BOMANN VSE 7804.1 Household Built In Full Room Refrigerator Instruction Manual

BOMANN VSE 7804.1 Household Built In Full Room Refrigerator

Introduction

Thank you for choosing our product. We hope you will enjoy using the appliance.

Symbols in these Instructions for Use

Important information for your safety is specially marked. It is essential to comply with these instructions to avoid accidents and prevent damage.

| WARNING :
This warns you of dangers to your health and indicates possible injury risks.
---|---
| CAUTION:
This refers to possible hazards to the machine or other objects.
| NOTE:
This highlights tips and information.

General Notes

Read the operating instructions very carefully before putting the appliance into operation and keep the instructions including the warranty and the receipt. If you give this device to other people, also pass on the operating instructions.

| NOTE:

• Due to constant product modifications, your device may differ slightly from these operating instructions; Functions and methods of use remain unchanged.
• The illustrations in these operating instructions may differ from the original device.

---|---

• The appliance is designed exclusively for private use and for the envisaged purpose. This appliance is not fit for commercial use.
• The appliance is only to be used as described in the user manual. Do not use the appliance for any other purpose. Any other use is not intended and can result in damages or personal injuries.
• Operate the appliance only properly installed.
• Do not use it outdoors. Keep it away from sources of heat, direct sunlight and humidity.
• When not in use, for cleaning, user maintenance works or with disruption, switch off the appliance and disconnect the plug (pull the plug itself, not the lead) or turn off the fuse.
• The appliance and if possible the mains lead have to be checked regularly for signs of damage. If damage is found the appliance must not be used.
• For safety reasons, alterations or modifications of the appliance are prohibited.
• To ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

| Do not allow small children to play with the foil.
There is a danger of suffocation!
---|---

Special safety Information for this Unit

• This unit is intended to be used in household and similar applications such as
  – staff kitchen areas in shops, offices and other working environments;
  – farm houses and by clients in hotels, motels and other residential type environments;
  – bed and breakfast type environments;
  – catering and similar non-retail applications.| WARNING:

  • Keep ventilation openings, in the appliance enclosure or in the built-in
    structure, clear of obstruction.

  • Do not use mechanical devices or other means to accelerate the defrosting process (if necessary), except those described in this manual
    (depending on the model included the scope of delivery).

  • Do not damage the refrigerant circuit.

  • Do not operate any electrical devices inside the appliance.

  • Do not store explosive substances such as aerosol containers with
    flammable propellant in the appliance.
    ---|---

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understandthe hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children unless they are older 8 years and supervised.

• NOTE: Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.

• When positioning the appliance, ensure the supply cord is not trappe or damaged.

• Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by qualified person and with a cable of the same type.

• Use the provided collection points of electrical equipment for the disposal of the appliance.

Coolant

| WARNING: R Risk of fire / flammable materials
The coolant circuit of this unit contains the refrigerant Isobutane (R600a), a natural gas that is flammable and of high environmental compatibility. Make sure no parts of the coolant circuit get damaged during transport and installation of the appliance
---|---

If the coolant circuit is damaged:

• avoid any open flames or ignition source,
• disconnect the plug,
• thoroughly air the room in which the appliance is installed and
• contact an authorized technician.

Transport and Packaging

Transport the appliance

Transport the appliance, if possible, in vertical position. Otherwise, it is absolutely necessary to allow the appliance standing upright for a few hours before installation ”Prior to first use”. Protect the appliance during transport against weather influences.

Unpacking the appliance

• Remove the appliance from its packaging.
• Remove all packaging material, such as foils, filler and cardboard packaging.
• To prevent hazards, check the appliance for any transport damage.
• In case of damage, do not put the appliance into operation. Contact your distributor.

| Production residue or dust may have collected on the appliance. We recommend cleaning the appliance according to chapter “Cleaning and Maintenance”.
---|---

Appliance Equipment

Appliance overview

1. Temperature control / Interior light
2. Glass shelves
3. Vegetable box
4. Door storage racks

Delivery scope

3x glass shelf, 1x vegetable box, 3x door storage rack, 1x egg tray, incl. mounting material

Installation

Conditions for the installation location

• Good ventilation is required around the appliance to dissipate the heat properly and to guarantee efficient cooling operation at low power consumption. Enough clearance is necessary.
  – Refer to the instructions which we give you in “Built-in”;
  – Place the appliance so that the appliance door can open without being impeded.

• Only install at a location with an ambient temperature suitable for the climate class of the appliance.
  The climate class can be found under “Technical Data” and on the rating label located in the interior or on the appliance rear.

• Look for stable, horizontal appliance position.

• Avoid the installation:
  – near heaters, next to a stove, direct sunlight or any other heat sources;
  – at locations with high humidity (e.g. outdoors, bathroom), as metal parts would be susceptible to corrosion under such circumstances;
  – near volatile or flammable materials (e.g. gas, fuel, alcohol, paint, etc.), in rooms which may have poor air circulation (e.g. garages).
  – Do not expose the appliance any weathe

Electrical connection

| WARNING:

• The installation to the mains supply must conform to the local standards and regulations.
• Improper connection may cause to an electric shock!
• Do not modify the appliance plug. If the plug does not fit properly to the outlet, let install a proper outlet by an authorized specialist.
• The accessibility of the power plug must be ensured to disconnect the appliance from the power supply in case of emergency.

---|---

• Make sure that the voltage supply matches the specifications on the rating label before connecting.
• Connect the mains cable to a properly installed and earthed wall outlet.
• If the plug after installation is not accessible, a corresponding disconnect device must be available to meet the relevant safety regulations.

Reversing the door opening

| WARNING:
When replacing the door stop, the appliance must be
disconnected from the power supply first.
---|---
| NOTE:

• Ask another person to assist.
• You possibly need: screw wrench, Phillips screwdriver as well as a thin-blade screwdriver.

---|---

• Dismount the upper door hinge, lift the appliance door and set the door safely aside.
• Dismount the lower door hinge.
• Place the respective blind caps on the exposed holes of the upper and lower door hinge.
• Turn over the originally upper door hinge and  install it at the bottom left side.
• Put on the appliance door and fix it in the intended position.
• Turn over the originally lower door hinge and install it at the top left side.
• Check that the door is aligned vertically and horizontally to ensure proper opening and closing of the door.

Built-in

For ventilation, an exhaust duct of approx. 38 mm depth must be provided on the appliance back.
The ventilation openings in the furniture base and building must be min. 200 cm² to ensure that heated air can be freely escape.

Mounting material

| CAUTION:
Before drilling, check the furniture front for sufficient strength for the enclosed screw length.
---|---

1. Install the power cord so that the appliance can be easily connected after installation. Slide the appliance into the build-in opening until the stop plate (A) abuts the furniture.
   Open the appliance door. Push the appliance side, which is located opposite the hinges, against the built-in furniture. Arrange the appliance for a secure, vertical position.

2. Screw the bracket (b) with the screws (S) into the screw holes provided on the appliance door. Insert the guide rail (a).
   Check that the merged doors are optimally aligned vertically and horizontally so that smooth opening and closing is guaranteed. Mark the position of the screw holes for the guide rail (a) on the furniture door.

3. Take the guide rail (a) out of the bracket (b) and fasten the guide rail to the pre-marked position using the screws (S) (possibly pre-drill the screw holes).

4. Insert the cover (c) until it clicks in the guide (a).

5. Release the bracket (b) from the appliance door.
   Open the appliance and furniture door completely and bring them together. Slide the bracket (b) into the guide rail (a) and fasten the bracket again with the screws (S).

6. If an aligning of the furniture door is necessary, use the slot spacing.

7. Insert the cover (d) until it clicks in the bracket (b).

8. Secure the appliance at the top and bottom of the built-in cabinet with the screws (S).

9. Press the rubber seal (R) between the appliance and the built-in furniture (side without hinge).

Startup / Operation

Prior to first use

| CAUTION:
After transport, the appliance should be left standing upright for about four hours before connecting to the power supply. Nonobservance could lead to malfunction of the cooling system and causes an appliance breakdown.
---|---

Clean the appliance interior including all accessory parts. Consider the instructions which we provide in the chapter “Cleaning and Maintenance”.

Starting the appliance

• Connect the appliance to the power supply.
• Operate the temperature control. See also the section “Settings”.

Settings

Setting [ 0 ] means that the appliance is in the off state. Turn the temperature control clockwise, starting from this setting; the appliance will turn on automatically.
The power levels [ 1 – 7 ] regulate the different values of the internal temperature.

Setting 0: Off state
Power level 1 + 2 :
lowest level → warmest internal temperature (Temperature range approx. +4°C∼+10°C)
Power level 3 + 4 :
medium level → optimal operating temperature (Temperature range approx. +3°C∼+7°C)
Power level 5 + 6 + 7* :*
highest level → coldest internal temperature (Temperature range approx. 0°C∼+6°C)
Beware** of high setting because the maximum level may already means “freezing point”.

Basically, the temperature changes depending on the
ambient temperature (place of installation), the frequency of opening the door and the equipment.
During initial operation, adjust the lowest possible temperature (= highest power level) first, until the appliance has reached the desired operating temperature. Afterwards it is recommended to turn the control back to a medium setting; correcting the temperature at a later point would then be easier.

| NOTE:
In generally a medium power level works best for an
optimized food storage. A high power level also increases the energy consumption.
---|---

Interior light

When opening the appliance door, the interior light will turn on automatically.

Storing food

| NOTE: Recommendation!
To guarantee that the temperature is low enough, you should pre-cool the appliance a few times before initial loading foods.
---|---
| CAUTION:
Always pay attention to the storage instructions on the sales packaging.
---|---

Always store food covered or packed to prevent drying-out and transfer of odor or taste onto other food items. You may pack the food with e.g.

• Polyethylene plastic bags or foil
• Plastic bowl with lid
• Special plastic cover with elastic strip
• Aluminum foil

To avoid contamination of food, respect the following instructions:

• Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
• Clean regularly surfaces that can come in contact with food and accessible drainage systems (see “Cleaning and Maintenance”).
• Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
• If the appliance is out of use for long period, follow the instructions under “Switching off”.

Storage space

Depending on requirements, shelves/drawers (partially and depending on model) can be adjusted in height or removed to optimize the storage space.

| NOTE :
For the most efficient use of energy, place all shelves/drawers in their original position.
---|---

Temperature zones and storage recommendations
The optimal cooling temperature is around 5∼7 degrees for the central area of the cooling
Different cooling zones are created by the air circulation. Regardless of the power level, cold air drops off.

• The coldest zone is on the cooling rear wall and in the lower cooling part. Recommended for storing perishable foods such as meat, fish and sausages at around 2∼3 degrees.

• About that it becomes less cold. For dairy products such as yoghurt, cheese and co., the center of the cooling is just the right temperature at around 5 degrees.

• Well-packed leftovers or preserves needs less cooling. The upper cooling part at around 6∼8 degrees could be the right place.

• The cooling door is one of the warmest locations.
  The upper racks are good location for food that needs moderate cooling, such as butter and eggs.
  There is space for drinks in the lower door racks.

• The vegetable box (depending on the model) is suitable for fruit and vegetables at a temperature of around 8 degrees, depending on the cooling temperature. To ensure that delicate fruits and vegetables feel good, a glass shelf above avoids the falling cold.

Operating noise

Switching off

To switch off the appliance turn the temperature control to the off state.
If the appliance is out of use for long periods:

• Remove the appliance content.
• Disconnect the appliance from the power supply.
• Defrost (model dependent) and clean the device thoroughly (see ”Cleaning and Maintenance”).
• Leave open the appliance door to avoid formation of mold and unpleased odors.

Tips for Energy saving

• Disconnect the appliance from the power supply if it isn’t in use.
• Do not install the appliance near stoves, heaters or other heat sources. In case of higher ambienttemperatures, the compressor will run more frequently and longer.
• Ensure enough ventilation at the bottom and rear side. Never block ventilation openings.
• Place all shelves, racks or drawers (depending on the model) in their original position.
• Adjust the temperature not colder than necessary.
• Allow warm food to cool before placing it in the appliance.
• Open the unit door only as necessary.
• Defrost the unit regularly (model dependent).
• The seal of the appliance door must be completely intact, so that the door closes properly

Cleaning and Maintenance

| WARNING:

• Always disconnect the appliance from the power supply before cleaning and user maintenance.
• Do not use steam cleaners for cleaning the appliance; moisture could enter electrical components.
  Risk of electric shock! Hot steam could damage the plastic parts.

---|---
| WARNING:

• The unit must be dry before restarting operation.

---|---
| WARNING:

• Do not use a wire brush or other sharp, abrasive items.
• Do not use any acidic or abrasive detergents.
• Do not damage the refrigerant circuit.

---|---

Cleaning the appliance including interior

• Clean the appliance interior, the exterior surfaces, the accessories and the door seal regularly with warm water and mild detergent; or with a clean, damp microfiber cloth without cleaning agent.
• Remove the appliance content and storage it at a cool location.
• Clean the thaw water discharge channel / opening carefully e.g. with a pipe cleaner.
• After everything was thoroughly dried, you can restart the operation.
• Depending on model: Wipe at least once a year the dust that has accumulated on the appliance back and condenser (metal grille). To do this, use a soft brush or a vacuum cleaner.

Defrosting

| CAUTION:
Never use metal objects (e.g. knifes) to remove ice from the evaporator. Otherwise it can be damaged..
---|---

The appliance has a semi automatic defrosting system. During defrosting water drops drains off at the back of the cooling chamber. The thaw water running through a channel, is collected in a drip tray located on the compressor, where it will evaporate. Make sure the water discharge opening does not get clogged. A light formation of ice on the interior back during operation is normal.
A permanently high power level can lead to increased ice formation. In this case, the appliance can be defrosted manually → set a lower power level.

Changing the bulb

| CAUTION:
Do NOT remove the cover of the interior light.
The LED light may be replaced / repaired in case of failure / defect only by an authorized specialist.
---|---

Troubleshooting

Before you contact an authorized specialist

• Check the power supply / tempera- ture setting / ambient temperature.
• Unblock the ventilation openings, install the appliance freely.

Loading is too warm|

• Check the temperature setting / ambient temperature. ∙ Open the door only as long as necessary.

Loud noise during op- eration|

• Check the appliance position.
• See the section “Operating noise”.

Water on the unit bottom|

• Check the temperature setting / water discharge channel or opening.

Light does not work|

• Check the power supply.
• See “Changing the bulb”.

| NOTE:
If a problem persists after following the steps above, contact your trader or an authorized technician.
---|---

Technical Data

limate class N/ST: this appliance is intended to be used at ambient temperature ranging from 16°C to 38°C.

Electrical connection ……………………………………..
Power voltage: …………………….220-240 V~ / 50 Hz
Rated power: ………………………..….……………80 W
Rated current: …………………………..………….0.45 A
Dimension H x W x D / Weight …..……………………..
Appliance size: …….……………88.0 x 54.0 x 54.0 cm
Net weight: ……………………….……approx. 29.0 kg

For more information about the product, scan the QR code on the supplied energy label and/or visit the official website of the product data bank: https://eprel.ec.europa.eu

The right to make technical and design modifications during continuous product development remains reserved.

This appliance has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations.

**Disposal

**

Meaning of the “Dustbin” Symbol

Protect our environment; do not dispose of electrical equipment in the domestic waste.
Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.
This helps avoid the potential effects of incorrect disposal on the environment and human health. This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment.
Information concerning where these can be disposed of can be obtained from your local authority.

| WARNING:
Remove or disable any existing snap and bolt locks if you take the unit out of operation or dispose it.
---|---

C . BomannGmbH
www.bomann-germany.de
Made in P.R.C.

References

• Bomann Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>