GE APPLIANCES Ultra Low NOx Gas Fired Furnaces User Manual
- June 3, 2024
- GE Appliances
Table of Contents
Ultra Low NOx Gas-Fired
Furnaces
USER’S INFORMATION MANUAL
Ultra Low NOx Gas Fired Furnaces
Congratulations…
…you have one of the most modern gas furnaces made. Your unit has been
carefully selected to keep you warm and comfortable during the winter months.
It will deliver superb performance with only minimal help from you. To keep
your operating costs low and to eliminate unnecessary service calls, we have
provided a few guidelines. These guidelines will help you understand how your
gas furnace operates and how to maintain it so you can get years of safe and
dependable service. Read all the instructions in this manual, and keep all
manuals for future
reference.www.ahridirectory.org
AHRI Certified
The Air-Conditioning, Heating and Refrigeration Institute (AHRI) symbol
verifies that Annual Fuel Utilization Efficiency (AFUE) ratings for our gas
furnaces have been derived from U.S. Government standard tests.
CSA International Design Certified
The CSA International symbols on each nameplate is your assurance that your
furnace design meets nationally recognized standards for safety and
performance.
WARNING
FIRE OR EXPLOSION HAZARD Failure to follow the safety warnings exactly could
result in serious injury, death, or property damage.
WARNING
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach the gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
NOTE: This manual is the property of the homeowner and must be left with
the equipment user.
Notice to Homeowner
This furnace is equipped with safety devices that protect you and your
property. If one or more of these devices is activated, furnace operation will
stop. If your home is left unattended for an extended period of time,
equipment operation must be checked periodically. If this is not possible, the
water supply to the house should be shut off and the pipes should be drained.
This will prevent problems associated with a NO HEAT condition (frozen pipes,
etc.).
CAUTION
Before attempting to perform any service or maintenance, turn the electrical
power to unit OFF at the disconnect switch.
WARNING
Do not set thermostat below 60° F (16° C) in heating mode. Setting thermostat
below 60° F (16° C) reduces the number of heating cycles. Damage to the unit
may occur that is not covered by the warranty.
WARNING
If overheating occurs or if gas supply fails to shut off, shut off the manual
gas valve to the furnace before shutting off electrical supply.
WARNING
Do not use this furnace if any part has been underwater. A flood-damaged
furnace is extremely dangerous. Attempts to use the furnace can result in fire
or explosion. Immediately call a licensed professional service technician (or
equivalent) to inspect the furnace and to replace all gas controls, control
system parts, and electrical parts that have been wet or to replace the
furnace, if deemed necessary.
NOTICE
Any additions, changes, or conversions required in order for the appliance to
satisfactorily meet the application needs must be made by a licensed
professional installer (or equivalent) using factory-specified and approved
parts.
WARNING
Improper installation, adjustment, alteration, service or maintenance can
cause property damage, personal injury or loss of life. Installation and
service must be performed by a licensed professional installer (or
equivalent), a service agency, or the gas supplier.
Safety Instructions
- Keep the furnace area clear and free of combustible material, gasoline, and other flammable vapors and liquids. If it is installed in an insulated area, the furnace must be kept free of insulating material. Insulating material may be combustible.
- After any heavy snow, ice or frozen fog event, the furnace vent pipes may become restricted. Always check the vent system and remove any snow or ice that may be obstructing the exhaust pipe and intake pipe (where applicable).
- DO NOT obstruct air flow to unit. Unit must receive an unobstructed flow of combustion and ventilating air. DO NOT block or obstruct air openings on the furnace or air openings to the area in which the furnace is installed. Take care to maintain established clearances surrounding the furnace.
- DO NOT store chlorine or fluorine products near unit or introduce these products into the combustion air. These products can cause furnace corrosion.
- DO NOT draw return air from a room where this furnace, or any other gas appliance (ie., a water heater), is installed. When return air is drawn from a room, a negative pressure is created in the room. If a gas appliance is operating in a room with negative pressure, the flue products can be pulled back down the vent pipe and into the room. This reverse flow of the flue gas may result in incomplete combustion and the formation of carbon monoxide gas. This toxic gas might then be distributed throughout the house by the furnace duct system.
WARNING
The blower door must be securely in place when the blower and burners are
operating. Gas fumes, which could contain carbon monoxide, can be drawn into
the living space resulting in personal injury or death.
Your furnace is a gas appliance. It is critical that the gas supplied to
the unit be completely burned to avoid the production of carbon monoxide gas.
Complete combustion of the gas requires, but is not limited to correct gas
pressure and gas flow rate, adequate combustion air, and proper venting.
WARNING
Carbon monoxide gas is invisible, odorless and toxic.
Exposure to carbon monoxide gas can cause personal injury and even death to
all occupants, including pets. Any item that is powered by or gives off heat
from a combustion process (including lawn mowers, automobiles, and fireplaces)
has the potential to produce carbon monoxide gas. Because of this, we
recommend the use of a carbon monoxide detector in your home, even if you do
not own gas appliances. Reliable detectors are available at reasonable retail
prices.
Your furnace is designed to meet standards set by national agencies, and to
operate safely when properly installed and maintained. However, the unit’s
performance can be greatly impacted by the individual installation and the
operating environment. It is your responsibility to ensure that this appliance
is maintained. Proper maintenance is critical for your safety and the
satisfactory operation of the product. It is strongly recommended that annual
inspections and maintenance of this appliance be performed. Contact your
dealer for an inspection by a licensed professional service technician (or
equivalent).
DANGER
DANGER OF EXPLOSION! There are circumstances in which odorant used with
LP/ propane gas can lose its scent. In case of a leak, LP/ propane gas will
settle close to the floor and may be difficult to smell. An LP/propane leak
detector should be installed in all LP applications.
Start-Up and Operational Information
WARNING
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or death.
BEFORE PLACING THE UNIT INTO OPERATION , smell all around the appliance
area for gas. Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
The gas valve on this unit is equipped with a gas control switch. Use only
your hand to move the switch. Never use tools. If the switch will not move by
hand, do not try to repair it. Call a licensed professional service technician
(or equivalent). Force or attempted repair may result in a fire or explosion.
Placing the Gas Furnace Into Operation These units are equipped with an
ignition system. DO NOT attempt to manually light burners on this furnace.
Each time the thermostat calls for heat, the burners will automatically light.
The ignitor does not get hot when there is no call for heat on units with this
ignition system.
Operating the Gas Valve See Figure 1
-
STOP! Read the safety information at the beginning of this section.
-
Set the thermostat to the lowest setting.
-
Turn OFF all electrical power to the unit.
-
This furnace is equipped with an ignition device which automatically lights the burners. DO NOT try to light the burners by hand.
-
Remove the heating compartment access panel.
-
Move switch on gas valve to OFF. See Figure 1.
-
Wait five minutes to clear out any gas. If you then smell gas, STOP! Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. If you do not smell gas proceed to the next step.
-
Move switch on gas valve to ON. See Figure 1.
-
Replace the heating compartment access panel.
-
Turn on all electrical power to the unit.
-
Set the thermostat to desired setting.
NOTE: When unit is initially started, steps 1 through 11 may need to be repeated to purge air from gas line. -
If the appliance will not operate, follow the section “Turning Off Gas to the Unit” and call your licensed professional service technician (or equivalent.).
Turning Off Gas to the Unit
- Set the thermostat to the lowest setting.
- Turn OFF all electrical power to the unit if service is to be performed.
- Remove the heating compartment access panel.
- Move switch on gas valve to the OFF position.
- Replace the heating compartment access panel.
Filters
All filters are installed external to the unit. Filters should be inspected
monthly. Clean or replace the filters when necessary to ensure proper furnace
operation.
Replacement filters must be rated for high velocity airflow. Table 1 lists
recommended filter sizes. A filter must be in place when the unit is
operating.
Furnace Cabinet
Width| Filter Size
---|---
Side Return| Bottom Return
14-1/2″| 16 x 25 x 1(1)| 14 x 25×1 (1)
17-1/2″| 16 x 25 x 1 (1)
21″| 20 x25 x 1 (1)
24-1/2″| 16 x25 x 1 (2)| 24 x 25 x 1(1)
Table 1.
Maintenance
A licensed professional service technician (or equivalent) should inspect the
complete system each season (heating and cooling). The following maintenance
procedures should only be conducted by a licensed professional service
technician (or equivalent). Do not attempt to service the unit in any way.
WARNING
ELECTRICAL SHOCK, FIRE, OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in dangerous operation,
serious injury, death or property damage.
Improper servicing could result in dangerous operation, serious injury, death,
or property damage.
Before servicing controls, disconnect all electrical power to furnace.
When servicing controls, label all wires prior to disconnecting. Take care to
reconnect wires correctly. Verify proper operation after servicing.
Annually (before heating season) inspect furnace venting system, vent cap,
heat exchanger, and burners for corrosion, deterioration, or deposits of
debris. Remove any obstructions.
During a seasonal check the service technician will conduct a combustion
analysis. The technician will also inspect the indoor blower, burner flames,
electrical connections and the venting system.
Venting System
WARNING
ASPHYXIATION HAZARD
The exhaust vent for this furnace must be leak-free and must be securely
connected to the furnace flue collar at all times.
For your safety and to fulfill the terms of the limited warranty, a licensed
professional service technician (or equivalent) must annually inspect this
furnace and its vent system.
Inspect the furnace for obvious signs of deterioration. Inspect the furnace
venting system to make sure it is in place, physically sound, and without
holes, corrosion, or blockage.
Vent pipe must be clear and free of obstructions and must slope upward away
from the furnace.
** WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow instructions could result in severe personal injury or
death due to carbon-monoxide poisoning, if combustion products infiltrate the
building. Check that all openings in the outside wall around the vent (and air
intake) pipe(s) are sealed to prevent infiltration of combustion products into
the building. Check that furnace vent (and air intake) terminal (s) are not
obstructed in any way during all seasons.
Ductwork
Inspect the furnace return air duct connection to ensure duct is sealed to the
furnace and terminates outside the space containing the furnace.
Inspect the physical support of the furnace to guarantee that it is sound
without sagging and it maintains a proper seal between unit and ductwork.
Drain and Trap
On condensing furnaces (90% efficient and higher), inspect the condensate
drain and trap for leaks and cracks. The drain and trap must also be cleaned
and the trap must be filled with water.
Blower (Circulating Air)
Check the blower wheel for debris and clean if necessary. The blower motors
are pre-lubricated for extended bearing life. No further lubrication is
needed.
WARNING
The blower access panel must be securely in place when the blower and burners
are operating. Gas fumes, which could contain carbon monoxide, can be drawn
into living space resulting in personal injury or death.
Burner Temperature Switch
This unit is equipped with a burner temperature switch. In the unlikely event
of excessive burner heat, this switch will shut off the flow of gas by closing
the gas valve. The switch is located inside the gas burner area. Excessive
burner temperature can be caused by blockage of the power vent system, a
blocked heat exchanger, or reduced combustion air. If this event occurs, the
unit will not operate properly. The gas supply to the unit should be shut off
and no attempt should be made to place it in operation. The system should be
inspected by a qualified service technician.
Burner Flame
CAUTION
To ensure proper operation, a licensed professional service technician (or
equivalent) should check the burner flame and conduct a combustion analysis
annually.
Cleaning/Replacing the Filter
It is very important to clean or replace the air filter regularly. Dirty
filters are the most common cause of inadequate heating or cooling performance
and can sharply increase the operational costs of your unit. In some cases,
they can double the cost. The air filter should be inspected at least every 6
weeks and cleaned or replaced as required.
Your furnace may use either a disposable filter or a cleanable filter. The
type of filter may be indicated on a label attached to the filter. If a
disposable filter is used, replace with the same type and size. To remove
excess dirt from a cleanable filter, shake filter and/or use a vacuum cleaner.
Wash filter in soap or detergent water and replace after filter is dry.
Cleanable filters do not need to be oiled after washing.
NOTE: Cleanable filters may be replaced with disposable filters. Consult
with a service technician for more information.
If your air distribution system has a central return air filtergrille, the
furnace does not need a filter. Filter-grilles can be maintained the same way
as cleanable filters (see above).
SERVICE REMINDER**
Call your service technician if unit will not operate. Before calling, always
check the following to be sure service is required:
- Check that electrical disconnect switches are ON.
- Check room thermostat for proper setting.
- Replace any blown fuses or reset circuit breakers.
- Gas valve should be ON.
- Air filter should not be plugged, which will limit air flow.
- Is gas turned on at meter?
- Is manual main shut-off valve open?
Record the model and serial number of the furnace. These numbers are on the
unit nameplate.
Serial Number: ____
Model Number: ____
Safety Precautions
If you discover any of the following, shut down your unit, and contact a dealer for an inspection by a licensed professional service technician (or equivalent).
- If you repeatedly hear any new or unfamiliar sounds while your unit is operating, there may be a problem. For example, poorly performing burners can produce unfamiliar noises.
- If you smell any unusual odors, your unit may be operating improperly. For example, units can give off unfamiliar odors if components are required to operate in abnormal conditions.
- Look for visible signs of a malfunctioning unit. Examples include unusual amounts of condensate on windows inside your house, visibly burnt components or unusual dirt or rust accumulations on the vent pipe or in the unit.
- If you experience headache, nausea, fatigue, or dizziness, the cause could be exposure to carbon monoxide gas. This is often misdiagnosed as the flu because symptoms are similar. If you suffer from flu-like symptoms that are exaggerated at home, but seem to subside while you are away from the house, exposure to carbon monoxide could be the cause.
Your vigilance may pay off in early detection of a problem before either
personal injury or property damage occurs.
Do not hesitate to contact a qualified service technician as an investment in
your well being.
Planned Service
You should expect a service technician to check the following items during an
annual inspection. Power to the unit must be shut off for the service
technician’s safety.
Fresh air grilles and louvers (on the unit and in the room where the
furnace is installed) Must be open and unobstructed to provide combustion
air.
Burners – Must be inspected for rust, dirt, or signs of water.
Vent Pipe – Must be inspected for signs of water, damaged or sagging
pipe, or disconnected joints.
Unit Appearance – Must be inspected for rust, dirt, signs if water, burnt
or damaged wires, or components.
Blower Access Door – Must be properly in place and provide a seal between
the return air and the room where the furnace is installed.
Return Air Duct – Must be properly attached and provide an air seal to
the unit.
Operating Performance – Unit must be observed during operation to monitor
proper performance of the unit and the vent system.
Combustion Gases – Flue products must be analyzed and compared to the
unit specifications.
Problems detected during the inspection may make it necessary to temporarily
shut down the furnace until the items can be repaired or replaced.
Pay attention to your furnace. Situations can arise between annual furnace
inspections that may result in unsafe operation. For instance, items
innocently stored next to the furnace may obstruct the combustion air supply.
This could cause incomplete combustion and the production of carbon monoxide
gas.
Repair Parts List
The following repair parts are available from your local distributor. When ordering parts, include the complete furnace model number and serial number listed on the unit nameplate. All service must be done by a licensed professional installer (or equivalent), a service agency, or the gas supplier.
Cabinet Parts
- Heating Compartment Access Panel
- Blower Access Panel
- Top Cap
Control Panel Parts
- Transformer
- Integrated Control
- Door Interlock Switch
Blower Parts
- Blower Wheel
- Motor
- Motor Mounting Frame
- Motor Capacitor
- Blower Housing Cutoff Plate
Heating Parts
- Flame Sensor
- Heat Exchanger Assembly
- Gas Manifold
- Combustion Air Inducer
- Gas Valve
- Pre-Mix Burner
- Burner Orifice
- Pressure Switches
- Ignitor
- Primary Limit Control
- Secondary Limit Control
- Burner Temperature Switch
ATTENTION HOMEOWNER
Check for the “WARRANTY” document in the business size envelope in literature
bag assembly inside of box your unit came in.
(If for some unknown reason you cannot find the warranty, please go online at
www.marsdelivers.com
www.alpinehomeair.com
https://mrcool.com/warranty www.GEAppliances.com/extended-
warranty to print out one.)
GE Appliances
A Haier Company
Appliance Park
Louisville, KY 40225
Save these instructions for future reference
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>