a drop to stop the unit from falling over the edge.

Put away objects including wires, cloths and slippers, etc. on the floor to improve the cleaning efficiency.

Before using the product on a rug with tasseled edges, please fold the rug edges under.

Please do not stand in narrow spaces, such as hallways, and make sure not to block the Detection Sensor.

Preparation

Please remove all protection materials on Robot and Self-empty Station before use.

1. Connect the Dust Container and the Base
2. Tighten the Base Socket Set Screws
3. Assemble Self-empty Station
4. Install the Ramp Extension
5. Self-empty Station Placement
6. Install Edge Brush
7. Power ON
8. Charge Robot

Note: When Robot completes the cleaning cycle or when the battery gets low, Robot automatically returns to the Self-empty Station to recharge itself. Robot can also be sent back to the Self-empty Station at any time by using the yeedi App or by pressing the AUTO Button on the robot for 3 seconds.
Empty remaining water from the Reservoir and remove the Mopping Pad Plate before charging Robot.

yeedi App

To enjoy all available features, it is recommended to control your Robot via the yeedi App.

Before you start, make sure that:

• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on Robot is slowly flashing.

Wi-Fi Indicator Light

| Slowly flashing| Disconnected to Wi-Fi or waiting for Wi-Fi connection
---|---|---
Rapidly flashing| Connecting to Wi-Fi
Solid| Connected to Wi-Fi

Tips:
If you have any problems during the Wi-Fi setup process, refer to the Troubleshooting > Wi-Fi Connection section in this manual.

Start, Pause, Wake Up, Power Off

1. Start

2. Pause
   Note: The robot’s Control Panel stops glowing after the robot is paused for a few minutes. Press the AUTO Mode Button on Robot to wake it up.

3. Wake Up

4. Power OFF

Note: When Robot is not working, it is recommended to keep it switched ON and charging.

Mopping System

Note:

1. To prolong the service life of the reservoir, it is recommended to use purified water or softened water for the mopping system.
2. If you need to clean the carpet, please uninstall the Mopping Pad Plate first.
3. Empty the reservoir after Robot finishes mopping.

Maintenance

Mopping System

Before performing cleaning and maintenance tasks on Robot, turn the robot OFF and unplug the Self-empty Station.

Dust Bin and Filters

Dust Bin

Note: 1. Please rinse the filter with water as shown above. 2. Do not use finger or brush to clean the filter.
Be sure to dry out the filter for at least 24 hours after washing.

Main Brush, Edge Brush and Mapping Sensor

Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Main Brush

Other Components

Note: Before cleaning the robot’s Charging Contacts and Self-empty Station Pins, turn the robot OFF and unplug the Self-empty Station.

Self-empty Station

Note: Before performing cleaning and maintenance on Self-empty Station, unplug it first.
For a proper maintenance, wipe with a clean dry cloth, and avoid using any detergent or cleaning spray.

Dust Bag

1. Dispose the Dust Bag
2. Clean the Blower Cover
3. Install the Dust Bag
4. Close the Dust Container Lid

Dust Evacuation Tube

Regular Maintenance
To keep Robot running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

Universal Wheel

Anti-Drop Sensors Bumper Mapping Sensor Charging Contacts

Self-empty Station Pins

| Once per week| /

A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: yeedi manufactures various replacement parts and fittings. Please contact Customer Service for more information on replacement parts.

Indicator Light

Robot
Robot will tell you something is wrong with an indicator light and voice report. More detailed support is available through the yeedi app and online website.

The robot is paused while cleaning.
AUTO Mode Button flashes WHITE.| The robot is charging.
The robot is starting.
The robot is relocating.
AUTO Mode Button glows a solid RED.| The robot has low battery.
AUTO Mode Button flashes RED.| The robot has a problem.

Self-empty Station
The light effect of the Status Indicator on Self-empty Station corresponds to different conditions and solutions. For more support, please refer to yeedi App or the Troubleshooting Section of this manual.

Indicator light off

| The Self-empty Station is in standby.| /
Robot is in Do Not Disturb Mode.| /

Glowing a solid WHITE

| Robot returns to the Self-empty Station and starts to self-empty.| /
Robot is self-emptying.| /
The Self-empty Station’s suction power decreased.| Please check the Dust Bag.

Glowing a solid RED

| The Dust Bag is not installed.| Please install the Dust Bag.
The Self-empty Station failed to self-empty the dust.| Please check the solution in the App.
The Dust Container Lid is not closed.| Please make sure the Dust Container Lid is firmly closed.

Troubleshooting

1

|

Robot is not able to connect to the home Wi-Fi network.

| Incorrect home Wi-Fi username or password entered.| Enter the correct home Wi-Fi username and password.
Robot is not within range of your home Wi-Fi signal.| Make sure Robot is within range of your home Wi-Fi signal.
Network setup started before Robot was ready.| Turn ON Power Switch. Press the RESET Button for 3 seconds. Robot is ready for network setup when it plays a musical tune and its Wi-Fi Indicator light flashes slowly.

2

|

Robot is not charging.

| Robot is not switched ON.| Switch ON Robot.
Robot has not connected to the Self-empty Station.| Be sure that the robot’s Charging Contacts have connected to the Self-empty Station Pins.
The Power Cord is not connected to the Self- empty Station.| Make sure the Power Cord is firmly connected to the Self-empty Station.

The battery is completely discharged.

| Re-activate the battery. Switch ON. Place Robot on the Self-empty Station by hand, remove after charging for 3 minutes, repeat 3 times; then charge normally.
Make sure the Self-empty Station is connected to the power supply.| The Self- empty Station is not connected to the power supply.

No.

|

Malfunction

|

Possible Causes

|

Solutions

---|---|---|---

3

|

Robot cannot return to the Self-empty Station.

| The Self-empty Station is not correctly placed.| Refer to section 2.2 to correctly place the Self-empty Station.
The Self-empty Station is disconnected or moved.| Please check if the Self- empty Station is connected to power. Do not move the Self-empty Station manually.
Robot is working in a dark environment.| Make sure to use Robot in a well illuminated environment.
Robot is paused for more than 60 minutes.| Avoid pausing Robot for over 60 minutes.
Robot did not start cleaning from the Self- empty Station.| Make sure Robot starts cleaning from the Self-empty Station.
The Ramp Extension is not installed.| Please install the Ramp Extension so the robot can return to charge successfully.

4

|

Robot returns to the Self- empty Station before it has finished cleaning.

| Robot is working in a dark environment.| Make sure to use Robot in a well illuminated environment.
When the battery gets low, Robot automatically switches to Return to Charger Mode and returns to the Self-empty Station to recharge itself.|

This is normal. No solution necessary.

Working time varies according to floor surface, room complexity and the Cleaning Mode selected.|

This is normal. No solution necessary.

The cleaning area is not tidy.| Remove small objects from the floor and tidy up the cleaning area before Robot starts cleaning.
5| Robot gets stuck while working and stops.| Robot is tangled with something on the floor (electrical wires, curtains, Carpet fringing, etc.).| Robot will try various ways to free itself. If it is unsuccessful, manually remove the obstacles and restart.
6| Robot makes much noise when cleaning.| The brushes are tangled, or the dust bin is stuck.| Clear the debris stuck regularly.

7

|

The water is not coming out of the Reservoir when Robot is mopping.

| The water inlet filter on the bottom of Reservoir is clogged.| Unscrew the water inlet on the bottom of Reservoir and clean the filter.
---|---|---|---
The Reservoir runs out of water.| Add water into the Reservoir.
The water outlets on the bottom of Robot are clogged.| Check the water outlets on the bottom and clean.
8| The reservoir drops out of place during cleaning.| The reservoir is not properly installed.| The reservoir is properly installed when it clicks into place.

9

|

The robot does not start emptying after returning to the Self-empty Station.

| The Dust Container Lid is not closed.| Close the Dust Container Lid.
The Dust Bag is not installed to the Self- empty Station.| Install the Dust Bag and close the Dust Container Lid.
Manually move The robot to the Self-empty Station will not trigger self- emptying.| In order to make sure The robot starts self-empty successfully, avoid picking up and moving the Self-empty Station during the cleaning.
The robot returns to the Self-empty Station running Video Manager in the App.| This is normal.
Do Not Disturb mode is enabled in yeedi App.| This is normal. Disable Do Not Disturb mode in the App, or start self-emptying manually.
The Dust Bag is full.| Replace the Dust Bag and close the Dust Container Lid.
If the possible causes are excluded, it might be a component malfunction.| Please contact customer service.

10

|

The robot fails to self-empty the Dust Bin.

| The Dust Bin is not installed.| Please install the Dust Bin with two Self- empty Outlets on the bottom.
---|---|---|---
The Dust Bag is full.| Replace the Dust Bag and close the Dust Container Lid.
The Self-empty Outlets on the Dust Bin is stuck by debris.| Uninstall the Dust Bin and clean the debris on the Self- empty Outlets.
Dust Evacuation Tube is blocked.| Clean the Dust Evacuation Tube.

11

|

There is debris in the Dust Container.

| Fine particles are absorbed inside the Dust Container through the Dust Bag.| Clean the Dust Container Lid and inner wall.
The Dust Bag is damaged.| Check the Dust Bag and replace it.
12| The robot leaks dust or debris while cleaning.| The Self-empty Outlets are stuck by debris.| Uninstall the Dust Bin and clear the debris.
13| The Base is dirty.| Main Brush has debris on it and requires cleaning.| Clean the Main Brush.

Wi-Fi Connection
Before Wi-Fi setup, make sure Robot, mobile phone, and Wi-Fi network meet the following requirements.

Robot and Mobile Phone Requirements

• Robot is fully charged and the power switch of Robot is turned on.
• Wi-Fi status light slowly flashes.
• Turn off mobile phone’s cellular data (you can turn it back on after setup).

Wi-Fi Network Requirements

• You are using a 2.4GHz or 2.4/5 GHz mixed network.
• Your router supports 802.11b/g/n and IPv4 protocol.
• Do not use a VPN (Virtual Private Network) or Proxy Server.
• Do not use a hidden network.
• WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
• WEP EAP (Enterprise Authentication Protocol) is not supported.
• Use Wi-Fi channels 1-11 in North America and channels 1-13 outside North America (refer to local regulatory agency).
• If you are using a network extender/repeater, the network name (SSID) and password are the same as your primary network.

Product Specifications

Rated Input(Charging)

| For European Union Only| 220-240V       50-60Hz 0.3A
For Russia Only| 220V       50-60Hz 0.3A
Rated Output| 20V         1A
Power (Auto-Disposing)| 1000W
Frequency bands| 2400-2483.5MHz
Off Mode Power| Less than 0.50W
Networked Standby Power| Less than 2.00W

Output power of the Wi-Fi module is less than 100mW.
Note: Technical and design specifications may be changed for continuous product improvement.

Shenzhen Reecoo Electronic Co., Ltd.
Building 5-6, ShangLiLang Science and Technology Park, ShangLiLang Community, NanWan Street, Longgang District, Shenzhen City, Guangdong Province, P. R. China

References

• yeedi Owner Mannuals | yeedi Robot Vacuum – yeedi US
• yeedi Owner Mannuals | yeedi Robot Vacuum – yeedi US
• yeedi | Self-Cleaning Robot Vacuum and Mop | Robot Vacuums – yeedi US
• yeedi Owner Mannuals | yeedi Robot Vacuum – yeedi US

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>